Trouble whith TI PCI1620 cardbus resp. Compaq WL110 Wireless PC-Card
georg.fleischmann at online.de
georg.fleischmann at online.de
Mon Apr 11 17:38:01 EDT 2005
Hello,
I had some trouble with this cardbus, but i changed
/etc/pcmcia/config.options by using the memory range, which i found in
MS Windows.
Now it recognizes the PC-card when inserted, but i am not able to use it
and no light comes on.
When i start the cardmgr and insert the card i get this:
linux:/home/gf # tail -f /var/log/messages:
Apr 9 22:50:55 linux cardmgr[11092]: watching 2 sockets
Apr 9 22:50:55 linux kernel: cs: IO port probe 0x0c00-0x0cff: clean.
Apr 9 22:50:55 linux kernel: cs: IO port probe 0x0800-0x08ff: clean.
Apr 9 22:50:55 linux kernel: cs: IO port probe 0x0100-0x04ff: excluding
0x200-0x20f 0x4d0-0x4d7
Apr 9 22:51:09 linux cardmgr[11093]: socket 0: Compaq WL110 PC Card
Apr 9 22:51:10 linux kernel: orinoco 0.13e (David Gibson
<hermes at gibson.dropbear.id.au>, Pavel Roskin <proski at gnu.org>, et al)
Apr 9 22:51:10 linux kernel: orinoco_cs 0.13e (David Gibson
<hermes at gibson.dropbear.id.au>, Pavel Roskin <proski at gnu.org>, et al)
Apr 9 22:51:10 linux kernel: orinoco_cs: GetNextTuple(): No matching
CIS configuration, maybe you need the ignore_cis_vcc=1 parameter.
Apr 9 22:51:10 linux kernel: orinoco_cs: GetFirstTuple: No more items
Apr 9 22:51:11 linux cardmgr[11093]: get dev info on socket 0 failed:
Resourcetemporarily unavailable
linux:/home/gf # cardctl status
Socket 0:
5V 16-bit PC Card
function 0: [ready]
Socket 1:
no card
linux:/home/gf # cardctl ident
Socket 0:
product info: "Compaq", "Compaq WL110 PC Card", "Version 01.01", ""
manfid: 0x0156, 0x0002
function: 6 (network)
Socket 1:
no product info available
linux:/home/gf # dmesg | grep Yenta
Yenta: CardBus bridge found at 0000:02:04.0 [103c:006d]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x01111d22, devctl 0x64
Yenta: ISA IRQ mask 0x00f0, PCI irq 11
Yenta: CardBus bridge found at 0000:02:04.1 [103c:006d]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.1, mfunc 0x01111d22, devctl 0x64
Yenta: ISA IRQ mask 0x00f0, PCI irq 10
I was thinking about the power apply problem and tried setpci but since
i am not familiar to this, i dont know how to use that in the right
way. I just got this:
linux:/home/gf # setpci -s 04.0 0x80.1
Usage: setpci [<options>] (<device>+ <reg>[=<values>]*)*
linux:/home/gf # setpci -s 04.0 0x8000000
lspci: Register number out of range!
linux:/home/gf # setpci -s 04.0 0x8
01
linux:/home/gf # setpci -s 04.0 0x80
61
I am using this Machine:
Notebook: HP Compaq NX9105
Cardbus: TI PCI1620
PC-Card: Compaq WL110 Wireless
OS: SuSE 9.2 prof with kernel 2.6.8.-24.14
It would be great, if sombody may help me with my problem, i had a lot
of looking arround with google, but i couldn't solve it by myself.
Thanks for your Help
Georg Fleischmann
linux:/home/gf # lspci -vv
0000:00:00.0 Host bridge: nVidia Corporation nForce3 Host Bridge (rev
a4)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at f0000000 (32-bit, prefetchable)
Capabilities: [44] #08 [0180]
Capabilities: [c0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=x1
0000:00:01.0 ISA bridge: nVidia Corporation nForce3 LPC Bridge (rev a6)
Subsystem: nVidia Corporation: Unknown device 0c80
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:01.1 SMBus: nVidia Corporation nForce3 SMBus (rev a4)
Subsystem: Hewlett-Packard Company: Unknown device 006d
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 4: I/O ports at 2040 [size=64]
Region 5: I/O ports at 2000 [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.0 USB Controller: nVidia Corporation nForce3 USB 1.1 (rev a5)
(prog-if 10 [OHCI])
Subsystem: nVidia Corporation: Unknown device 0c80
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e8000000 (32-bit, non-prefetchable)
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.1 USB Controller: nVidia Corporation nForce3 USB 1.1 (rev a5)
(prog-if 10 [OHCI])
Subsystem: nVidia Corporation: Unknown device 0c80
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 10
Region 0: Memory at e8001000 (32-bit, non-prefetchable)
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.2 USB Controller: nVidia Corporation nForce3 USB 2.0 (rev a2)
(prog-if 20 [EHCI])
Subsystem: nVidia Corporation: Unknown device 0c80
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 10
Region 0: Memory at e8004000 (32-bit, non-prefetchable)
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:06.0 Multimedia audio controller: nVidia Corporation nForce3
Audio (rev a2)
Subsystem: Hewlett-Packard Company: Unknown device 006d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 1400
Region 1: I/O ports at 1c00 [size=128]
Region 2: Memory at e8002000 (32-bit, non-prefetchable)
[size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:06.1 Modem: nVidia Corporation: Unknown device 00d9 (rev a2)
(prog-if 00 [Generic])
Subsystem: Hewlett-Packard Company: Unknown device 006d
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: I/O ports at 1800
Region 1: I/O ports at 1c80 [size=128]
Region 2: Memory at e8003000 (32-bit, non-prefetchable)
[size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:08.0 IDE interface: nVidia Corporation nForce3 IDE (rev a5)
(prog-if 8a [Master SecP PriP])
Subsystem: nVidia Corporation: Unknown device 0c80
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Region 4: I/O ports at 2080 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0a.0 PCI bridge: nVidia Corporation nForce3 PCI Bridge (rev a2)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=0a, sec-latency=128
I/O behind bridge: 00003000-00007fff
Memory behind bridge: e8100000-e97fffff
Expansion ROM at 00003000 [disabled] [size=20K]
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
0000:00:0b.0 PCI bridge: nVidia Corporation nForce3 AGP Bridge (rev a4)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Bus: primary=00, secondary=01, subordinate=01, sec-latency=10
Memory behind bridge: ea000000-eaffffff
Prefetchable memory behind bridge: f8000000-fc0fffff
BridgeCtl: Parity+ SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] #08 [2101]
0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:01:00.0 VGA compatible controller: nVidia Corporation NV17
[GeForce4 420 Go 32M] (rev a3) (prog-if 00 [VGA])
Subsystem: Hewlett-Packard Company: Unknown device 006d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ea000000 (32-bit, non-prefetchable)
Region 1: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Region 2: Memory at fc000000 (32-bit, prefetchable) [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64-
HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
0000:02:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21
IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company: Unknown device 006d
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max), cache line size 10
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e8106000 (32-bit, non-prefetchable)
Region 1: Memory at e8100000 (32-bit, non-prefetchable)
[size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
0000:02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 7000
Region 1: Memory at e8106800 (32-bit, non-prefetchable)
[size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:04.0 CardBus bridge: Texas Instruments PCI1620 PC Card
Controller (rev 01)
Subsystem: Hewlett-Packard Company: Unknown device 006d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 20
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e8104000 (32-bit, non-prefetchable)
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: e8200000-e83ff000 (prefetchable)
Memory window 1: e8400000-e85ff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+
PostWrite+
16-bit legacy interface ports at 0001
0000:02:04.1 CardBus bridge: Texas Instruments PCI1620 PC Card
Controller (rev 01)
Subsystem: Hewlett-Packard Company: Unknown device 006d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 20
Interrupt: pin B routed to IRQ 10
Region 0: Memory at e8105000 (32-bit, non-prefetchable)
Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
Memory window 0: e9000000-e93ff000 (prefetchable)
Memory window 1: e8c00000-e8fff000
I/O window 0: 00006000-00006fff
I/O window 1: 00005000-00005fff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+
PostWrite+
16-bit legacy interface ports at 0001
0000:02:04.2 System peripheral: Texas Instruments PCI1620 Firmware
Loading Function (rev 01)
Subsystem: Hewlett-Packard Company: Unknown device 006d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1750ns min, 1000ns max), cache line size 10
Region 0: I/O ports at 7400
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
More information about the linux-pcmcia
mailing list