[Fwd: irq 9: nobody cared! after moving from 2.4.19 to 2.6.11.5]
Scott Waye
scott at waye.co.uk
Mon Apr 11 04:15:11 EDT 2005
Hi,
I've been following the thread
Re: Bug#270376: PCMCIA Nic stops working after upgrading to 2.6.6/7/8
as I have also been having problems with
my PCMCIA card (actually I think its a Cardbus card, but I'm not sure)
since moving from 2.4.19 to 2.6.8.1.
With 2.6.8.1 the machine (a Sony Vaio Laptop FX401 (PCG972-M) with a
belkin 802.11b (atmelwlan driver) would boot ok, but X11 would crash the
kernel if the card was enabled. Workaround there was to cardctl eject
0, start X11, cardctl insert 0. That normally worked. I then upgraded
to 2.6.11.5 with and without the recently posted TI patch from the above thread and now the network
connection does not come up properly even without X.
On booting with the patch and with the card inserted, dmesg reports this and lspci -vv
follows the dmesg output
After booting the card power led is on, and the activity led is on continuously (normally flashes) and
dmesg logs "interface not ready yet" repeatedly.
Not sure if its relevant, but you'll notice that I have lapic in the kernel options (the only option) as
without it I get a message like "APIC disabled by the BIOS, enable with "lapic"
Linux version 2.6.11.5 (root at cali) (gcc version 3.2) #4 Sun Apr 10
09:39:43 BST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000c0000 - 00000000000d4000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fef0000 (usable)
BIOS-e820: 000000000fef0000 - 000000000feff000 (ACPI data)
BIOS-e820: 000000000feff000 - 000000000ff00000 (ACPI NVS)
BIOS-e820: 000000000ff00000 - 0000000010000000 (usable)
BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved)
256MB LOWMEM available.
On node 0 totalpages: 65536
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61440 pages, LIFO batch:15
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f7700
ACPI: RSDT (v001 SONY K5 0x06040000 LTP 0x00000000) @ 0x0fef9d89
ACPI: FADT (v001 SONY K5 0x06040000 PTL_ 0x000f4240) @ 0x0fefee4c
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x0fefeec0
ACPI: SSDT (v001 PTLTD POWERNOW 0x06040000 LTP 0x00000001) @ 0x0fefeee8
ACPI: DSDT (v001 SONY K5 0x06040000 MSFT 0x0100000d) @ 0x00000000
Allocating PCI resources starting at 10000000 (gap: 10000000:effe0000)
Built 1 zonelists
Kernel command line: BOOT_IMAGE=Linux ro root=306 lapic
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
mapped APIC to ffffd000 (fee00000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 800.191 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 255840k/262144k available (2076k kernel code, 5680k reserved,
834k data, 148k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1572.86 BogoMIPS (lpj=786432)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff c1c7fbff 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c7fbff 00000000 00000000
00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 64K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c7fbff 00000000 00000020 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD mobile AMD Duron(tm) stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
tbxface-0118 [02] acpi_load_tables : ACPI Tables successfully acquired
Parsing all Control
Methods:.................................................................................................................................................................
Table [DSDT](id F005) - 562 Objects with 44 Devices 161 Methods 22 Regions
Parsing all Control Methods:
Table [SSDT](id F003) - 3 Objects with 0 Devices 0 Methods 0 Regions
ACPI Namespace successfully loaded at root c040e3c0
ACPI: setting ELCR to 0200 (from 0620)
evxfevnt-0094 [03] acpi_enable : Transition to ACPI mode
successful
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd7cd, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
evgpeblk-0979 [06] ev_create_gpe_block : GPE 00 to 0F [_GPE] 2 regs on
int 0x9
evgpeblk-0987 [06] ev_create_gpe_block : Found 2 Wake, Enabled 1
Runtime GPEs in this block
Completing Region/Field/Buffer/Package
initialization:..........................................................................................
Initialized 22/22 Regions 16/16 Fields 27/27 Buffers 25/27 Packages (574
nodes)
Executing all Device _STA and_INI
methods:................................................
48 Devices found containing: 48 _STA, 3 _INI methods
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Via IRQ fixup
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *9 10 11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 *10 11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 9 10 11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *9 10 11 12)
ACPI: Embedded Controller [EC0] (gpe 1)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PPB_._PRT]
ACPI: Power Resource [PCR0] (off)
ACPI: Power Resource [PCR1] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
Linux Kernel Card Services
options: [pci] [cardbus]
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas at hp.com
** so I can fix the driver.
Simple Boot Flag at 0x37 set to 0x1
Applying VIA southbridge workaround.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
hda: HITACHI_DK23CA-15, ATA DISK drive
Probing IDE interface ide1...
hdc: QSI DVD-ROM SDR-081, ATAPI CD/DVD-ROM drive
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
spurious 8259A interrupt: IRQ7.
[ACPI Debug] String: [0x1C] "Temperature increasing: _Q80"
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 29498112 sectors (15103 MB) w/512KiB Cache, CHS=29264/16/63
hda: cache flushes not supported
hda: hda1 hda2 < hda5 hda6 >
hdc: ATAPI 24X DVD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.20
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 9 (level, low) -> IRQ 9
Yenta: CardBus bridge found at 0000:00:0a.0 [104d:80f6]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0a.0, mfunc 0x012c1222, devctl 0x66
irq 9: nobody cared!
[<c013022a>] __report_bad_irq+0x2a/0x90
[<c012fb20>] handle_IRQ_event+0x30/0x70
[<c013031c>] note_interrupt+0x6c/0xd0
[<c012fcae>] __do_IRQ+0x14e/0x160
[<c01044a3>] do_IRQ+0x23/0x40
[<c0102a3a>] common_interrupt+0x1a/0x20
[<c0119ab0>] __do_softirq+0x30/0x90
[<c0119b36>] do_softirq+0x26/0x30
[<c0119c15>] irq_exit+0x35/0x40
[<c01044a8>] do_IRQ+0x28/0x40
[<c0102a3a>] common_interrupt+0x1a/0x20
[<c01111d9>] sub_preempt_count+0x39/0x60
[<c01e659f>] pci_bus_write_config_word+0x7f/0xa0
[<c027b59c>] yenta_probe_cb_irq+0x7c/0x130
[<c0114f67>] printk+0x17/0x20
[<c027a4ef>] ti12xx_irqroute_func0+0x8f/0x380
[<c027ad11>] ti12xx_override+0x101/0x1a0
[<c027ba67>] yenta_probe+0x237/0x250
[<c01ea532>] pci_device_probe_static+0x52/0x70
[<c01ea58c>] __pci_device_probe+0x3c/0x50
[<c01ea5cc>] pci_device_probe+0x2c/0x50
[<c023dcef>] driver_probe_device+0x2f/0x70
[<c023de29>] driver_attach+0x59/0x90
[<c023e2f8>] bus_add_driver+0x98/0xd0
[<c023e91f>] driver_register+0x2f/0x40
[<c025a11c>] ide_register_driver+0x10c/0x130
[<c01ea842>] pci_register_driver+0x62/0x80
[<c03f206f>] yenta_socket_init+0xf/0x20
[<c03da81b>] do_initcalls+0x2b/0xc0
[<c03f37aa>] sock_init+0x2a/0x40
[<c01002c0>] init+0x0/0x110
[<c01002ef>] init+0x2f/0x110
[<c010086c>] kernel_thread_helper+0x0/0x14
[<c0100871>] kernel_thread_helper+0x5/0x14
handlers:
[<c01f01d0>] (acpi_irq+0x0/0x16)
Disabling IRQ #9
[ACPI Debug] String: [0x24] "------------------------ _Q09 : test"
Yenta TI: socket 0000:00:0a.0 probing PCI interrupt failed, trying to fix
Yenta TI: socket 0000:00:0a.0 falling back to parallel PCI interrupts
Yenta TI: socket 0000:00:0a.0 no PCI interrupts. Fish. Please report.
Yenta: ISA IRQ mask 0x0c00, PCI irq 0
Socket status: 30000019
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI interrupt 0000:00:0a.1[B] -> GSI 10 (level, low) -> IRQ 10
Yenta: CardBus bridge found at 0000:00:0a.1 [104d:80f6]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0a.1, mfunc 0x012c1222, devctl 0x64
Yenta TI: socket 0000:00:0a.1 probing PCI interrupt failed, trying to fix
Yenta TI: socket 0000:00:0a.1 no PCI interrupts. Fish. Please report.
Yenta: ISA IRQ mask 0x0808, PCI irq 0
Socket status: 30000006
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
ALPS Touchpad (Glidepoint) detected
Disabling hardware tapping
input: AlpsPS/2 ALPS TouchPad on isa0060/serio1
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
NET: Registered protocol family 1
NET: Registered protocol family 17
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 148k freed
kjournald starting. Commit interval 5 seconds
Adding 265032k swap on /dev/hda5. Priority:-1 extents:1
EXT3 FS on hda6, internal journal
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0x100-0x4ff: excluding 0x378-0x37f 0x3f8-0x3ff 0x4d0-0x4d7
cs: IO port probe 0x100-0x4ff: excluding 0x378-0x37f 0x3f8-0x3ff 0x4d0-0x4d7
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
pcmf502re: ATMEL 11Mbps Wireless PCMCIA LAN driver version 2.0.1.0
-> vnet_attach()
-> vnet_event(registration complete, 0, 0xc0115074)
-> vnet_event(card insertion, 0, 0xc0115074)
-> vnet_config(0x00000000)
pcmf502re: index 0x01: Vcc 5.0, irq 10, io 0x0100-0x011f
pcmf502re: Registered netdevice atml0
Copy Code To Internal Memory (** EEPROM **)
*** Downloading Firmware to internal memory ***
--=+>GetFwFile BasicFW : 35348,
Fw Mapped in : 0xCF370000
<=- Out of GetFwFile
**** SCATTER LOADING ****
... atmelwlan debug messages deleted
Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI interrupt 0000:00:07.5[C] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:07.5 to 64
interface not ready yet
interface not ready yet
interface not ready yet
interface not ready yet
interface not ready yet
interface not ready yet
interface not ready yet
interface not ready yet
interface not ready yet
interface not ready yet
interface not ready yet
interface not ready yet
interface not ready yet
interface not ready yet
interface not ready yet
interface not ready yet
interface not ready yet
interface not ready yet
00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 0305 (rev 03)
Subsystem: Sony Corporation: Unknown device 80f6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR+
Latency: 8
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc.: Unknown device 8305 (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: e8100000-e9ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super] (rev 40)
Subsystem: Sony Corporation: Unknown device 80f6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev
06) (prog-if 8a [Master SecP PriP])
Subsystem: Sony Corporation: Unknown device 80f6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 4: I/O ports at 1c40 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.2 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 1a)
(prog-if 00 [UHCI])
Subsystem: Sony Corporation: Unknown device 80f6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, cache line size 08
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at 1c00 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.3 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 1a)
(prog-if 00 [UHCI])
Subsystem: Sony Corporation: Unknown device 80f6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, cache line size 08
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at 1c20 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.4 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
(rev 40)
Subsystem: Sony Corporation: Unknown device 80f6
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686
[Apollo Super AC97/Audio] (rev 50)
Subsystem: Sony Corporation: Unknown device 80f6
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at 1000 [size=256]
Region 1: I/O ports at 1c54 [size=4]
Region 2: I/O ports at 1c50 [size=4]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.6 Communication controller: VIA Technologies, Inc. VT82C686
[Apollo Super AC97/Modem] (rev 30)
Subsystem: Sony Corporation: Unknown device 80f6
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at 1400 [size=256]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 CardBus bridge: Texas Instruments PCI1420
Subsystem: Sony Corporation: Unknown device 80f6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 10
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:0a.1 CardBus bridge: Texas Instruments PCI1420
Subsystem: Sony Corporation: Unknown device 80f6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 10
Interrupt: pin B routed to IRQ 10
Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 10c00000-10fff000 (prefetchable)
Memory window 1: 11000000-113ff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00:0e.0 FireWire (IEEE 1394): Texas Instruments: Unknown device 8020
(prog-if 10 [OHCI])
Subsystem: Sony Corporation: Unknown device 80f6
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 9
Region 0: Memory at e8004000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at e8000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139
(rev 10)
Subsystem: Sony Corporation: Unknown device 80f6
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 1800 [size=256]
Region 1: Memory at e8004800 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage P/M
Mobility AGP 2x (rev 64) (prog-if 00 [VGA])
Subsystem: Sony Corporation: Unknown device 80f6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: Memory at e9000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at e8100000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [50] AGP version 1.0
Status: RQ=255 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [5c] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
More information about the linux-pcmcia
mailing list