[RFC V4 2/3] ddr_spd: add routune for printing SPD contents in human readable format
Alexander Smirnov
alllecs at yandex.ru
Thu Jul 2 01:50:16 PDT 2015
Signed-off-by: Alexander Smirnov <alllecs at yandex.ru>
---
common/ddr_spd.c | 290 ++++++++++++++++++++++++++++++++++++++++++++++++++++++
include/ddr_spd.h | 1 +
2 files changed, 291 insertions(+)
diff --git a/common/ddr_spd.c b/common/ddr_spd.c
index ea0b529..6757d58 100644
--- a/common/ddr_spd.c
+++ b/common/ddr_spd.c
@@ -61,3 +61,293 @@ uint32_t ddr3_spd_checksum_pass(const struct ddr3_spd_eeprom_s *spd)
return 0;
}
+
+static char *heights[] = {
+ "<25.4",
+ "25.4",
+ "25.4 - 30.0",
+ "30.0",
+ "30.5",
+ "> 30.5",
+};
+
+static char *sdram_voltage_interface_level[] = {
+ "TTL (5V tolerant)",
+ "LVTTL (not 5V tolerant)",
+ "HSTL 1.5V",
+ "SSTL 3.3V",
+ "SSTL 2.5V",
+ "SSTL 1.8V",
+};
+
+static char *ddr2_module_types[] = {
+ "RDIMM (133.35 mm)",
+ "UDIMM (133.25 mm)",
+ "SO-DIMM (67.6 mm)",
+ "Micro-DIMM (45.5 mm)",
+ "Mini-RDIMM (82.0 mm)",
+ "Mini-UDIMM (82.0 mm)",
+};
+
+static char *refresh[] = {
+ "15.625",
+ "3.9",
+ "7.8",
+ "31.3",
+ "62.5",
+ "125",
+};
+
+static char *type_list[] = {
+ "Reserved",
+ "FPM DRAM",
+ "EDO",
+ "Pipelined Nibble",
+ "SDR SDRAM",
+ "Multiplexed ROM",
+ "DDR SGRAM",
+ "DDR SDRAM",
+ [SPD_MEMTYPE_DDR2] = "DDR2 SDRAM",
+ "FB-DIMM",
+ "FB-DIMM Probe",
+ [SPD_MEMTYPE_DDR3] = "DDR3 SDRAM",
+};
+
+static int funct(uint8_t addr)
+{
+ int t;
+
+ t = ((addr >> 4) * 10 + (addr & 0xf));
+
+ return t;
+}
+
+static int des(uint8_t byte)
+{
+ int k;
+
+ k = (byte & 0x3) * 10 / 4;
+
+ return k;
+}
+
+static int integ(uint8_t byte)
+{
+ int k;
+
+ k = (byte >> 2);
+
+ return k;
+}
+
+static int ddr2_sdram_ctime(uint8_t byte)
+{
+ int ctime;
+
+ ctime = (byte >> 4) * 100;
+ if ((byte & 0xf) <= 9)
+ ctime += (byte & 0xf) * 10;
+ else if ((byte & 0xf) == 10)
+ ctime += 25;
+ else if ((byte & 0xf) == 11)
+ ctime += 33;
+ else if ((byte & 0xf) == 12)
+ ctime += 66;
+ else if ((byte & 0xf) == 13)
+ ctime += 75;
+
+ return ctime;
+}
+
+void ddr_spd_print(uint8_t *record)
+{
+ int highestCAS = 0;
+ int cas[256];
+ int i, i_i, k, x, y;
+ int ddrclk, tbits, pcclk;
+ int trcd, trp, tras;
+ int ctime;
+ uint8_t parity;
+ char *ref, *sum;
+ struct ddr2_spd_eeprom_s *s = (struct ddr2_spd_eeprom_s *)record;
+
+ ctime = ddr2_sdram_ctime(s->clk_cycle);
+ ddrclk = 2 * (1000 / ctime) * 100;
+ tbits = (s->res_7 << 8) + (s->dataw);
+ if ((s->config & 0x03) == 1)
+ tbits = tbits - 8;
+
+ pcclk = ddrclk * tbits / 8;
+ pcclk = pcclk - (pcclk % 100);
+ i_i = (s->nrow_addr & 0x0f) + (s->ncol_addr & 0x0f) - 17;
+ k = ((s->mod_ranks & 0x7) + 1) * s->nbanks;
+ trcd = ((s->trcd >> 2) + ((s->trcd & 3) * 0.25)) / ctime * 100;
+ trp = ((s->trp >> 2) + ((s->trp & 3) * 0.25)) / ctime * 100;
+ tras = s->tras * 100 / ctime ;
+ x = (int)(ctime / 100);
+ y = (ctime - (int)((ctime / 100) * 100)) / 10;
+
+ for (i_i = 2; i_i < 7; i_i++) {
+ if (s->cas_lat & 1 << i_i) {
+ highestCAS = i_i;
+ cas[highestCAS]++;
+ }
+ }
+
+ if (ddr2_spd_checksum_pass(s))
+ sum = "ERR";
+ else
+ sum = "OK";
+
+ printf("---=== SPD EEPROM Information ===---\n");
+ printf("%-50s %s (0x%0X)\n", "EEPROM Checksum of bytes 0-62",
+ sum, s->cksum);
+ printf("%-50s %d\n", "# of bytes written to SDRAM EEPROM",
+ s->info_size);
+ printf("%-50s %d\n", "Total number of bytes in EEPROM",
+ 1 << (s->chip_size));
+
+ if (s->mem_type < ARRAY_SIZE(type_list))
+ printf("%-50s %s\n", "Fundamental Memory type",
+ type_list[s->mem_type]);
+ else
+ printf("%-50s (%02x)\n", "Warning: unknown memory type",
+ s->mem_type);
+
+ printf("%-50s %x.%x\n", "SPD Revision", s->spd_rev >> 4,
+ s->spd_rev & 0x0f);
+ if (s->mem_type != SPD_MEMTYPE_DDR2) {
+ printf("Can't dump extended information for non-DDR2 memory\n");
+ return;
+ }
+
+ printf("\n---=== Memory Characteristics ===---\n");
+ printf("%-50s %d MHz (PC2-%d)\n", "Maximum module speed",
+ ddrclk, pcclk);
+ if (i_i > 0 && i_i <= 12 && k > 0)
+ printf("%-50s %d MB\n", "Size", (1 << i_i) * k);
+ else
+ printf("%-50s INVALID: %02x %02x %02x %02x\n", "Size",
+ s->nrow_addr, s->ncol_addr, s->mod_ranks, s->nbanks);
+
+ printf("%-50s %d x %d x %d x %d\n", "Banks x Rows x Columns x Bits",
+ s->nbanks, s->nrow_addr, s->ncol_addr, s->dataw);
+ printf("%-50s %d\n", "Ranks", (s->mod_ranks & 0x7) + 1);
+ printf("%-50s %d bits\n", "SDRAM Device Width", s->primw);
+
+ if (s->mod_ranks >> 5 < ARRAY_SIZE(heights))
+ printf("%-50s %s mm\n", "Module Height",
+ heights[s->mod_ranks >> 5]);
+ else
+ printf("Error height\n");
+
+ if ((fls(s->dimm_type) - 1) < ARRAY_SIZE(ddr2_module_types))
+ printf("%-50s %s\n", "Module Type",
+ ddr2_module_types[fls(s->dimm_type) - 1]);
+ else
+ printf("Error module type\n");
+
+ printf("%-50s ", "DRAM Package ");
+ if ((s->mod_ranks & 0x10) == 1)
+ printf("Stack\n");
+ else
+ printf("Planar\n");
+ if (s->voltage < 7)
+ printf("%-50s %s\n", "Voltage Interface Level",
+ sdram_voltage_interface_level[s->voltage]);
+ else
+ printf("Error Voltage Interface Level\n");
+
+ printf("%-50s ", "Module Configuration Type ");
+
+ parity = s->config & 0x07;
+ if (parity == 0)
+ printf("No Parity\n");
+
+ if ((parity & 0x03) == 0x01)
+ printf("Data Parity\n");
+ if (parity & 0x02)
+ printf("Data ECC\n");
+
+ if (parity & 0x04)
+ printf("Address/Command Parity\n");
+
+ if ((s->refresh >> 7) == 1)
+ ref = "- Self Refresh";
+ else
+ ref = " ";
+
+ printf("%-50s Reduced (%s us) %s\n", "Refresh Rate",
+ refresh[s->refresh & 0x7f], ref);
+ printf("%-50s %d, %d\n", "Supported Burst Lengths",
+ s->burstl & 4, s->burstl & 8);
+
+ printf("%-50s %dT\n", "Supported CAS Latencies (tCL)", highestCAS);
+ printf("%-50s %d-%d-%d-%d as DDR2-%d\n", "tCL-tRCD-tRP-tRAS",
+ highestCAS, trcd, trp, tras, ddrclk);
+ printf("%-50s %d.%d ns at CAS %d\n", "Minimum Cycle Time", x, y,
+ highestCAS);
+ printf("%-50s 0.%d%d ns at CAS %d\n", "Maximum Access Time",
+ (s->clk_access >> 4), (s->clk_access & 0xf), highestCAS);
+ printf("%-50s %d ns\n", "Maximum Cycle Time (tCK max)",
+ (s->tckmax >> 4) + (s->tckmax & 0x0f));
+
+ printf("\n---=== Timing Parameters ===---\n");
+ printf("%-50s 0.%d ns\n",
+ "Address/Command Setup Time Before Clock (tIS)",
+ funct(s->ca_setup));
+ printf("%-50s 0.%d ns\n", "Address/Command Hold Time After Clock (tIH)",
+ funct(s->ca_hold));
+ printf("%-50s 0.%d%d ns\n", "Data Input Setup Time Before Strobe (tDS)",
+ s->data_setup >> 4, s->data_setup & 0xf);
+ printf("%-50s 0.%d%d ns\n", "Data Input Hold Time After Strobe (tDH)",
+ s->data_hold >> 4, s->data_hold & 0xf);
+
+ printf("%-50s %d.%d ns\n", "Minimum Row Precharge Delay (tRP)",
+ integ(s->trp), des(s->trp));
+ printf("%-50s %d.%d ns\n",
+ "Minimum Row Active to Row Active Delay (tRRD)",
+ integ(s->trrd), des(s->trrd));
+ printf("%-50s %d.%d ns\n", "Minimum RAS# to CAS# Delay (tRCD)",
+ integ(s->trcd), des(s->trcd));
+ printf("%-50s %d ns\n", "Minimum RAS# Pulse Width (tRAS)",
+ ((s->tras & 0xfc) + (s->tras & 0x3)));
+ printf("%-50s %d.%d ns\n", "Write Recovery Time (tWR)",
+ integ(s->twr), des(s->twr));
+ printf("%-50s %d.%d ns\n", "Minimum Write to Read CMD Delay (tWTR)",
+ integ(s->twtr), des(s->twtr));
+ printf("%-50s %d.%d ns\n",
+ "Minimum Read to Pre-charge CMD Delay (tRTP)",
+ integ(s->trtp), des(s->trtp));
+ printf("%-50s %d ns\n", "Minimum Active to Auto-refresh Delay (tRC)",
+ s->trc);
+ printf("%-50s %d ns\n", "Minimum Recovery Delay (tRFC)", s->trfc);
+ printf("%-50s 0.%d ns\n", "Maximum DQS to DQ Skew (tDQSQ)", s->tdqsq);
+ printf("%-50s 0.%d ns\n", "Maximum Read Data Hold Skew (tQHS)",
+ s->tqhs);
+
+ printf("\n---=== Manufacturing Information ===---\n");
+
+ printf("%-50s", "Manufacturer JEDEC ID");
+ for (i = 64; i < 72; i++)
+ printf(" %02x", record[i]);
+
+ printf("\n");
+ if (s->mloc)
+ printf("%-50s 0x%02x\n", "Manufacturing Location Code",
+ s->mloc);
+
+ printf("%-50s ", "Part Number");
+ for (i = 73; i < 91; i++) {
+ if (record[i] >= 32 && record[i] < 127)
+ printf("%c", record[i]);
+ else
+ printf("%d", record[i]);
+ }
+ printf("\n");
+ printf("%-50s 20%d-W%d\n", "Manufacturing Date", record[93],
+ record[94]);
+ printf("%-50s 0x", "Assembly Serial Number");
+ for (i = 95; i < 99; i++)
+ printf("%02X", record[i]);
+}
diff --git a/include/ddr_spd.h b/include/ddr_spd.h
index fc03bac..01fe73c 100644
--- a/include/ddr_spd.h
+++ b/include/ddr_spd.h
@@ -228,6 +228,7 @@ struct ddr3_spd_eeprom_s {
uint8_t cust[80]; /* 176-255 Open for Customer Use */
};
+extern void ddr_spd_print(uint8_t *record);
extern uint32_t ddr3_spd_checksum_pass(const struct ddr3_spd_eeprom_s *spd);
extern uint32_t ddr2_spd_checksum_pass(const struct ddr2_spd_eeprom_s *spd);
--
2.1.4
More information about the barebox
mailing list