[PATCH 22/26] ARM: shmobile: mackerel: Use pinconf API to configure pin pull-down

[Simon Horman]

From: Laurent Pinchart <laurent.pinchart+renesas at ideasonboard.com>

The USB0 and USB1 VBUS pins must be pulled down. Add corresponding
configuration entries in the pinctrl map table instead of manually
poking the pin control registers.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas at ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas at verge.net.au>
---
 arch/arm/mach-shmobile/board-mackerel.c | 17 +++++++++--------
 arch/arm/mach-shmobile/sh-gpio.h        | 19 -------------------
 2 files changed, 9 insertions(+), 27 deletions(-)

diff --git a/arch/arm/mach-shmobile/board-mackerel.c b/arch/arm/mach-shmobile/board-mackerel.c
index d90d2f1..207acf0 100644
--- a/arch/arm/mach-shmobile/board-mackerel.c
+++ b/arch/arm/mach-shmobile/board-mackerel.c
@@ -41,6 +41,7 @@
 #include <linux/mtd/physmap.h>
 #include <linux/mtd/sh_flctl.h>
 #include <linux/pinctrl/machine.h>
+#include <linux/pinctrl/pinconf-generic.h>
 #include <linux/platform_data/gpio_backlight.h>
 #include <linux/pm_clock.h>
 #include <linux/regulator/fixed.h>
@@ -1311,6 +1312,10 @@ static struct i2c_board_info i2c1_devices[] = {
 	},
 };
 
+static unsigned long pin_pulldown_conf[] = {
+	PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 0),
+};
+
 static const struct pinctrl_map mackerel_pinctrl_map[] = {
 	/* ADXL34X */
 	PIN_MAP_MUX_GROUP_DEFAULT("1-0053", "pfc-sh7372",
@@ -1396,17 +1401,19 @@ static const struct pinctrl_map mackerel_pinctrl_map[] = {
 	/* USBHS0 */
 	PIN_MAP_MUX_GROUP_DEFAULT("renesas_usbhs.0", "pfc-sh7372",
 				  "usb0_vbus", "usb0"),
+	PIN_MAP_CONFIGS_GROUP_DEFAULT("renesas_usbhs.0", "pfc-sh7372",
+				      "usb0_vbus", pin_pulldown_conf),
 	/* USBHS1 */
 	PIN_MAP_MUX_GROUP_DEFAULT("renesas_usbhs.1", "pfc-sh7372",
 				  "usb1_vbus", "usb1"),
+	PIN_MAP_CONFIGS_GROUP_DEFAULT("renesas_usbhs.&", "pfc-sh7372",
+				      "usb1_vbus", pin_pulldown_conf),
 	PIN_MAP_MUX_GROUP_DEFAULT("renesas_usbhs.1", "pfc-sh7372",
 				  "usb1_otg_id_0", "usb1"),
 };
 
 #define GPIO_PORT9CR	IOMEM(0xE6051009)
 #define GPIO_PORT10CR	IOMEM(0xE605100A)
-#define GPIO_PORT167CR	IOMEM(0xE60520A7)
-#define GPIO_PORT168CR	IOMEM(0xE60520A8)
 #define SRCR4		IOMEM(0xe61580bc)
 #define USCCR1		IOMEM(0xE6058144)
 static void __init mackerel_init(void)
@@ -1446,12 +1453,6 @@ static void __init mackerel_init(void)
 
 	gpio_request_one(151, GPIOF_OUT_INIT_HIGH, NULL); /* LCDDON */
 
-	/* USBHS0 */
-	gpio_request_pulldown(GPIO_PORT168CR); /* VBUS0_0 pull down */
-
-	/* USBHS1 */
-	gpio_request_pulldown(GPIO_PORT167CR); /* VBUS0_1 pull down */
-
 	/* FSI2 port A (ak4643) */
 	gpio_request_one(161, GPIOF_OUT_INIT_LOW, NULL); /* slave */
 
diff --git a/arch/arm/mach-shmobile/sh-gpio.h b/arch/arm/mach-shmobile/sh-gpio.h
index e834763..2c41414 100644
--- a/arch/arm/mach-shmobile/sh-gpio.h
+++ b/arch/arm/mach-shmobile/sh-gpio.h
@@ -26,23 +26,4 @@ static inline void __init gpio_direction_none(void __iomem * addr)
 	__raw_writeb(0x00, addr);
 }
 
-static inline void __init gpio_request_pullup(void __iomem * addr)
-{
-	u8 data = __raw_readb(addr);
-
-	data &= 0x0F;
-	data |= 0xC0;
-	__raw_writeb(data, addr);
-}
-
-static inline void __init gpio_request_pulldown(void __iomem * addr)
-{
-	u8 data = __raw_readb(addr);
-
-	data &= 0x0F;
-	data |= 0xA0;
-
-	__raw_writeb(data, addr);
-}
-
 #endif /* __ASM_ARCH_GPIO_H */
-- 
1.8.4