Problem with EPIA MII 10000 + NetGear WGT511T (Atheros based) or
D-Link DWL-650+ (ACX111 based)
Tal Rotbart
tal at netbox.com
Tue Jun 7 19:14:26 EDT 2005
Hi all,
I'm coming to the mailing list as the last resort as I've tried every solution I could find on the
web and then tried it again on various kernels: Debian Sarge (2.4 Kernel), DSL 1.1 (2.4 Kernel),
Knoppix 3.9 (2.6.11 kernel), Suse 9.2 (2.6.x kernel), Ubuntu (Hoary), etc. etc. to no avail and
utter frustration.
There is some weird interaction between the Ricoh PCMCIA bridge that is on the EPIA MII 10000 /
12000 bridge, that much is known. It causes the now infamous (on EPIA forums) problem of:
"PCI: Failed to allocate mem resource" errors.
However I've tried every suggested solutions, including:
1. Reserving the memory that failed to allocate using the boot parameters as mentioned here:
http://www.bfish.net/index.php?p=guide-epia
If I reserve the memory I can power up the card but no real communications with it at all. As if the
driver is writing to the memory location but nothing gets used by the card.
2. On 2.6 kernels I've tried adding 'override_bios=1" to the yenta_socket as suggested by Dominik
Brodowski in a message on this mailing list. See archived message:
http://lists.infradead.org/pipermail/linux-pcmcia/2005-January/001402.html
I'm afraid to report that this seemed to have absolutely no effect.
Note that of the D-Link DWL-650+ card I've even tried different cards of the same make, just in case
it was a faulty unit.
lspci and dmesg output attached, any clue would be greatly appreciated...
Tal
-------------- next part --------------
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8623 [Apollo CLE266]
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x4
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: dc000000-ddffffff
Prefetchable memory behind bridge: d8000000-dbffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0a.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80)
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 12
Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: de001000-de002000 (prefetchable)
Memory window 1: de003000-de004000
I/O window 0: 00009000-00009403
I/O window 1: 00009800-00009c03
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
0000:00:0a.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80)
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin B routed to IRQ 5
Region 0: Memory at de005000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: de006000-de007000 (prefetchable)
Memory window 1: de008000-de009000
I/O window 0: 0000a000-0000a403
I/O window 1: 0000a800-0000ac03
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:00:0d.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80) (prog-if 10 [OHCI])
Subsystem: VIA Technologies, Inc. IEEE 1394 Host Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at de00a000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at b000 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 12
Region 4: I/O ports at b400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at b800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin C routed to IRQ 5
Region 4: I/O ports at bc00 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin D routed to IRQ 12
Region 0: Memory at de00b000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 12
Region 4: I/O ports at c000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at c400 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded Ethernet Controller on VT8235
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 12
Region 0: I/O ports at cc00 [size=256]
Region 1: Memory at de00c000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:01:00.0 VGA compatible controller: VIA Technologies, Inc. VT8623 [Apollo CLE266] integrated CastleRock graphics (rev 03) (prog-if 00 [VGA])
Subsystem: VIA Technologies, Inc. VT8623 [Apollo CLE266] integrated CastleRock graphics
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min)
Interrupt: pin A routed to IRQ 12
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at dc000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
0000:02:00.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC (rev 01)
Subsystem: Netgear: Unknown device 4b00
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 12
Region 0: [virtual] Memory at de010000 (32-bit, non-prefetchable) [size=ffff5000]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
-------------- next part --------------
Linux version 2.6.11 (root at Knoppix) (gcc-Version 3.3.5 (Debian 1:3.3.5-12)) #2 SMP Thu May 26 20:53:11 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000dff0000 (usable)
BIOS-e820: 000000000dff0000 - 000000000dff3000 (ACPI NVS)
BIOS-e820: 000000000dff3000 - 000000000e000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
223MB LOWMEM available.
On node 0 totalpages: 57328
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 53232 pages, LIFO batch:12
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 VT9174 ) @ 0x000f6570
ACPI: RSDT (v001 VT9174 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0dff3000
ACPI: FADT (v001 VT9174 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0dff3040
ACPI: DSDT (v001 VT9174 AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
Allocating PCI resources starting at 0e000000 (gap: 0e000000:f1ff0000)
Built 1 zonelists
Kernel command line: ramdisk_size=100000 init=/etc/init lang=us apm=power-off vga=791 initrd=minirt.gz nomce quiet BOOT_IMAGE=knoppix BOOT_IMAGE=linux
__iounmap: bad address c00fffd9
No local APIC present or hardware disabled
mapped APIC to ffffd000 (012c2000)
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 999.937 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 221372k/229312k available (1847k kernel code, 7280k reserved, 946k data, 292k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1978.36 BogoMIPS (lpj=989184)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0380b03d 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 64K (32 bytes/line)
CPU: After all inits, caps: 0380b13d 00000000 00000000 00000000 00000000 0000003d 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
ACPI: setting ELCR to 0200 (from 1220)
CPU0: Centaur VIA Nehemiah stepping 04
per-CPU timeslice cutoff: 182.93 usecs.
task migration cache decay timeout: 1 msecs.
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
CPU0 attaching sched-domain:
domain 0: span 00000001
groups: 00000001
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 862k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfb2d0, last bus=3
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 4 5 6 7 *12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 4 5 6 7 12) *9
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 4 *5 6 7 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 4 5 6 7 *12)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas at hp.com
** so I can fix the driver.
pnp: 00:01: ioport range 0x400-0x47f could not be reserved
pnp: 00:01: ioport range 0x500-0x50f has been reserved
audit: initializing netlink socket (disabled)
audit(1118185808.626:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
vesafb: framebuffer at 0xd8000000, mapped to 0xce880000, using 3072k, total 32768k
vesafb: mode is 1024x768x16, linelength=2048, pages=20
vesafb: protected mode interface info at c000:7e96
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
mtrr: 0xd8000000,0x2000000 overlaps existing 0xd8000000,0x800000
mtrr: 0xd8000000,0x1000000 overlaps existing 0xd8000000,0x800000
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 12
PCI: setting IRQ 12 as level-triggered
ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [LNKA] -> GSI 12 (level, low) -> IRQ 12
PCI: Via PIC IRQ fixup for 0000:00:11.1, from 255 to 12
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xc000-0xc007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xc008-0xc00f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: Maxtor 6L160P0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: LITE-ON CD-RW SOHR-5239S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 1024KiB
hda: 320173056 sectors (163928 MB) w/8192KiB Cache, CHS=19929/255/63
hda: cache flushes supported
hda: hda1 hda2 hda3 < hda5 >
hdc: ATAPI 52X CD-ROM CD-R/RW drive, 1536kB Cache
Uniform CD-ROM driver Revision: 3.20
libata version 1.10 loaded.
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 16Kbytes
TCP established hash table entries: 8192 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 98304 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 15
ACPI wakeup devices:
PCI0 USB0 USB1 USB2 USB3 USB4 USB5 USB6 LAN0 AC97 MC97 UAR1
ACPI: (supports S0 S1 S4 S5)
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
seagate: ST0x/TMC-8xx not detected.
Failed initialization of WD-7000 SCSI card!
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 12
ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12
ehci_hcd 0000:00:10.3: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.3: irq 12, pci mem 0xde00b000
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.3: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 12 (level, low) -> IRQ 12
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:10.0: irq 12, io base 0xb400
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
PCI: Via PIC IRQ fixup for 0000:00:10.1, from 9 to 5
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:10.1: irq 5, io base 0xb800
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
uhci_hcd 0000:00:10.2: irq 5, io base 0xbc00
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ub: sizeof ub_scsi_cmd 64 ub_dev 2504
usbcore: registered new driver ub
Initializing USB Mass Storage driver...
usb 2-1: new low speed USB device using uhci_hcd and address 2
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1223 $ Ben Collins <bcollins at debian.org>
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
PCI: Via PIC IRQ fixup for 0000:00:0d.0, from 9 to 5
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[5] MMIO=[de00a000-de00a7ff] Max Packet=[2048]
sbp2: $Rev: 1219 $ Ben Collins <bcollins at debian.org>
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1)
usb 3-2: new full speed USB device using uhci_hcd and address 2
usb 3-2: device descriptor read/64, error -71
usb 3-2: device descriptor read/64, error -71
usb 3-2: new full speed USB device using uhci_hcd and address 3
usb 3-2: device descriptor read/64, error -71
usb 3-2: device descriptor read/64, error -71
ieee1394: Host added: ID:BUS[0-00:1023] GUID[004063500002d3a9]
Unable to identify CD-ROM format.
VFS: Can't find an ext2 filesystem on dev hda.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
cloop: Initializing cloop v2.02
cloop: loaded (max 8 devices)
cloop: /cdrom/KNOPPIX/KNOPPIX: 30729 blocks, 65536 bytes/block, largest block is 65552 bytes.
ISO 9660 Extensions: RRIP_1991A
Registering unionfs 052605-1143
Freeing unused kernel memory: 292k freed
Generic RTC Driver v1.07
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 2 throttling states)
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKA] -> GSI 12 (level, low) -> IRQ 12
Yenta: CardBus bridge found at 0000:00:0a.0 [1106:aa01]
Yenta: ISA IRQ mask 0x0c00, PCI irq 12
Socket status: 30000820
ACPI: PCI Interrupt 0000:00:0a.1[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
Yenta: CardBus bridge found at 0000:00:0a.1 [1106:aa01]
Yenta: ISA IRQ mask 0x0c00, PCI irq 5
Socket status: 30000006
PCI: Failed to allocate mem resource #0:10000 at de010000 for 0000:02:00.0
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.14.9 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413)
wlan: 0.8.4.5 (EXPERIMENTAL)
ath_rate_onoe: 1.0
ath_pci: 0.9.4.12 (EXPERIMENTAL)
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKA] -> GSI 12 (level, low) -> IRQ 12
ath_pci: cannot reserve PCI memory region
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x100-0x4ff: excluding 0x2f8-0x2ff 0x378-0x37f 0x3f8-0x47f 0x4d0-0x4d7
cs: IO port probe 0x100-0x4ff: excluding 0x2f8-0x2ff 0x378-0x37f 0x3f8-0x47f 0x4d0-0x4d7
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
usbcore: registered new driver hiddev
input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:10.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
ts: Compaq touchscreen protocol output
Serial: 8250/16550 driver $Revision: 1.90 $ 14 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
NET: Registered protocol family 23
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA CLE266 chipset
agpgart: Maximum main memory to use for agp memory: 176M
agpgart: AGP aperture is 128M @ 0xd0000000
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 12 (level, low) -> IRQ 12
eth0: VIA Rhine II at 0xde00c000, 00:40:63:da:65:4b, IRQ 12.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
Via 686a/8233/8235 audio driver 1.9.1-ac4-2.5
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
via82cxxx: Six channel audio available
PCI: Setting latency timer of device 0000:00:11.5 to 64
ac97_codec: AC97 Audio codec, id: ICE82 (Unknown)
via82cxxx: board #1 at 0xC400, IRQ 5
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
Adding 1052248k swap on /dev/hda2. Priority:-1 extents:1
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 17
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
mtrr: 0xd8000000,0x2000000 overlaps existing 0xd8000000,0x800000
atkbd.c: Unknown key pressed (translated set 2, code 0xbb on isa0060/serio0).
atkbd.c: Use 'setkeycodes e03b <keycode>' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xbb on isa0060/serio0).
atkbd.c: Use 'setkeycodes e03b <keycode>' to make it known.
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: disabled on user request.
More information about the linux-pcmcia
mailing list