[PATCH v4 0/9] ARM: dts: support I2SE Duckbill devices

Michael Heimpold michael.heimpold at i2se.com
Wed Feb 8 23:42:40 PST 2017


This series updates/adds Device Tree support for I2SE's Duckbill
device family.

The Duckbill devices are small, pen-drive sized boards based on
NXP's i.MX28 SoC. While the initial variants (Duckbill series) were
equipped with a micro SD card slot only, the latest generation
(Duckbill 2 series) have an additional internal eMMC onboard.

Both device generations consists of four "family members":

- Duckbill/Duckbill 2: generic board, intended to be used as
  baseboard for custom designs and/or as development board

- Duckbill EnOcean/Duckbill 2 EnOcean: come with an EnOcean
  daugther board equipped with the popular TCM310 module

- Duckbill 485/Duckbill 2 485: as the name implies, these
  devices are intended to be used as Ethernet - RS485 converters

- Duckbill SPI/Duckbill 2 SPI: not sold separately, but used
  in I2SE's development kits for Green PHY HomePlug Powerline
  communication

Because the Duckbill series is EOL, this patch series only adds
support for the latest Duckbill 2 series devices. However,
support for the generic Duckbill board was already mainline,
so update it to match vendor tree DT.

Changes since v3:
- re-work compatible strings for individual products
- fixed subject prefix for documentation patch

Changes since v2:
- re-ordered documentation patch and fixed typos
- re-worded some commit messages to better reflect patch content
- fixed Makefile beginner issues
- added Acked-bys where applicable

Changes since v1:
- dropped device tree include (shared common definitions)
- added patch 9 (DT documentation file)
- applied reviewers hints
- rebased

Michael Heimpold (9):
  ARM: dts: imx28: add alternative pinmuxing for mmc2
  ARM: dts: imx28: rename mmc2_sck_cfg
  ARM: dts: imx28: add alternative muxing for mmc2_sck_cfg
  ARM: dts: imx28-duckbill: update to match vendor distributed DT
  dt-bindings: arm: add entries for I2SE boards
  ARM: dts: add support for I2SE Duckbill 2 boards
  ARM: dts: add support for I2SE Duckbill 2 485
  ARM: dts: add support for I2SE Duckbill 2 EnOcean
  ARM: dts: add support for I2SE Duckbill 2 SPI

 Documentation/devicetree/bindings/arm/i2se.txt |  22 +++
 arch/arm/boot/dts/Makefile                     |   4 +
 arch/arm/boot/dts/imx28-duckbill-2-485.dts     | 189 +++++++++++++++++++++
 arch/arm/boot/dts/imx28-duckbill-2-enocean.dts | 220 +++++++++++++++++++++++++
 arch/arm/boot/dts/imx28-duckbill-2-spi.dts     | 199 ++++++++++++++++++++++
 arch/arm/boot/dts/imx28-duckbill-2.dts         | 183 ++++++++++++++++++++
 arch/arm/boot/dts/imx28-duckbill.dts           |  81 ++++++---
 arch/arm/boot/dts/imx28-m28cu3.dts             |   2 +-
 arch/arm/boot/dts/imx28.dtsi                   |  28 +++-
 arch/arm/mach-mxs/mach-mxs.c                   |   3 +-
 10 files changed, 903 insertions(+), 28 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/arm/i2se.txt
 create mode 100644 arch/arm/boot/dts/imx28-duckbill-2-485.dts
 create mode 100644 arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
 create mode 100644 arch/arm/boot/dts/imx28-duckbill-2-spi.dts
 create mode 100644 arch/arm/boot/dts/imx28-duckbill-2.dts

-- 
2.6.1




More information about the linux-arm-kernel mailing list