[PATCH 07/12] ARM: move all dtb targets out of Makefile.boot

[Jean-Christophe PLAGNIOL-VILLARD]

On 12:51 Mon 10 Sep     , Rob Herring wrote:
> On 09/10/2012 10:52 AM, Jean-Christophe PLAGNIOL-VILLARD wrote:
> > On 15:12 Thu 06 Sep     , Rob Herring wrote:
> >> From: Rob Herring <rob.herring at calxeda.com>
> >>
> >> In preparation to support multi-platform kernels, move all the dtb targets
> >> out of the mach Makefile.boot and into the arch/arm/boot/dts/Makefile
> >> which is closer to the sources.
> >>
> >> Signed-off-by: Rob Herring <rob.herring at calxeda.com>
> >> Cc: Russell King <linux at arm.linux.org.uk>
> >> Cc: Andrew Victor <linux at maxim.org.za>
> >> Cc: Nicolas Ferre <nicolas.ferre at atmel.com>
> >> Cc: Jean-Christophe Plagniol-Villard <plagnioj at jcrosoft.com>
> >> Cc: Kukjin Kim <kgene.kim at samsung.com>
> >> Cc: Sascha Hauer <kernel at pengutronix.de>
> >> Cc: Jason Cooper <jason at lakedaemon.net>
> >> Cc: Andrew Lunn <andrew at lunn.ch>
> >> Cc: Gregory Clement <gregory.clement at free-electrons.com>
> >> Cc: Shawn Guo <shawn.guo at linaro.org>
> >> Cc: Viresh Kumar <viresh.linux at gmail.com>
> >> Cc: Shiraz Hashim <shiraz.hashim at st.com>
> >> Cc: Rajeev Kumar <rajeev-dlh.kumar at st.com>
> >> Cc: Stephen Warren <swarren at wwwdotorg.org>
> >> Cc: Srinidhi Kasagar <srinidhi.kasagar at stericsson.com>
> >> Cc: Linus Walleij <linus.walleij at linaro.org>
> >> ---
> >>  arch/arm/boot/Makefile                |    2 ++
> >>  arch/arm/boot/dts/Makefile            |   41 +++++++++++++++++++++++++++++++++
> >>  arch/arm/mach-at91/Makefile.boot      |   24 -------------------
> >>  arch/arm/mach-exynos/Makefile.boot    |    3 ---
> >>  arch/arm/mach-imx/Makefile.boot       |    7 ------
> >>  arch/arm/mach-kirkwood/Makefile.boot  |   11 ---------
> >>  arch/arm/mach-lpc32xx/Makefile.boot   |    2 --
> >>  arch/arm/mach-mvebu/Makefile.boot     |    2 --
> >>  arch/arm/mach-mxs/Makefile.boot       |    9 --------
> >>  arch/arm/mach-spear13xx/Makefile.boot |    3 ---
> >>  arch/arm/mach-spear3xx/Makefile.boot  |    4 ----
> >>  arch/arm/mach-spear6xx/Makefile.boot  |    2 --
> >>  arch/arm/mach-tegra/Makefile.boot     |    8 -------
> >>  arch/arm/mach-ux500/Makefile.boot     |    2 --
> >>  arch/arm/mach-vexpress/Makefile.boot  |    5 ----
> >>  15 files changed, 43 insertions(+), 82 deletions(-)
> >>  create mode 100644 arch/arm/boot/dts/Makefile
> >>
> >> diff --git a/arch/arm/boot/Makefile b/arch/arm/boot/Makefile
> >> index c877087..3fdab01 100644
> >> --- a/arch/arm/boot/Makefile
> >> +++ b/arch/arm/boot/Makefile
> >> @@ -15,6 +15,8 @@ ifneq ($(MACHINE),)
> >>  include $(srctree)/$(MACHINE)/Makefile.boot
> >>  endif
> >>  
> >> +include $(srctree)/arch/arm/boot/dts/Makefile
> >> +
> >>  # Note: the following conditions must always be true:
> >>  #   ZRELADDR == virt_to_phys(PAGE_OFFSET + TEXT_OFFSET)
> >>  #   PARAMS_PHYS must be within 4MB of ZRELADDR
> >> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> >> new file mode 100644
> >> index 0000000..e59586b
> >> --- /dev/null
> >> +++ b/arch/arm/boot/dts/Makefile
> >> @@ -0,0 +1,41 @@
> >> +dtb-$(CONFIG_ARCH_HIGHBANK) += highbank.dtb
> > sorry I see no need of the dtb-y
> > 
> > just do all the time
> 
> That's not how it works today. dtb's only for all enabled platforms are
> built. Changing the behavior should be a different patch.
no I see no point to check if the platform is enable or not just build all

This will allow to check them

Best Regards,
J.