[PATCHv6 10/14] ARM: OMAP: TWL: change the vddmin / vddmax voltages to spec

[Tero Kristo]

As vddmin / vddmax voltages for the pmic only describe the pmic
capabilities now, change the voltages to be according to spec.
TWL data manuals give following values:

TWL4030 (SWCS019L) : VDD1: 600mV ... 1450mV, VDD2: 600mV ... 1500mV
TWL5030 (SWCS030E) : VDD1: 600mV ... 1450mV, VDD2: 600mV ... 1500mV
TWL6030 (SWCS045A) : 0V ... 2100mV

Signed-off-by: Tero Kristo <t-kristo at ti.com>
---
 arch/arm/mach-omap2/omap_twl.c |   27 ++++++++++-----------------
 1 files changed, 10 insertions(+), 17 deletions(-)

diff --git a/arch/arm/mach-omap2/omap_twl.c b/arch/arm/mach-omap2/omap_twl.c
index dca1d66..188f210 100644
--- a/arch/arm/mach-omap2/omap_twl.c
+++ b/arch/arm/mach-omap2/omap_twl.c
@@ -145,8 +145,8 @@ static struct omap_voltdm_pmic omap3_mpu_pmic = {
 	.vp_erroroffset		= OMAP3_VP_CONFIG_ERROROFFSET,
 	.vp_vstepmin		= OMAP3_VP_VSTEPMIN_VSTEPMIN,
 	.vp_vstepmax		= OMAP3_VP_VSTEPMAX_VSTEPMAX,
-	.vddmin			= OMAP3430_VP1_VLIMITTO_VDDMIN,
-	.vddmax			= OMAP3430_VP1_VLIMITTO_VDDMAX,
+	.vddmin			= 600000,
+	.vddmax			= 1450000,
 	.vp_timeout_us		= OMAP3_VP_VLIMITTO_TIMEOUT_US,
 	.i2c_slave_addr		= OMAP3_SRI2C_SLAVE_ADDR,
 	.volt_reg_addr		= OMAP3_VDD_MPU_SR_CONTROL_REG,
@@ -162,8 +162,8 @@ static struct omap_voltdm_pmic omap3_core_pmic = {
 	.vp_erroroffset		= OMAP3_VP_CONFIG_ERROROFFSET,
 	.vp_vstepmin		= OMAP3_VP_VSTEPMIN_VSTEPMIN,
 	.vp_vstepmax		= OMAP3_VP_VSTEPMAX_VSTEPMAX,
-	.vddmin			= OMAP3430_VP2_VLIMITTO_VDDMIN,
-	.vddmax			= OMAP3430_VP2_VLIMITTO_VDDMAX,
+	.vddmin			= 600000,
+	.vddmax			= 1450000,
 	.vp_timeout_us		= OMAP3_VP_VLIMITTO_TIMEOUT_US,
 	.i2c_slave_addr		= OMAP3_SRI2C_SLAVE_ADDR,
 	.volt_reg_addr		= OMAP3_VDD_CORE_SR_CONTROL_REG,
@@ -179,8 +179,8 @@ static struct omap_voltdm_pmic omap4_mpu_pmic = {
 	.vp_erroroffset		= OMAP4_VP_CONFIG_ERROROFFSET,
 	.vp_vstepmin		= OMAP4_VP_VSTEPMIN_VSTEPMIN,
 	.vp_vstepmax		= OMAP4_VP_VSTEPMAX_VSTEPMAX,
-	.vddmin			= OMAP4_VP_MPU_VLIMITTO_VDDMIN,
-	.vddmax			= OMAP4_VP_MPU_VLIMITTO_VDDMAX,
+	.vddmin			= 0,
+	.vddmax			= 2100000,
 	.vp_timeout_us		= OMAP4_VP_VLIMITTO_TIMEOUT_US,
 	.i2c_slave_addr		= OMAP4_SRI2C_SLAVE_ADDR,
 	.volt_reg_addr		= OMAP4_VDD_MPU_SR_VOLT_REG,
@@ -197,8 +197,8 @@ static struct omap_voltdm_pmic omap4_iva_pmic = {
 	.vp_erroroffset		= OMAP4_VP_CONFIG_ERROROFFSET,
 	.vp_vstepmin		= OMAP4_VP_VSTEPMIN_VSTEPMIN,
 	.vp_vstepmax		= OMAP4_VP_VSTEPMAX_VSTEPMAX,
-	.vddmin			= OMAP4_VP_IVA_VLIMITTO_VDDMIN,
-	.vddmax			= OMAP4_VP_IVA_VLIMITTO_VDDMAX,
+	.vddmin			= 0,
+	.vddmax			= 2100000,
 	.vp_timeout_us		= OMAP4_VP_VLIMITTO_TIMEOUT_US,
 	.i2c_slave_addr		= OMAP4_SRI2C_SLAVE_ADDR,
 	.volt_reg_addr		= OMAP4_VDD_IVA_SR_VOLT_REG,
@@ -215,8 +215,8 @@ static struct omap_voltdm_pmic omap4_core_pmic = {
 	.vp_erroroffset		= OMAP4_VP_CONFIG_ERROROFFSET,
 	.vp_vstepmin		= OMAP4_VP_VSTEPMIN_VSTEPMIN,
 	.vp_vstepmax		= OMAP4_VP_VSTEPMAX_VSTEPMAX,
-	.vddmin			= OMAP4_VP_CORE_VLIMITTO_VDDMIN,
-	.vddmax			= OMAP4_VP_CORE_VLIMITTO_VDDMAX,
+	.vddmin			= 0,
+	.vddmax			= 2100000,
 	.vp_timeout_us		= OMAP4_VP_VLIMITTO_TIMEOUT_US,
 	.i2c_slave_addr		= OMAP4_SRI2C_SLAVE_ADDR,
 	.volt_reg_addr		= OMAP4_VDD_CORE_SR_VOLT_REG,
@@ -251,13 +251,6 @@ int __init omap3_twl_init(void)
 	if (!cpu_is_omap34xx())
 		return -ENODEV;
 
-	if (cpu_is_omap3630()) {
-		omap3_mpu_pmic.vddmin = OMAP3630_VP1_VLIMITTO_VDDMIN;
-		omap3_mpu_pmic.vddmax = OMAP3630_VP1_VLIMITTO_VDDMAX;
-		omap3_core_pmic.vddmin = OMAP3630_VP2_VLIMITTO_VDDMIN;
-		omap3_core_pmic.vddmax = OMAP3630_VP2_VLIMITTO_VDDMAX;
-	}
-
 	/*
 	 * The smartreflex bit on twl4030 specifies if the setting of voltage
 	 * is done over the I2C_SR path. Since this setting is independent of
-- 
1.7.4.1