[PATCH 2/2] ARM: s3c24xx: Switch to common GPIO controlled UDC pullup implementation
Lars-Peter Clausen
lars at metafoo.de
Mon Mar 7 02:42:00 EST 2011
Currently all boards using the s3c2410_udc driver use a GPIO to control the
state of the pullup, as a result the same code is reimplemented in each board
This patch changes these boards to use the common implementation for GPIO
controlled pullup in the UDC driver.
Signed-off-by: Lars-Peter Clausen <lars at metafoo.de>
---
arch/arm/mach-s3c2410/mach-h1940.c | 24 +-----------------------
arch/arm/mach-s3c2410/mach-n30.c | 21 +--------------------
arch/arm/mach-s3c2412/mach-smdk2413.c | 24 +-----------------------
arch/arm/mach-s3c2440/mach-gta02.c | 22 ++--------------------
arch/arm/mach-s3c2440/mach-mini2440.c | 24 +-----------------------
arch/arm/mach-s3c2440/mach-rx1950.c | 21 +--------------------
6 files changed, 7 insertions(+), 129 deletions(-)
diff --git a/arch/arm/mach-s3c2410/mach-h1940.c b/arch/arm/mach-s3c2410/mach-h1940.c
index 5531c4c..882b32a 100644
--- a/arch/arm/mach-s3c2410/mach-h1940.c
+++ b/arch/arm/mach-s3c2410/mach-h1940.c
@@ -169,29 +169,10 @@ struct gpio_chip h1940_latch_gpiochip = {
.get = h1940_gpiolib_latch_get,
};
-static void h1940_udc_pullup(enum s3c2410_udc_cmd_e cmd)
-{
- printk(KERN_DEBUG "udc: pullup(%d)\n",cmd);
-
- switch (cmd)
- {
- case S3C2410_UDC_P_ENABLE :
- gpio_set_value(H1940_LATCH_USB_DP, 1);
- break;
- case S3C2410_UDC_P_DISABLE :
- gpio_set_value(H1940_LATCH_USB_DP, 0);
- break;
- case S3C2410_UDC_P_RESET :
- break;
- default:
- break;
- }
-}
-
static struct s3c2410_udc_mach_info h1940_udc_cfg __initdata = {
- .udc_command = h1940_udc_pullup,
.vbus_pin = S3C2410_GPG(5),
.vbus_pin_inverted = 1,
+ .pullup_pin = H1940_LATCH_USB_DP,
};
static struct s3c2410_ts_mach_info h1940_ts_cfg __initdata = {
@@ -742,9 +723,6 @@ static void __init h1940_init(void)
gpio_direction_output(H1940_LATCH_LCD_P4, 0);
gpio_direction_output(H1940_LATCH_MAX1698_nSHUTDOWN, 0);
- gpio_request(H1940_LATCH_USB_DP, "USB pullup");
- gpio_direction_output(H1940_LATCH_USB_DP, 0);
-
gpio_request(H1940_LATCH_SD_POWER, "SD power");
gpio_direction_output(H1940_LATCH_SD_POWER, 0);
diff --git a/arch/arm/mach-s3c2410/mach-n30.c b/arch/arm/mach-s3c2410/mach-n30.c
index 271b9aa..66f4444 100644
--- a/arch/arm/mach-s3c2410/mach-n30.c
+++ b/arch/arm/mach-s3c2410/mach-n30.c
@@ -84,26 +84,10 @@ static struct s3c2410_uartcfg n30_uartcfgs[] = {
},
};
-static void n30_udc_pullup(enum s3c2410_udc_cmd_e cmd)
-{
- switch (cmd) {
- case S3C2410_UDC_P_ENABLE :
- gpio_set_value(S3C2410_GPB(3), 1);
- break;
- case S3C2410_UDC_P_DISABLE :
- gpio_set_value(S3C2410_GPB(3), 0);
- break;
- case S3C2410_UDC_P_RESET :
- break;
- default:
- break;
- }
-}
-
static struct s3c2410_udc_mach_info n30_udc_cfg __initdata = {
- .udc_command = n30_udc_pullup,
.vbus_pin = S3C2410_GPG(1),
.vbus_pin_inverted = 0,
+ .pullup_pin = S3C2410_GPB(3),
};
static struct gpio_keys_button n30_buttons[] = {
@@ -596,9 +580,6 @@ static void __init n30_init(void)
platform_add_devices(n35_devices, ARRAY_SIZE(n35_devices));
}
-
- WARN_ON(gpio_request(S3C2410_GPB(3), "udc pup"));
- gpio_direction_output(S3C2410_GPB(3), 0);
}
MACHINE_START(N30, "Acer-N30")
diff --git a/arch/arm/mach-s3c2412/mach-smdk2413.c b/arch/arm/mach-s3c2412/mach-smdk2413.c
index 8e5758b..834cfb6 100644
--- a/arch/arm/mach-s3c2412/mach-smdk2413.c
+++ b/arch/arm/mach-s3c2412/mach-smdk2413.c
@@ -78,28 +78,9 @@ static struct s3c2410_uartcfg smdk2413_uartcfgs[] __initdata = {
}
};
-static void smdk2413_udc_pullup(enum s3c2410_udc_cmd_e cmd)
-{
- printk(KERN_DEBUG "udc: pullup(%d)\n",cmd);
-
- switch (cmd)
- {
- case S3C2410_UDC_P_ENABLE :
- gpio_set_value(S3C2410_GPF(2), 1);
- break;
- case S3C2410_UDC_P_DISABLE :
- gpio_set_value(S3C2410_GPF(2), 0);
- break;
- case S3C2410_UDC_P_RESET :
- break;
- default:
- break;
- }
-}
-
static struct s3c2410_udc_mach_info smdk2413_udc_cfg __initdata = {
- .udc_command = smdk2413_udc_pullup,
+ .pullup_pin = S3C2410_GPF(2),
};
@@ -133,9 +114,6 @@ static void __init smdk2413_machine_init(void)
{ /* Turn off suspend on both USB ports, and switch the
* selectable USB port to USB device mode. */
- WARN_ON(gpio_request(S3C2410_GPF(2), "udc pull"));
- gpio_direction_output(S3C2410_GPF(2), 0);
-
s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST |
S3C2410_MISCCR_USBSUSPND0 |
S3C2410_MISCCR_USBSUSPND1, 0x0);
diff --git a/arch/arm/mach-s3c2440/mach-gta02.c b/arch/arm/mach-s3c2440/mach-gta02.c
index d217ef3..0db2411 100644
--- a/arch/arm/mach-s3c2440/mach-gta02.c
+++ b/arch/arm/mach-s3c2440/mach-gta02.c
@@ -448,28 +448,10 @@ static struct s3c2410_platform_nand __initdata gta02_nand_info = {
};
-static void gta02_udc_command(enum s3c2410_udc_cmd_e cmd)
-{
- switch (cmd) {
- case S3C2410_UDC_P_ENABLE:
- pr_debug("%s S3C2410_UDC_P_ENABLE\n", __func__);
- gpio_direction_output(GTA02_GPIO_USB_PULLUP, 1);
- break;
- case S3C2410_UDC_P_DISABLE:
- pr_debug("%s S3C2410_UDC_P_DISABLE\n", __func__);
- gpio_direction_output(GTA02_GPIO_USB_PULLUP, 0);
- break;
- case S3C2410_UDC_P_RESET:
- pr_debug("%s S3C2410_UDC_P_RESET\n", __func__);
- /* FIXME: Do something here. */
- }
-}
-
/* Get PMU to set USB current limit accordingly. */
-static struct s3c2410_udc_mach_info gta02_udc_cfg = {
+static struct s3c2410_udc_mach_info gta02_udc_cfg __initdata = {
.vbus_draw = gta02_udc_vbus_draw,
- .udc_command = gta02_udc_command,
-
+ .pullup_pin = GTA02_GPIO_USB_PULLUP,
};
/* USB */
diff --git a/arch/arm/mach-s3c2440/mach-mini2440.c b/arch/arm/mach-s3c2440/mach-mini2440.c
index f62bb4c..d80f129 100644
--- a/arch/arm/mach-s3c2440/mach-mini2440.c
+++ b/arch/arm/mach-s3c2440/mach-mini2440.c
@@ -97,26 +97,8 @@ static struct s3c2410_uartcfg mini2440_uartcfgs[] __initdata = {
/* USB device UDC support */
-static void mini2440_udc_pullup(enum s3c2410_udc_cmd_e cmd)
-{
- pr_debug("udc: pullup(%d)\n", cmd);
-
- switch (cmd) {
- case S3C2410_UDC_P_ENABLE :
- gpio_set_value(S3C2410_GPC(5), 1);
- break;
- case S3C2410_UDC_P_DISABLE :
- gpio_set_value(S3C2410_GPC(5), 0);
- break;
- case S3C2410_UDC_P_RESET :
- break;
- default:
- break;
- }
-}
-
static struct s3c2410_udc_mach_info mini2440_udc_cfg __initdata = {
- .udc_command = mini2440_udc_pullup,
+ .pullup_pin = S3C2410_GPC(5),
};
@@ -644,10 +626,6 @@ static void __init mini2440_init(void)
s3c2410_gpio_setpin(S3C2410_GPB(1), 0);
s3c_gpio_cfgpin(S3C2410_GPB(1), S3C2410_GPIO_INPUT);
- /* Make sure the D+ pullup pin is output */
- WARN_ON(gpio_request(S3C2410_GPC(5), "udc pup"));
- gpio_direction_output(S3C2410_GPC(5), 0);
-
/* mark the key as input, without pullups (there is one on the board) */
for (i = 0; i < ARRAY_SIZE(mini2440_buttons); i++) {
s3c_gpio_setpull(mini2440_buttons[i].gpio, S3C_GPIO_PULL_UP);
diff --git a/arch/arm/mach-s3c2440/mach-rx1950.c b/arch/arm/mach-s3c2440/mach-rx1950.c
index 2d2f4e4..22f18d9 100644
--- a/arch/arm/mach-s3c2440/mach-rx1950.c
+++ b/arch/arm/mach-s3c2440/mach-rx1950.c
@@ -616,26 +616,10 @@ static struct s3c2410_platform_nand rx1950_nand_info = {
.sets = rx1950_nand_sets,
};
-static void rx1950_udc_pullup(enum s3c2410_udc_cmd_e cmd)
-{
- switch (cmd) {
- case S3C2410_UDC_P_ENABLE:
- gpio_direction_output(S3C2410_GPJ(5), 1);
- break;
- case S3C2410_UDC_P_DISABLE:
- gpio_direction_output(S3C2410_GPJ(5), 0);
- break;
- case S3C2410_UDC_P_RESET:
- break;
- default:
- break;
- }
-}
-
static struct s3c2410_udc_mach_info rx1950_udc_cfg __initdata = {
- .udc_command = rx1950_udc_pullup,
.vbus_pin = S3C2410_GPG(5),
.vbus_pin_inverted = 1,
+ .pullup_pin = S3C2410_GPJ(5),
};
static struct s3c2410_ts_mach_info rx1950_ts_cfg __initdata = {
@@ -800,9 +784,6 @@ static void __init rx1950_init_machine(void)
S3C2410_MISCCR_USBSUSPND0 |
S3C2410_MISCCR_USBSUSPND1, 0x0);
- WARN_ON(gpio_request(S3C2410_GPJ(5), "UDC pullup"));
- gpio_direction_output(S3C2410_GPJ(5), 0);
-
/* mmc power is disabled by default */
WARN_ON(gpio_request(S3C2410_GPJ(1), "MMC power"));
gpio_direction_output(S3C2410_GPJ(1), 0);
--
1.7.2.3
More information about the linux-arm-kernel
mailing list