FC5 not properly configuring modem ofmultifunctionmodem/ethernet card

[Romano Giannetti]

On Tue, 2006-07-11 at 12:38 -0500, Stanley A. Klein wrote:

> At the suggestion of Jar, I tried copying the file to /lib/firmware.  
> It didn't work.  It looks like the file is not correct for the card I 
> have.  My card is a 3Com Corporation 3C562D/3C563D EtherLink III 
> LAN+Modem PC Card.  The information in the cis file that is related to 
> the dat is different than for my card.  Although they are both 3Com 
> multifunction LAN/modem cards, mine is an older model with different 
> product naming.
>
> What card do you have?

I have  a 3com/megahertz :
Socket 1:
  product info: "3Com", "Megahertz 3CXEM556 B", "LAN + 56k Modem", ""
  manfid: 0x0101, 0x0035

I have digged out and old dmesg from mandriva that worked:

[17179598.448000] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKA] ->
GSI 9 (level, low) -> IRQ 9
[17179598.448000] Yenta: CardBus bridge found at 0000:00:0a.0
[104d:80f6]
[17179598.448000] Yenta: Enabling burst memory read transactions
[17179598.448000] Yenta: Using CSCINT to route CSC interrupts to PCI
[17179598.448000] Yenta: Routing CardBus interrupts to PCI
[17179598.448000] Yenta TI: socket 0000:00:0a.0, mfunc 0x012c1222,
devctl 0x66
[17179598.680000] Yenta: ISA IRQ mask 0x0808, PCI irq 9
[17179598.680000] Socket status: 30000006
[17179598.692000] ACPI: PCI Interrupt 0000:00:0a.1[B] -> Link [LNKB] ->
GSI 10 (level, low) -> IRQ 10
[17179598.692000] Yenta: CardBus bridge found at 0000:00:0a.1
[104d:80f6]
[17179598.692000] Yenta: Using CSCINT to route CSC interrupts to PCI
[17179598.692000] Yenta: Routing CardBus interrupts to PCI
[17179598.692000] Yenta TI: socket 0000:00:0a.1, mfunc 0x012c1222,
devctl 0x66
[17179598.924000] Yenta: ISA IRQ mask 0x0808, PCI irq 10
[17179598.924000] Socket status: 30000010
[17179599.872000] cs: IO port probe 0xc00-0xcff: clean.
[17179599.872000] cs: IO port probe 0xc00-0xcff: clean.
[17179599.872000] cs: IO port probe 0x100-0x4ff: excluding 0x378-0x37f
0x4d0-0x4d7
[17179599.876000] cs: IO port probe 0x100-0x4ff: excluding 0x378-0x37f
0x4d0-0x4d7
[17179599.880000] cs: IO port probe 0xa00-0xaff: clean.
[17179599.880000] cs: IO port probe 0xa00-0xaff: clean.
[17179599.920000] cs: memory probe 0xa0000000-0xa0ffffff: clean.
[17179600.732000] eth1: 3Com 3c589, io 0x300, irq 3, hw_addr
00:00:86:1A:4E:A8
[17179600.732000]   8K FIFO split 5:3 Rx:Tx, auto xcvr
[17179600.776000] ttyS1 at I/O 0x2f8 (irq = 10) is a 16550A


and this is the one which is not working, with a recent kernel:

[17179598.628000] Yenta: CardBus bridge found at 0000:00:0a.0
[104d:80f6]
[17179598.628000] Yenta: Using CSCINT to route CSC interrupts to PCI
[17179598.628000] Yenta: Routing CardBus interrupts to PCI
[17179598.628000] Yenta TI: socket 0000:00:0a.0, mfunc 0x012c1222,
devctl 0x66
[17179598.788000] **** SET: Misaligned resource pointer: d961bb22 Type
07 Len 0
[17179598.788000] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
[17179598.788000] PCI: setting IRQ 5 as level-triggered
[17179598.788000] ACPI: PCI Interrupt 0000:00:07.5[C] -> Link [LNKC] ->
GSI 5 (level, low) -> IRQ 5
[17179598.788000] PCI: Setting latency timer of device 0000:00:07.5 to
64
[17179598.860000] Yenta: ISA IRQ mask 0x0808, PCI irq 9
[17179598.860000] Socket status: 30000068
[17179598.860000] ACPI: PCI Interrupt 0000:00:0a.1[B] -> Link [LNKB] ->
GSI 10 (level, low) -> IRQ 10
[17179598.860000] Yenta: CardBus bridge found at 0000:00:0a.1
[104d:80f6]
[17179598.860000] Yenta: Using CSCINT to route CSC interrupts to PCI
[17179598.860000] Yenta: Routing CardBus interrupts to PCI
[17179598.860000] Yenta TI: socket 0000:00:0a.1, mfunc 0x012c1222,
devctl 0x66
[17179598.940000] parport_pc: VIA parallel port: io=0x378, irq=7
[17179599.008000] Real Time Clock Driver v1.12
[17179599.092000] Yenta: ISA IRQ mask 0x0808, PCI irq 10
[17179599.092000] Socket status: 30000059
....
[17179600.324000] cs: IO port probe 0x100-0x3af: clean.
[17179600.324000] cs: IO port probe 0x3e0-0x4ff: clean.
[17179600.324000] cs: IO port probe 0x820-0x8ff: clean.
[17179600.328000] cs: IO port probe 0xc00-0xcf7: clean.
[17179600.328000] cs: IO port probe 0xa00-0xaff: clean.
[17179600.328000] cs: IO port probe 0x100-0x3af: clean.
[17179600.332000] cs: IO port probe 0x3e0-0x4ff: clean.
[17179600.332000] cs: IO port probe 0x820-0x8ff: clean.
[17179600.332000] cs: IO port probe 0xc00-0xcf7: clean.
[17179600.336000] cs: IO port probe 0xa00-0xaff: clean.
[17179600.336000] cs: memory probe 0xa0000000-0xa0ffffff: clean.
[17179600.340000] pcmcia: registering new device pcmcia1.0
[17179600.620000] rtl8180: Setting SW wep key
[17179600.724000] eth1: 3Com 3c589, io 0x300, irq 3, hw_addr
00:00:86:1A:4E:A8
[17179600.724000]   8K FIFO split 5:3 Rx:Tx, auto xcvr
...
[17180448.512000] pccard: card ejected from slot 1
[17180487.964000] pccard: PCMCIA card inserted into slot 1
[17180487.964000] pcmcia: registering new device pcmcia1.0
[17180488.016000] eth1: 3Com 3c589, io 0x300, irq 3, hw_addr
00:00:86:1A:4E:A8
[17180488.016000]   8K FIFO split 5:3 Rx:Tx, auto xcvr
[17180498.796000] eth1: no IPv6 routers present

and as you see the serial is not detected.
so... can anyone help me? Thanks!!!!

Romano



--
La presente comunicación tiene carácter confidencial y es para el exclusivo uso del destinatario indicado en la misma. Si Ud. no es el destinatario indicado, le informamos que cualquier forma de distribución, reproducción o uso de esta comunicación y/o de la información contenida en la misma están estrictamente prohibidos por la ley. Si Ud. ha recibido esta comunicación por error, por favor, notifíquelo inmediatamente al remitente contestando a este mensaje y proceda a continuación a destruirlo. Gracias por su colaboración.

This communication contains confidential information. It is for the exclusive use of the intended addressee. If you are not the intended addressee, please note that any form of distribution, copying or use of this communication or the information in it is strictly prohibited by law. If you have received this communication in error, please immediately notify the sender by reply e-mail and destroy this message. Thank you for your cooperation.