[PATCH] pinctrl: at91: add support for OUTPUT config

[Nicolas Ferre]

On 27/08/2013 16:51, Boris BREZILLON :
> Add support for pin output control through the pinctrl config:
>   - support enabling/disabling output on a given pin
>   - support output level setting (high or low)
>
> Signed-off-by: Boris BREZILLON <b.brezillon at overkiz.com>
> ---
>   .../bindings/pinctrl/atmel,at91-pinctrl.txt        |    2 ++
>   drivers/pinctrl/pinctrl-at91.c                     |   22 ++++++++++++++++++++
>   include/dt-bindings/pinctrl/at91.h                 |    2 ++
>   3 files changed, 26 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
> index cf7c7bc..5a22e0d 100644
> --- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
> @@ -90,6 +90,8 @@ MULTIDRIVE	(1 << 1): indicate this pin need to be configured as multidrive.
>   DEGLITCH	(1 << 2): indicate this pin need deglitch.
>   PULL_DOWN	(1 << 3): indicate this pin need a pull down.
>   DIS_SCHMIT	(1 << 4): indicate this pin need to disable schmit trigger.
> +OUTPUT		(1 << 5): indicate this pin need to be configured as an output.
> +OUTPUT_VAL	(0x1 << 6): output val (1 = high, 0 = low)
>   DEBOUNCE	(1 << 16): indicate this pin need debounce.
>   DEBOUNCE_VAL	(0x3fff << 17): debounce val.
>
> diff --git a/drivers/pinctrl/pinctrl-at91.c b/drivers/pinctrl/pinctrl-at91.c
> index 19afb9a..1578a0d 100644
> --- a/drivers/pinctrl/pinctrl-at91.c
> +++ b/drivers/pinctrl/pinctrl-at91.c
> @@ -61,6 +61,9 @@ static int gpio_banks;
>   #define DEGLITCH	(1 << 2)
>   #define PULL_DOWN	(1 << 3)
>   #define DIS_SCHMIT	(1 << 4)
> +#define OUTPUT		(1 << 5)
> +#define OUTPUT_VAL_SHIFT	6
> +#define OUTPUT_VAL	(0x1 << OUTPUT_VAL_SHIFT)
>   #define DEBOUNCE	(1 << 16)
>   #define DEBOUNCE_VAL_SHIFT	17
>   #define DEBOUNCE_VAL	(0x3fff << DEBOUNCE_VAL_SHIFT)
> @@ -333,6 +336,19 @@ static void at91_mux_set_pullup(void __iomem *pio, unsigned mask, bool on)
>   	writel_relaxed(mask, pio + (on ? PIO_PUER : PIO_PUDR));
>   }
>
> +static bool at91_mux_get_output(void __iomem *pio, unsigned pin, bool *val)
> +{
> +	*val = (readl_relaxed(pio + PIO_ODSR) >> pin) & 0x1;
> +	return (readl_relaxed(pio + PIO_OSR) >> pin) & 0x1;
> +}
> +
> +static void at91_mux_set_output(void __iomem *pio, unsigned mask, bool is_on,
> +				bool val)
> +{
> +	writel_relaxed(mask, pio + (val ? PIO_SODR : PIO_CODR));
> +	writel_relaxed(mask, pio + (is_on ? PIO_OER : PIO_ODR));
> +}
> +
>   static unsigned at91_mux_get_multidrive(void __iomem *pio, unsigned pin)
>   {
>   	return (readl_relaxed(pio + PIO_MDSR) >> pin) & 0x1;
> @@ -712,6 +728,7 @@ static int at91_pinconf_get(struct pinctrl_dev *pctldev,
>   	void __iomem *pio;
>   	unsigned pin;
>   	int div;
> +	bool out;
>
>   	dev_dbg(info->dev, "%s:%d, pin_id=%d, config=0x%lx", __func__, __LINE__, pin_id, *config);
>   	pio = pin_to_controller(info, pin_to_bank(pin_id));
> @@ -732,6 +749,9 @@ static int at91_pinconf_get(struct pinctrl_dev *pctldev,
>   	if (info->ops->get_schmitt_trig && info->ops->get_schmitt_trig(pio, pin))
>   		*config |= DIS_SCHMIT;
>
> +	if (at91_mux_get_output(pio, pin, &out))
> +		*config |= OUTPUT | (out << OUTPUT_VAL_SHIFT);
> +
>   	return 0;
>   }
>
> @@ -749,6 +769,8 @@ static int at91_pinconf_set(struct pinctrl_dev *pctldev,
>   	if (config & PULL_UP && config & PULL_DOWN)
>   		return -EINVAL;
>
> +	at91_mux_set_output(pio, mask, config & OUTPUT,
> +			    (config & OUTPUT_VAL) >> OUTPUT_VAL_SHIFT);
>   	at91_mux_set_pullup(pio, mask, config & PULL_UP);
>   	at91_mux_set_multidrive(pio, mask, config & MULTI_DRIVE);
>   	if (info->ops->set_deglitch)
> diff --git a/include/dt-bindings/pinctrl/at91.h b/include/dt-bindings/pinctrl/at91.h
> index d7988b4..9fd4d48 100644
> --- a/include/dt-bindings/pinctrl/at91.h
> +++ b/include/dt-bindings/pinctrl/at91.h
> @@ -15,6 +15,8 @@
>   #define AT91_PINCTRL_DEGLITCH		(1 << 2)
>   #define AT91_PINCTRL_PULL_DOWN		(1 << 3)
>   #define AT91_PINCTRL_DIS_SCHMIT		(1 << 4)
> +#define AT91_PINCTRL_OUTPUT		(1 << 5)
> +#define AT91_PINCTRL_OUTPUT_VAL(x)	((x & 0x1) << 6)

Can you add this change to the documentation as well:
Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt


>   #define AT91_PINCTRL_DEBOUNCE		(1 << 16)
>   #define AT91_PINCTRL_DEBOUNCE_VA(x)	(x << 17)

Oh, we have a nice typo here! ---^^^^^^
And moreover it would be good to add the mask as well.

>
>

Once the documentation added, you can stick my:

Acked-by: Nicolas Ferre <nicolas.ferre at atmel.com>

Thanks, bye,
-- 
Nicolas Ferre