[PATCHv2 1/8] ARM: at91: Add at91sam9rl DT SoC support

[Mark Rutland]

On Wed, Feb 19, 2014 at 03:32:24PM +0000, Alexandre Belloni wrote:
> This adds preliminary DT support for the at91sam9rl.
> 
> Signed-off-by: Alexandre Belloni <alexandre.belloni at free-electrons.com>
> ---
>  arch/arm/boot/dts/at91sam9rl.dtsi | 628 ++++++++++++++++++++++++++++++++++++++
>  arch/arm/mach-at91/at91sam9rl.c   |  16 +
>  2 files changed, 644 insertions(+)
>  create mode 100644 arch/arm/boot/dts/at91sam9rl.dtsi
 
[...]

> +                       tcb0: timer at fffa0000 {
> +                               compatible = "atmel,at91rm9200-tcb";
> +                               reg = <0xfffa0000 0x100>;
> +                               interrupts = <16 IRQ_TYPE_LEVEL_HIGH 0
> +                                             17 IRQ_TYPE_LEVEL_HIGH 0
> +                                             18 IRQ_TYPE_LEVEL_HIGH 0>;
> +                       };

Nit: please bracket list entries individually. Also for other list
properties like reg and (*-)gpio(s).

[...]

> +                       adc0: adc at fffd0000 {
> +                               compatible = "atmel,at91sam9260-adc";
> +                               reg = <0xfffd0000 0x100>;
> +                               interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
> +                               atmel,adc-use-external-triggers;
> +                               atmel,adc-channels-used = <0xf>;
> +                               atmel,adc-vref = <3300>;
> +                               atmel,adc-num-channels = <4>;
> +                               atmel,adc-startup-time = <15>;
> +                               atmel,adc-channel-base = <0x30>;
> +                               atmel,adc-drdy-mask = <0x10000>;
> +                               atmel,adc-status-register = <0x1c>;
> +                               atmel,adc-trigger-register = <0x04>;
> +                               atmel,adc-res = <8 10>;
> +                               atmel,adc-res-names = "lowres", "highres";
> +                               atmel,adc-use-res = "highres";
> +
> +                               trigger at 0 {
> +                                       trigger-name = "timer-counter-0";
> +                                       trigger-value = <0x1>;
> +                               };

A unit-address should go with a reg value. Either this needs a reg and
the parent node needs #address-cells and #size-cells, or the
unit-address should go, and the names made unique through other means.

[...]

> +                       pinctrl at fffff400 {
> +                               #address-cells = <1>;
> +                               #size-cells = <1>;
> +                               compatible = "atmel,at91rm9200-pinctrl", "simple-bus";

NAK. Either this is a atmel,at91rm9200-pinctrl node or a simple-bus. Not
both; that doesn't make any sense.

> diff --git a/arch/arm/mach-at91/at91sam9rl.c b/arch/arm/mach-at91/at91sam9rl.c
> index 3651517abedf..d6ee8bb47213 100644
> --- a/arch/arm/mach-at91/at91sam9rl.c
> +++ b/arch/arm/mach-at91/at91sam9rl.c
> @@ -196,6 +196,22 @@ static struct clk_lookup periph_clocks_lookups[] = {
>         CLKDEV_CON_ID("pioB", &pioB_clk),
>         CLKDEV_CON_ID("pioC", &pioC_clk),
>         CLKDEV_CON_ID("pioD", &pioD_clk),
> +       /* more lookup table for DT entries */
> +       CLKDEV_CON_DEV_ID("usart", "fffff200.serial", &mck),
> +       CLKDEV_CON_DEV_ID("usart", "fffb0000.serial", &usart0_clk),
> +       CLKDEV_CON_DEV_ID("usart", "ffffb400.serial", &usart1_clk),
> +       CLKDEV_CON_DEV_ID("usart", "ffffb800.serial", &usart2_clk),
> +       CLKDEV_CON_DEV_ID("usart", "ffffbc00.serial", &usart3_clk),
> +       CLKDEV_CON_DEV_ID("t0_clk", "fffa0000.timer", &tc0_clk),
> +       CLKDEV_CON_DEV_ID("t1_clk", "fffa0000.timer", &tc1_clk),
> +       CLKDEV_CON_DEV_ID("t2_clk", "fffa0000.timer", &tc2_clk),
> +       CLKDEV_CON_DEV_ID("mci_clk", "fffa4000.mmc", &mmc_clk),
> +       CLKDEV_CON_DEV_ID(NULL, "fffa8000.i2c", &twi0_clk),
> +       CLKDEV_CON_DEV_ID(NULL, "fffac000.i2c", &twi1_clk),
> +       CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioA_clk),
> +       CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioB_clk),
> +       CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioC_clk),
> +       CLKDEV_CON_DEV_ID(NULL, "fffffa00.gpio", &pioD_clk),

Why can't these clocks be described in the DT?

Cheers,
Mark.