[PATCH] pinctrl: at91: add support for OUTPUT config

boris brezillon b.brezillon at overkiz.com
Wed Aug 28 03:35:08 EDT 2013


On 28/08/2013 09:31, Nicolas Ferre wrote:
> On 27/08/2013 16:51, Boris BREZILLON :
>> Add support for pin output control through the pinctrl config:
>>   - support enabling/disabling output on a given pin
>>   - support output level setting (high or low)
>>
>> Signed-off-by: Boris BREZILLON <b.brezillon at overkiz.com>
>> ---
>>   .../bindings/pinctrl/atmel,at91-pinctrl.txt        |    2 ++
>>   drivers/pinctrl/pinctrl-at91.c                     |   22 
>> ++++++++++++++++++++
>>   include/dt-bindings/pinctrl/at91.h                 |    2 ++
>>   3 files changed, 26 insertions(+)
>>
>> diff --git 
>> a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt 
>> b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
>> index cf7c7bc..5a22e0d 100644
>> --- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
>> +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
>> @@ -90,6 +90,8 @@ MULTIDRIVE    (1 << 1): indicate this pin need to 
>> be configured as multidrive.
>>   DEGLITCH    (1 << 2): indicate this pin need deglitch.
>>   PULL_DOWN    (1 << 3): indicate this pin need a pull down.
>>   DIS_SCHMIT    (1 << 4): indicate this pin need to disable schmit 
>> trigger.
>> +OUTPUT        (1 << 5): indicate this pin need to be configured as 
>> an output.
>> +OUTPUT_VAL    (0x1 << 6): output val (1 = high, 0 = low)
>>   DEBOUNCE    (1 << 16): indicate this pin need debounce.
>>   DEBOUNCE_VAL    (0x3fff << 17): debounce val.
>>
>> diff --git a/drivers/pinctrl/pinctrl-at91.c 
>> b/drivers/pinctrl/pinctrl-at91.c
>> index 19afb9a..1578a0d 100644
>> --- a/drivers/pinctrl/pinctrl-at91.c
>> +++ b/drivers/pinctrl/pinctrl-at91.c
>> @@ -61,6 +61,9 @@ static int gpio_banks;
>>   #define DEGLITCH    (1 << 2)
>>   #define PULL_DOWN    (1 << 3)
>>   #define DIS_SCHMIT    (1 << 4)
>> +#define OUTPUT        (1 << 5)
>> +#define OUTPUT_VAL_SHIFT    6
>> +#define OUTPUT_VAL    (0x1 << OUTPUT_VAL_SHIFT)
>>   #define DEBOUNCE    (1 << 16)
>>   #define DEBOUNCE_VAL_SHIFT    17
>>   #define DEBOUNCE_VAL    (0x3fff << DEBOUNCE_VAL_SHIFT)
>> @@ -333,6 +336,19 @@ static void at91_mux_set_pullup(void __iomem 
>> *pio, unsigned mask, bool on)
>>       writel_relaxed(mask, pio + (on ? PIO_PUER : PIO_PUDR));
>>   }
>>
>> +static bool at91_mux_get_output(void __iomem *pio, unsigned pin, 
>> bool *val)
>> +{
>> +    *val = (readl_relaxed(pio + PIO_ODSR) >> pin) & 0x1;
>> +    return (readl_relaxed(pio + PIO_OSR) >> pin) & 0x1;
>> +}
>> +
>> +static void at91_mux_set_output(void __iomem *pio, unsigned mask, 
>> bool is_on,
>> +                bool val)
>> +{
>> +    writel_relaxed(mask, pio + (val ? PIO_SODR : PIO_CODR));
>> +    writel_relaxed(mask, pio + (is_on ? PIO_OER : PIO_ODR));
>> +}
>> +
>>   static unsigned at91_mux_get_multidrive(void __iomem *pio, unsigned 
>> pin)
>>   {
>>       return (readl_relaxed(pio + PIO_MDSR) >> pin) & 0x1;
>> @@ -712,6 +728,7 @@ static int at91_pinconf_get(struct pinctrl_dev 
>> *pctldev,
>>       void __iomem *pio;
>>       unsigned pin;
>>       int div;
>> +    bool out;
>>
>>       dev_dbg(info->dev, "%s:%d, pin_id=%d, config=0x%lx", __func__, 
>> __LINE__, pin_id, *config);
>>       pio = pin_to_controller(info, pin_to_bank(pin_id));
>> @@ -732,6 +749,9 @@ static int at91_pinconf_get(struct pinctrl_dev 
>> *pctldev,
>>       if (info->ops->get_schmitt_trig && 
>> info->ops->get_schmitt_trig(pio, pin))
>>           *config |= DIS_SCHMIT;
>>
>> +    if (at91_mux_get_output(pio, pin, &out))
>> +        *config |= OUTPUT | (out << OUTPUT_VAL_SHIFT);
>> +
>>       return 0;
>>   }
>>
>> @@ -749,6 +769,8 @@ static int at91_pinconf_set(struct pinctrl_dev 
>> *pctldev,
>>       if (config & PULL_UP && config & PULL_DOWN)
>>           return -EINVAL;
>>
>> +    at91_mux_set_output(pio, mask, config & OUTPUT,
>> +                (config & OUTPUT_VAL) >> OUTPUT_VAL_SHIFT);
>>       at91_mux_set_pullup(pio, mask, config & PULL_UP);
>>       at91_mux_set_multidrive(pio, mask, config & MULTI_DRIVE);
>>       if (info->ops->set_deglitch)
>> diff --git a/include/dt-bindings/pinctrl/at91.h 
>> b/include/dt-bindings/pinctrl/at91.h
>> index d7988b4..9fd4d48 100644
>> --- a/include/dt-bindings/pinctrl/at91.h
>> +++ b/include/dt-bindings/pinctrl/at91.h
>> @@ -15,6 +15,8 @@
>>   #define AT91_PINCTRL_DEGLITCH        (1 << 2)
>>   #define AT91_PINCTRL_PULL_DOWN        (1 << 3)
>>   #define AT91_PINCTRL_DIS_SCHMIT        (1 << 4)
>> +#define AT91_PINCTRL_OUTPUT        (1 << 5)
>> +#define AT91_PINCTRL_OUTPUT_VAL(x)    ((x & 0x1) << 6)
>
> Can you add this change to the documentation as well:
> Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
>
>
>>   #define AT91_PINCTRL_DEBOUNCE        (1 << 16)
>>   #define AT91_PINCTRL_DEBOUNCE_VA(x)    (x << 17)
>
> Oh, we have a nice typo here! ---^^^^^^
> And moreover it would be good to add the mask as well.

Do you want me to fix this typo and add mask for DEBOUNCE
in a separate patch ?

>
>>
>>
>
> Once the documentation added, you can stick my:
>
> Acked-by: Nicolas Ferre <nicolas.ferre at atmel.com>
>
> Thanks, bye,




More information about the linux-arm-kernel mailing list