[PATCH v6 5/5] ARM: dts: sun9i: Initial support for the Sunchip CX-A99 board
Chen-Yu Tsai
wens at csie.org
Fri Feb 10 01:22:21 PST 2017
On Fri, Feb 10, 2017 at 4:59 PM, Maxime Ripard
<maxime.ripard at free-electrons.com> wrote:
> Hi,
>
> On Thu, Feb 09, 2017 at 12:34:06AM +0100, Rask Ingemann Lambertsen wrote:
>> The Suncip CX-A99 board is found in at least four brands of media players.
>> It features an Allwinner A80 ARM SoC and is found in two models:
>>
>> 1) 2 GiB DDR3 DRAM and 16 GB eMMC
>> 2) 4 GiB DDR3 DRAM and 32 GB eMMC
>>
>> For details of the board, see the linux-sunxi page
>> <URL:https://linux-sunxi.org/Sunchip_CX-A99>.
>
> Please don't put URLs in commit logs (and the DT).
>
>>
>> Supported features (+ means tested):
>> + One Cortex-A7 CPU core (or four with experimental U-Boot PSCI patches)
>> + AXP808 power management chip
>> + OZ80120 voltage regulator
>> + Serial console port (internal)
>> + eMMC and SD card slot
>> + USB 2.0 host ports on on-board USB hub
>> + SATA port on on-board SATA-to-USB bridge *
>> + IEEE 802.11 a/b/g/n/ac SDIO Wifi
>> + Real-time clock
>> + LEDs
>> - IR receiver for remote control
>>
>> * Only shows up when a SATA device is connected. Also, if a power source
>> is connected to the USB 3.0 connector across power cycles (e.g. FEL
>> boot), the bridge may not properly reset and not show up on the USB bus.
>> The vendor U-Boot performs some unknown magic which resets the bridge.
>
> Is that magic at the USB level, or specific to the bridge itself?
>
>> So far unsupported features:
>> - Using any of the Cortex-A15 CPU cores
>> - USB 3.0 port (except for supplying 5 V power)
>> - IEEE 802.3 10/100/1000 megabit Ethernet
>> - HDMI connector
>> - S/PDIF audio output
>> - Jack socket with composite video and analog stereo audio
>> - Bluetooth
>> - FM radio receiver (assuming it is even wired on the board)
>
> I guess that should be in your cover letter.
>
> This is not found in your DT, so no one really expects it to work :)
>
>> Signed-off-by: Rask Ingemann Lambertsen <rask at formelder.dk>
>> ---
>>
>> Changes in v6:
>> - Updated commit message description of SATA-to-USB bridge quirk and added
>> note about experimental U-Boot PSCI support for up to four CPU cores.
>> - The blue LED is no longer on by default as its meaning is not documented.
>> - Removed "regulator-boot-on" from regulators having "regulator-always-on".
>> - Removed misleading mention of "OTG connector" which the device doesn't have.
>> - More detailed explanation for the need for "broken-cd" on mmc0.
>> - Several regulators have had their voltage range relaxed a little to match
>> the permissible range according to the data sheets of the consumers. This
>> is similar to what is used for the Cubieboard4 and Merrii A80 Optimus.
>> - Shortened regulator dcdce name as per v5 comments. A comment now lists the
>> pin groups supplied by dcdce.
>>
>> Changes in v5:
>> - Switched pinmux modes to generic properties and dropped
>> #include <dt-bindings/pinctrl/sun4i-a10.h> as a consequence.
>> - Dropped pinctrl properties from GPIO nodes and dropped the pinmux
>> nodes for them.
>> - AXP808 regulators added.
>> - Dropped the now unused #include <sunxi-common-regulators.dtsi>.
>> - Ampak AP6335 SDIO-Wifi added.
>> - USB Vbus changes as per v4 comments.
>> - Added "broken-cd" to mmc0 because GPIO interrupts don't work.
>>
>> Changes in v4:
>> - Node names had underscores changed to hyphens.
>> - Changed formatting of the ac100/rtc node's clock output name list to match
>> that of the same node in the cubieboard4 and a80-optimus device trees.
>>
>> Changes in v3:
>> None.
>>
>> Changes in v2:
>> - Fixed formatting and style issues found by scripts/checkpatch.pl.
>>
>> arch/arm/boot/dts/Makefile | 3 +-
>> arch/arm/boot/dts/sun9i-a80-cx-a99.dts | 409 +++++++++++++++++++++++++++++++++
>> 2 files changed, 411 insertions(+), 1 deletion(-)
>> create mode 100644 arch/arm/boot/dts/sun9i-a80-cx-a99.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index 8553bd7..40546fa 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -862,7 +862,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \
>> sun8i-v3s-licheepi-zero.dtb
>> dtb-$(CONFIG_MACH_SUN9I) += \
>> sun9i-a80-optimus.dtb \
>> - sun9i-a80-cubieboard4.dtb
>> + sun9i-a80-cubieboard4.dtb \
>> + sun9i-a80-cx-a99.dtb
>> dtb-$(CONFIG_ARCH_TANGO) += \
>> tango4-vantage-1172.dtb
>> dtb-$(CONFIG_ARCH_TEGRA_2x_SOC) += \
>> diff --git a/arch/arm/boot/dts/sun9i-a80-cx-a99.dts b/arch/arm/boot/dts/sun9i-a80-cx-a99.dts
>> new file mode 100644
>> index 0000000..f5496d2
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun9i-a80-cx-a99.dts
>> @@ -0,0 +1,409 @@
>> +/*
>> + * sun9i-a80-cx-a99.dts - Device Tree file for the Sunchip CX-A99 board.
>> + *
>> + * Copyright (C) 2017 Rask Ingemann Lambertsen <rask at formelder.dk>
>> + *
>> + * This file is dual-licensed: you can use it either under the terms
>> + * of the GPL or the X11 license, at your option. Note that this dual
>> + * licensing only applies to this file, and not this project as a
>> + * whole.
>> + *
>> + * a) This file is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of the
>> + * License, or (at your option) any later version.
>> + *
>> + * This file is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + *
>> + * Or, alternatively,
>> + *
>> + * b) Permission is hereby granted, free of charge, to any person
>> + * obtaining a copy of this software and associated documentation
>> + * files (the "Software"), to deal in the Software without
>> + * restriction, including without limitation the rights to use,
>> + * copy, modify, merge, publish, distribute, sublicense, and/or
>> + * sell copies of the Software, and to permit persons to whom the
>> + * Software is furnished to do so, subject to the following
>> + * conditions:
>> + *
>> + * The above copyright notice and this permission notice shall be
>> + * included in all copies or substantial portions of the Software.
>> + *
>> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
>> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
>> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
>> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>> + * OTHER DEALINGS IN THE SOFTWARE.
>> + */
>> +
>> +/*
>> + * The Sunchip CX-A99 board is found in several similar Android media
>> + * players, such as:
>> + *
>> + * Instabox Fantasy A8 (no external antenna)
>> + * Jesurun CS-Q8 (ships with larger remote control)
>> + * Jesurun Maxone
>> + * Rikomagic (RKM) MK80/MK80LE
>> + * Tronsmart Draco AW80 Meta/Telos
>> + *
>> + * See <URL:https://linux-sunxi.org/Sunchip_CX-A99> for more information.
>> + */
>> +
>> +/dts-v1/;
>> +#include "sun9i-a80.dtsi"
>> +
>> +#include <dt-bindings/gpio/gpio.h>
>> +
>> +/ {
>> + model = "Sunchip CX-A99";
>> + compatible = "sunchip,cx-a99", "allwinner,sun9i-a80";
>> +
>> + aliases {
>> + serial0 = &uart0;
>> + };
>> +
>> + chosen {
>> + stdout-path = "serial0:115200n8";
>> + };
>> +
>> + leds {
>> + compatible = "gpio-leds";
>> +
>> + blue {
>> + gpios = <&pio 6 10 GPIO_ACTIVE_HIGH>; /* PG10 */
>> + label = "cx-a99:blue:status";
>> + };
>> +
>> + red {
>> + gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
>> + label = "cx-a99:red:status";
>> + };
>> + };
>> +
>> + powerseq_wifi: powerseq-wifi {
>> + compatible = "mmc-pwrseq-simple";
>> + clocks = <&ac100_rtc 1>;
>> + clock-names = "ext_clock";
>> + reset-gpios = <&r_pio 1 0 GPIO_ACTIVE_LOW>; /* PM0 */
>> + post-power-on-delay-ms = <1>; /* Minimum 2 cycles. */
>> + };
>> +
>> + /* USB 3.0 standard-A receptacle. For now, only Vbus is supported. */
>
> I'm not sure what you mean by "only VBUS is supported"? Is there any
> other signal?
>
>> + reg_usb0_vbus: regulator-usb0-vbus {
>> + compatible = "regulator-fixed";
>> + regulator-name = "usb0-vbus";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + gpio = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
>> + enable-active-high;
>
> This is redundant with the GPIO flag
>
>> + regulator-always-on;
>
> And it shouldn't be always on. The USB driver will enable it if needs
> be.
>
>> + };
>> +
>> + /*
>> + * A GL850G hub with two external USB connectors is connected
>> + * to ehci0. Each has a Vbus regulator controlled by a GPIO:
>> + * PL7 for port 1, closest to the 12 V power connector, and
>> + * PL8 for port 2, next to the SD card slot.
>> + * Because regulator-fixed doesn't support a GPIO list, and
>> + * allwinner,sun9i-a80-usb-phy doesn't support more than one
>> + * supply, we have to use regulator-always-on on usb1-2-vbus.
>> + * Note that the GPIO pins also need cldo1 to be enabled.
>> + */
>
> What is the source of those regulators connected then? Some PMIC
> regulator? AC-IN?
>
>> + reg_usb1_1_vbus: regulator-usb1-1-vbus {
>> + compatible = "regulator-fixed";
>> + regulator-name = "usb1-1-vbus";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + gpio = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */
>> + enable-active-high;
>> + };
>> +
>> + reg_usb1_2_vbus: regulator-usb1-2-vbus {
>> + compatible = "regulator-fixed";
>> + regulator-name = "usb1-2-vbus";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
>> + enable-active-high;
>> + regulator-always-on;
>
> Same comment about always on. If the driver needs fixing to grab an
> additional regulator, fix it, but this shouldn't be left that way.
>
>> + };
>> +
>> + /* OZ80120 voltage regulator for the four Cortex-A15 cores. */
>> + reg_vdd_cpub: regulator-vdd-cpub {
>> + compatible = "regulator-gpio";
>> +
>> + regulator-always-on;
>> + regulator-min-microvolt = < 800000>;
>> + regulator-max-microvolt = <1100000>;
>> + regulator-name = "vdd-cpub";
>> +
>> + enable-gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
>> + enable-active-high;
>> + gpios = <&r_pio 0 3 GPIO_ACTIVE_HIGH>, /* PL3 */
>> + <&r_pio 0 4 GPIO_ACTIVE_HIGH>, /* PL4 */
>> + <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */
>> +
>> + gpios-states = <1 0 0>;
>> + states = < 750000 0x7
>> + 800000 0x3
>> + 850000 0x5
>> + 900000 0x1
>> + 950000 0x6
>> + 1000000 0x2
>> + 1100000 0x4
>> + 1200000 0x0>;
>
> You're listing a minimum state of 750mv, yet your minimum voltage is
> 800mV.
>
>> + };
>> +};
>> +
>> +&ehci0 {
>> + status = "okay";
>> +};
>> +
>> +&ehci2 {
>> + status = "okay";
>> +};
>> +
>> +/*
>> + * SD card slot. Although the GPIO pin for card detection is listed as capable
>> + * of generating interrupts in the "A80 User Manual", this doesn't work for
>> + * some unknown reason, so poll the GPIO for card detection. This is also what
>> + * the vendor sys_config.fex file specifies.
>> + */
>> +&mmc0 {
>> + bus-width = <4>;
>> + cd-gpios = <&pio 7 17 GPIO_ACTIVE_LOW>; /* PH17 */
>> + broken-cd; /* Poll. */
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mmc0_pins>;
>> + vmmc-supply = <®_dcdce>;
>> + status = "okay";
>> +};
>> +
>> +/* Ampak AP6335 IEEE 802.11 a/b/g/n/ac "Wifi". */
>
> Why "wifi" ? It's not implementing true wifi?
>
>> +&mmc1 {
>> + bus-width = <4>;
>> + non-removable;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mmc1_pins>;
>> + vmmc-supply = <®_cldo3>; /* See cldo2,cldo3 note. */
>> + vqmmc-supply = <®_aldo2>;
>
> So it's able to support 1.2 or 1.8V IO modes? Surely you want to
> enable those modes here to.
>
>> + mmc-pwrseq = <&powerseq_wifi>;
>> + status = "okay";
>> +};
>> +
>> +/* On-board eMMC card. */
>> +&mmc2 {
>> + bus-width = <8>;
>> + non-removable;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mmc2_8bit_pins>;
>> + vmmc-supply = <®_dcdce>;
>> + status = "okay";
>> +};
>> +
>> +&osc32k {
>> + clocks = <&ac100_rtc 0>;
>> +};
>> +
>> +&r_ir {
>> + status = "okay";
>> +};
>> +
>> +&r_rsb {
>> + status = "okay";
>> +
>> + ac100: codec at e89 {
>> + compatible = "x-powers,ac100";
>> + reg = <0xe89>;
>> +
>> + ac100_codec: codec {
>> + compatible = "x-powers,ac100-codec";
>> + interrupt-parent = <&r_pio>;
>> + interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>; /* PL9 */
>> + #clock-cells = <0>;
>> + clock-output-names = "4M_adda";
>> + };
>> +
>> + ac100_rtc: rtc {
>> + compatible = "x-powers,ac100-rtc";
>> + interrupt-parent = <&nmi_intc>;
>> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
>> + clocks = <&ac100_codec>;
>> + #clock-cells = <1>;
>> + clock-output-names = "cko1_rtc",
>> + "cko2_rtc",
>> + "cko3_rtc";
>> + };
>> + };
>> +
>> + pmic at 745 {
>> + compatible = "x-powers,axp808", "x-powers,axp806";
As you mentioned elsewhere, they are not really compatible.
You should drop the latter compatible.
>> + reg = <0x745>;
>> + interrupt-parent = <&nmi_intc>;
>> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
>> + interrupt-controller;
>> + #interrupt-cells = <1>;
>> +
>> + swin-supply = <®_dcdce>;
>
> Please use an incude for that PMIC.
Hmm, there isn't one for the AXP806 either.
Some more info about the regulator names:
>> +
>> + /* In comments: Initial setup from vendor sys_config.fex. */
>> + regulators {
>> + /* 3.0 V (enabled). */
>
> This might be disabled though.
>
>> + reg_aldo1: aldo1 {
>> + regulator-boot-on;
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <3000000>;
>> + regulator-name = "vcc-3v0";
>> + };
>> +
>> + /* 1.8 V (enabled). */
>> + reg_aldo2: aldo2 {
>> + regulator-boot-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <3600000>;
>> + regulator-name = "vcc-pg-pm-wifi+btio-audio";
>
> Usually, there is simpler names available on the schematics, or at
> least simpler names we can come up with.
>
> Something like vcc-wifi would be enough her.
It should be vddio-wifi. Looking at the pin groups it names, it likely
just drives the I/O pins on both ends.
>
>> + };
>> +
>> + /* 2.5 V (enabled). */
>> + reg_aldo3: aldo3 {
>> + regulator-boot-on;
>> + regulator-min-microvolt = <2500000>;
>> + regulator-max-microvolt = <2500000>;
>> + regulator-name = "vcc-pa-gmac2v5";
>
> vcc-gmac
vcc-pa or vddio-gmac. 2.5V is for RGMII I/O. vcc-gmac is the "sw"
regulator @ 3.3V.
>
>> + };
>> +
>> + /* 1.8 V (enabled). */
>> + reg_bldo1: bldo1 {
>> + regulator-always-on; /* Hang if disabled */
>> + regulator-min-microvolt = <1700000>;
>> + regulator-max-microvolt = <1900000>;
>> + regulator-name = "vdd18-dll-vcc18-pll";
>
> vdd-dll
PLLs and DLLs are different though. Maybe vcc-pll-dll?
>
>> + };
>> +
>> + /* 0.9 V (enabled). */
>> + reg_bldo2: bldo2 {
>> + regulator-always-on; /* Hang if disabled */
>> + regulator-min-microvolt = < 800000>;
>> + regulator-max-microvolt = <1100000>;
>> + regulator-name = "vdd-cpus";
>> + };
>> +
>> + /* 1.2 V (disabled). */
>> + reg_bldo3: bldo3 {
>> + regulator-min-microvolt = <1100000>;
>> + regulator-max-microvolt = <1300000>;
>> + regulator-name = "vcc12-hsic";
>
> vcc-hsic
vcc12-hsic is actually the name listed in the SoC datasheet.
>
>> + };
>> +
>> + /* 1.1 V (enabled). */
>> + reg_bldo4: bldo4 {
>> + regulator-boot-on;
>> + regulator-min-microvolt = < 800000>;
>> + regulator-max-microvolt = <1100000>;
>> + regulator-name = "vdd09-hdmi";
>
> vdd-hdmi
vdd09-hdmi is actually the name listed in the SoC datasheet.
>
>> + };
>> +
>> + /* 3.3 V (enabled). PLx pins control some regulators. */
>> + reg_cldo1: cldo1 {
>> + regulator-always-on;
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-name = "vcc-pl-led";
>
> vcc-led, etc...
vcc-pl is probably better... One can figure out the LEDs are connected to the
PL group and maybe realize they are powered this way. Not that easy the other
way around.
I used really long names for the other 2 A80 boards though.
Regards
ChenYu
>
> Thanks,
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
More information about the linux-arm-kernel
mailing list