[PATCH 1/7] Documentation: dt: iio: improve atmel-adc documentation

[Alexandre Belloni]

This corrects the example by removing the unit-address, as suggested by Mark
Rutland in
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-February/234184.html

Also, it removes the properties that are not used anymore, to stop propagating
them.

Finally, fixes a few typos.

Signed-off-by: Alexandre Belloni <alexandre.belloni at free-electrons.com>
---
 .../devicetree/bindings/arm/atmel-adc.txt          | 29 +++++++++-------------
 1 file changed, 12 insertions(+), 17 deletions(-)

diff --git a/Documentation/devicetree/bindings/arm/atmel-adc.txt b/Documentation/devicetree/bindings/arm/atmel-adc.txt
index d1061469f63d..ba3abfad656b 100644
--- a/Documentation/devicetree/bindings/arm/atmel-adc.txt
+++ b/Documentation/devicetree/bindings/arm/atmel-adc.txt
@@ -5,31 +5,31 @@ Required properties:
     <chip> can be "at91sam9260", "at91sam9g45" or "at91sam9x5"
   - reg: Should contain ADC registers location and length
   - interrupts: Should contain the IRQ line for the ADC
-  - atmel,adc-channels-used: Bitmask of the channels muxed and enable for this
+  - atmel,adc-channels-used: Bitmask of the channels muxed and enabled for this
     device
   - atmel,adc-startup-time: Startup Time of the ADC in microseconds as
     defined in the datasheet
   - atmel,adc-vref: Reference voltage in millivolts for the conversions
-  - atmel,adc-res: List of resolution in bits supported by the ADC. List size
+  - atmel,adc-res: List of resolutions in bits supported by the ADC. List size
 		   must be two at least.
   - atmel,adc-res-names: Contains one identifier string for each resolution
 			 in atmel,adc-res property. "lowres" and "highres"
 			 identifiers are required.
 
 Optional properties:
-  - atmel,adc-use-external: Boolean to enable of external triggers
+  - atmel,adc-use-external: Boolean to enable the external triggers
   - atmel,adc-use-res: String corresponding to an identifier from
 		       atmel,adc-res-names property. If not specified, the highest
 		       resolution will be used.
   - atmel,adc-sleep-mode: Boolean to enable sleep mode when no conversion
   - atmel,adc-sample-hold-time: Sample and Hold Time in microseconds
-  - atmel,adc-ts-wires: Number of touch screen wires. Should be 4 or 5. If this
-                        value is set, then adc driver will enable touch screen
+  - atmel,adc-ts-wires: Number of touchscreen wires. Should be 4 or 5. If this
+                        value is set, then the adc driver will enable touchscreen
                         support.
-    NOTE: when adc touch screen enabled, the adc hardware trigger will be
-          disabled. Since touch screen will occupied the trigger register.
+    NOTE: when adc touchscreen is enabled, the adc hardware trigger will be
+          disabled. Since touchscreen will occupy the trigger register.
   - atmel,adc-ts-pressure-threshold: a pressure threshold for touchscreen. It
-                                     make touch detect more precision.
+                                     makes touch detection more precise.
  
 Optional trigger Nodes:
   - Required properties:
@@ -44,37 +44,32 @@ adc0: adc at fffb0000 {
 	compatible = "atmel,at91sam9260-adc";
 	reg = <0xfffb0000 0x100>;
 	interrupts = <20 4>;
-	atmel,adc-channel-base = <0x30>;
 	atmel,adc-channels-used = <0xff>;
-	atmel,adc-drdy-mask = <0x10000>;
-	atmel,adc-num-channels = <8>;
 	atmel,adc-startup-time = <40>;
-	atmel,adc-status-register = <0x1c>;
-	atmel,adc-trigger-register = <0x08>;
 	atmel,adc-use-external;
 	atmel,adc-vref = <3300>;
 	atmel,adc-res = <8 10>;
 	atmel,adc-res-names = "lowres", "highres";
 	atmel,adc-use-res = "lowres";
 
-	trigger at 0 {
+	trigger0 {
 		trigger-name = "external-rising";
 		trigger-value = <0x1>;
 		trigger-external;
 	};
-	trigger at 1 {
+	trigger1 {
 		trigger-name = "external-falling";
 		trigger-value = <0x2>;
 		trigger-external;
 	};
 
-	trigger at 2 {
+	trigger2 {
 		trigger-name = "external-any";
 		trigger-value = <0x3>;
 		trigger-external;
 	};
 
-	trigger at 3 {
+	trigger3 {
 		trigger-name = "continuous";
 		trigger-value = <0x6>;
 	};
-- 
1.8.3.2