[PATCH v6 5/5] ARM: dts: sun9i: Initial support for the Sunchip CX-A99 board
Maxime Ripard
maxime.ripard at free-electrons.com
Fri Feb 10 00:59:20 PST 2017
Hi,
On Thu, Feb 09, 2017 at 12:34:06AM +0100, Rask Ingemann Lambertsen wrote:
> The Suncip CX-A99 board is found in at least four brands of media players.
> It features an Allwinner A80 ARM SoC and is found in two models:
>
> 1) 2 GiB DDR3 DRAM and 16 GB eMMC
> 2) 4 GiB DDR3 DRAM and 32 GB eMMC
>
> For details of the board, see the linux-sunxi page
> <URL:https://linux-sunxi.org/Sunchip_CX-A99>.
Please don't put URLs in commit logs (and the DT).
>
> Supported features (+ means tested):
> + One Cortex-A7 CPU core (or four with experimental U-Boot PSCI patches)
> + AXP808 power management chip
> + OZ80120 voltage regulator
> + Serial console port (internal)
> + eMMC and SD card slot
> + USB 2.0 host ports on on-board USB hub
> + SATA port on on-board SATA-to-USB bridge *
> + IEEE 802.11 a/b/g/n/ac SDIO Wifi
> + Real-time clock
> + LEDs
> - IR receiver for remote control
>
> * Only shows up when a SATA device is connected. Also, if a power source
> is connected to the USB 3.0 connector across power cycles (e.g. FEL
> boot), the bridge may not properly reset and not show up on the USB bus.
> The vendor U-Boot performs some unknown magic which resets the bridge.
Is that magic at the USB level, or specific to the bridge itself?
> So far unsupported features:
> - Using any of the Cortex-A15 CPU cores
> - USB 3.0 port (except for supplying 5 V power)
> - IEEE 802.3 10/100/1000 megabit Ethernet
> - HDMI connector
> - S/PDIF audio output
> - Jack socket with composite video and analog stereo audio
> - Bluetooth
> - FM radio receiver (assuming it is even wired on the board)
I guess that should be in your cover letter.
This is not found in your DT, so no one really expects it to work :)
> Signed-off-by: Rask Ingemann Lambertsen <rask at formelder.dk>
> ---
>
> Changes in v6:
> - Updated commit message description of SATA-to-USB bridge quirk and added
> note about experimental U-Boot PSCI support for up to four CPU cores.
> - The blue LED is no longer on by default as its meaning is not documented.
> - Removed "regulator-boot-on" from regulators having "regulator-always-on".
> - Removed misleading mention of "OTG connector" which the device doesn't have.
> - More detailed explanation for the need for "broken-cd" on mmc0.
> - Several regulators have had their voltage range relaxed a little to match
> the permissible range according to the data sheets of the consumers. This
> is similar to what is used for the Cubieboard4 and Merrii A80 Optimus.
> - Shortened regulator dcdce name as per v5 comments. A comment now lists the
> pin groups supplied by dcdce.
>
> Changes in v5:
> - Switched pinmux modes to generic properties and dropped
> #include <dt-bindings/pinctrl/sun4i-a10.h> as a consequence.
> - Dropped pinctrl properties from GPIO nodes and dropped the pinmux
> nodes for them.
> - AXP808 regulators added.
> - Dropped the now unused #include <sunxi-common-regulators.dtsi>.
> - Ampak AP6335 SDIO-Wifi added.
> - USB Vbus changes as per v4 comments.
> - Added "broken-cd" to mmc0 because GPIO interrupts don't work.
>
> Changes in v4:
> - Node names had underscores changed to hyphens.
> - Changed formatting of the ac100/rtc node's clock output name list to match
> that of the same node in the cubieboard4 and a80-optimus device trees.
>
> Changes in v3:
> None.
>
> Changes in v2:
> - Fixed formatting and style issues found by scripts/checkpatch.pl.
>
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/sun9i-a80-cx-a99.dts | 409 +++++++++++++++++++++++++++++++++
> 2 files changed, 411 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/sun9i-a80-cx-a99.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 8553bd7..40546fa 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -862,7 +862,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \
> sun8i-v3s-licheepi-zero.dtb
> dtb-$(CONFIG_MACH_SUN9I) += \
> sun9i-a80-optimus.dtb \
> - sun9i-a80-cubieboard4.dtb
> + sun9i-a80-cubieboard4.dtb \
> + sun9i-a80-cx-a99.dtb
> dtb-$(CONFIG_ARCH_TANGO) += \
> tango4-vantage-1172.dtb
> dtb-$(CONFIG_ARCH_TEGRA_2x_SOC) += \
> diff --git a/arch/arm/boot/dts/sun9i-a80-cx-a99.dts b/arch/arm/boot/dts/sun9i-a80-cx-a99.dts
> new file mode 100644
> index 0000000..f5496d2
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun9i-a80-cx-a99.dts
> @@ -0,0 +1,409 @@
> +/*
> + * sun9i-a80-cx-a99.dts - Device Tree file for the Sunchip CX-A99 board.
> + *
> + * Copyright (C) 2017 Rask Ingemann Lambertsen <rask at formelder.dk>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/*
> + * The Sunchip CX-A99 board is found in several similar Android media
> + * players, such as:
> + *
> + * Instabox Fantasy A8 (no external antenna)
> + * Jesurun CS-Q8 (ships with larger remote control)
> + * Jesurun Maxone
> + * Rikomagic (RKM) MK80/MK80LE
> + * Tronsmart Draco AW80 Meta/Telos
> + *
> + * See <URL:https://linux-sunxi.org/Sunchip_CX-A99> for more information.
> + */
> +
> +/dts-v1/;
> +#include "sun9i-a80.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + model = "Sunchip CX-A99";
> + compatible = "sunchip,cx-a99", "allwinner,sun9i-a80";
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + blue {
> + gpios = <&pio 6 10 GPIO_ACTIVE_HIGH>; /* PG10 */
> + label = "cx-a99:blue:status";
> + };
> +
> + red {
> + gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
> + label = "cx-a99:red:status";
> + };
> + };
> +
> + powerseq_wifi: powerseq-wifi {
> + compatible = "mmc-pwrseq-simple";
> + clocks = <&ac100_rtc 1>;
> + clock-names = "ext_clock";
> + reset-gpios = <&r_pio 1 0 GPIO_ACTIVE_LOW>; /* PM0 */
> + post-power-on-delay-ms = <1>; /* Minimum 2 cycles. */
> + };
> +
> + /* USB 3.0 standard-A receptacle. For now, only Vbus is supported. */
I'm not sure what you mean by "only VBUS is supported"? Is there any
other signal?
> + reg_usb0_vbus: regulator-usb0-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb0-vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
> + enable-active-high;
This is redundant with the GPIO flag
> + regulator-always-on;
And it shouldn't be always on. The USB driver will enable it if needs
be.
> + };
> +
> + /*
> + * A GL850G hub with two external USB connectors is connected
> + * to ehci0. Each has a Vbus regulator controlled by a GPIO:
> + * PL7 for port 1, closest to the 12 V power connector, and
> + * PL8 for port 2, next to the SD card slot.
> + * Because regulator-fixed doesn't support a GPIO list, and
> + * allwinner,sun9i-a80-usb-phy doesn't support more than one
> + * supply, we have to use regulator-always-on on usb1-2-vbus.
> + * Note that the GPIO pins also need cldo1 to be enabled.
> + */
What is the source of those regulators connected then? Some PMIC
regulator? AC-IN?
> + reg_usb1_1_vbus: regulator-usb1-1-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb1-1-vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */
> + enable-active-high;
> + };
> +
> + reg_usb1_2_vbus: regulator-usb1-2-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb1-2-vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
> + enable-active-high;
> + regulator-always-on;
Same comment about always on. If the driver needs fixing to grab an
additional regulator, fix it, but this shouldn't be left that way.
> + };
> +
> + /* OZ80120 voltage regulator for the four Cortex-A15 cores. */
> + reg_vdd_cpub: regulator-vdd-cpub {
> + compatible = "regulator-gpio";
> +
> + regulator-always-on;
> + regulator-min-microvolt = < 800000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-name = "vdd-cpub";
> +
> + enable-gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
> + enable-active-high;
> + gpios = <&r_pio 0 3 GPIO_ACTIVE_HIGH>, /* PL3 */
> + <&r_pio 0 4 GPIO_ACTIVE_HIGH>, /* PL4 */
> + <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */
> +
> + gpios-states = <1 0 0>;
> + states = < 750000 0x7
> + 800000 0x3
> + 850000 0x5
> + 900000 0x1
> + 950000 0x6
> + 1000000 0x2
> + 1100000 0x4
> + 1200000 0x0>;
You're listing a minimum state of 750mv, yet your minimum voltage is
800mV.
> + };
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&ehci2 {
> + status = "okay";
> +};
> +
> +/*
> + * SD card slot. Although the GPIO pin for card detection is listed as capable
> + * of generating interrupts in the "A80 User Manual", this doesn't work for
> + * some unknown reason, so poll the GPIO for card detection. This is also what
> + * the vendor sys_config.fex file specifies.
> + */
> +&mmc0 {
> + bus-width = <4>;
> + cd-gpios = <&pio 7 17 GPIO_ACTIVE_LOW>; /* PH17 */
> + broken-cd; /* Poll. */
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins>;
> + vmmc-supply = <®_dcdce>;
> + status = "okay";
> +};
> +
> +/* Ampak AP6335 IEEE 802.11 a/b/g/n/ac "Wifi". */
Why "wifi" ? It's not implementing true wifi?
> +&mmc1 {
> + bus-width = <4>;
> + non-removable;
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc1_pins>;
> + vmmc-supply = <®_cldo3>; /* See cldo2,cldo3 note. */
> + vqmmc-supply = <®_aldo2>;
So it's able to support 1.2 or 1.8V IO modes? Surely you want to
enable those modes here to.
> + mmc-pwrseq = <&powerseq_wifi>;
> + status = "okay";
> +};
> +
> +/* On-board eMMC card. */
> +&mmc2 {
> + bus-width = <8>;
> + non-removable;
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc2_8bit_pins>;
> + vmmc-supply = <®_dcdce>;
> + status = "okay";
> +};
> +
> +&osc32k {
> + clocks = <&ac100_rtc 0>;
> +};
> +
> +&r_ir {
> + status = "okay";
> +};
> +
> +&r_rsb {
> + status = "okay";
> +
> + ac100: codec at e89 {
> + compatible = "x-powers,ac100";
> + reg = <0xe89>;
> +
> + ac100_codec: codec {
> + compatible = "x-powers,ac100-codec";
> + interrupt-parent = <&r_pio>;
> + interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>; /* PL9 */
> + #clock-cells = <0>;
> + clock-output-names = "4M_adda";
> + };
> +
> + ac100_rtc: rtc {
> + compatible = "x-powers,ac100-rtc";
> + interrupt-parent = <&nmi_intc>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&ac100_codec>;
> + #clock-cells = <1>;
> + clock-output-names = "cko1_rtc",
> + "cko2_rtc",
> + "cko3_rtc";
> + };
> + };
> +
> + pmic at 745 {
> + compatible = "x-powers,axp808", "x-powers,axp806";
> + reg = <0x745>;
> + interrupt-parent = <&nmi_intc>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> +
> + swin-supply = <®_dcdce>;
Please use an incude for that PMIC.
> +
> + /* In comments: Initial setup from vendor sys_config.fex. */
> + regulators {
> + /* 3.0 V (enabled). */
This might be disabled though.
> + reg_aldo1: aldo1 {
> + regulator-boot-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-name = "vcc-3v0";
> + };
> +
> + /* 1.8 V (enabled). */
> + reg_aldo2: aldo2 {
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3600000>;
> + regulator-name = "vcc-pg-pm-wifi+btio-audio";
Usually, there is simpler names available on the schematics, or at
least simpler names we can come up with.
Something like vcc-wifi would be enough her.
> + };
> +
> + /* 2.5 V (enabled). */
> + reg_aldo3: aldo3 {
> + regulator-boot-on;
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + regulator-name = "vcc-pa-gmac2v5";
vcc-gmac
> + };
> +
> + /* 1.8 V (enabled). */
> + reg_bldo1: bldo1 {
> + regulator-always-on; /* Hang if disabled */
> + regulator-min-microvolt = <1700000>;
> + regulator-max-microvolt = <1900000>;
> + regulator-name = "vdd18-dll-vcc18-pll";
vdd-dll
> + };
> +
> + /* 0.9 V (enabled). */
> + reg_bldo2: bldo2 {
> + regulator-always-on; /* Hang if disabled */
> + regulator-min-microvolt = < 800000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-name = "vdd-cpus";
> + };
> +
> + /* 1.2 V (disabled). */
> + reg_bldo3: bldo3 {
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-name = "vcc12-hsic";
vcc-hsic
> + };
> +
> + /* 1.1 V (enabled). */
> + reg_bldo4: bldo4 {
> + regulator-boot-on;
> + regulator-min-microvolt = < 800000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-name = "vdd09-hdmi";
vdd-hdmi
> + };
> +
> + /* 3.3 V (enabled). PLx pins control some regulators. */
> + reg_cldo1: cldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-pl-led";
vcc-led, etc...
Thanks,
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170210/ec920ad5/attachment-0001.sig>
More information about the linux-arm-kernel
mailing list