[PATCH 03/11] ARM: at91/soc: use gpio_is_valid to check the gpio

Jean-Christophe PLAGNIOL-VILLARD plagnioj at jcrosoft.com
Sun Oct 16 15:09:12 EDT 2011


Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre at atmel.com>
---
 arch/arm/mach-at91/at91cap9_devices.c    |   20 ++++++++++----------
 arch/arm/mach-at91/at91rm9200_devices.c  |   22 +++++++++++-----------
 arch/arm/mach-at91/at91sam9260_devices.c |   26 +++++++++++++-------------
 arch/arm/mach-at91/at91sam9261_devices.c |   14 +++++++-------
 arch/arm/mach-at91/at91sam9263_devices.c |   26 +++++++++++++-------------
 arch/arm/mach-at91/at91sam9g45_devices.c |   20 ++++++++++----------
 arch/arm/mach-at91/at91sam9rl_devices.c  |   16 ++++++++--------
 7 files changed, 72 insertions(+), 72 deletions(-)

diff --git a/arch/arm/mach-at91/at91cap9_devices.c b/arch/arm/mach-at91/at91cap9_devices.c
index b46615a..97db597 100644
--- a/arch/arm/mach-at91/at91cap9_devices.c
+++ b/arch/arm/mach-at91/at91cap9_devices.c
@@ -76,7 +76,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
 
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
-		if (data->vbus_pin[i])
+		if (gpio_is_valid(data->vbus_pin[i]))
 			at91_set_gpio_output(data->vbus_pin[i], 0);
 	}
 
@@ -179,7 +179,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data)
 	usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
 	memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));
 
-	if (data && data->vbus_pin > 0) {
+	if (data && gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 		usba_udc_data.pdata.vbus_pin = data->vbus_pin;
@@ -232,7 +232,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
 	if (!data)
 		return;
 
-	if (data->phy_irq_pin) {
+	if (gpio_is_valid(data->phy_irq_pin)) {
 		at91_set_gpio_input(data->phy_irq_pin, 0);
 		at91_set_deglitch(data->phy_irq_pin, 1);
 	}
@@ -332,13 +332,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	if (mmc_id == 0) {		/* MCI0 */
@@ -425,15 +425,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	nand_data = *data;
@@ -807,7 +807,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
 	at91_set_A_periph(AT91_PIN_PA9, 0);	/* AC97RX */
 
 	/* reset */
-	if (data->reset_pin)
+	if (gpio_is_valid(data->reset_pin))
 		at91_set_gpio_output(data->reset_pin, 0);
 
 	ac97_data = *data;
diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c
index 3f27113..fdae689 100644
--- a/arch/arm/mach-at91/at91rm9200_devices.c
+++ b/arch/arm/mach-at91/at91rm9200_devices.c
@@ -114,11 +114,11 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
 	if (!data)
 		return;
 
-	if (data->vbus_pin) {
+	if (gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 	}
-	if (data->pullup_pin)
+	if (gpio_is_valid(data->pullup_pin))
 		at91_set_gpio_output(data->pullup_pin, 0);
 
 	udc_data = *data;
@@ -167,7 +167,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
 	if (!data)
 		return;
 
-	if (data->phy_irq_pin) {
+	if (gpio_is_valid(data->phy_irq_pin)) {
 		at91_set_gpio_input(data->phy_irq_pin, 0);
 		at91_set_deglitch(data->phy_irq_pin, 1);
 	}
@@ -260,7 +260,7 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
 	);
 
 	/* input/irq */
-	if (data->irq_pin) {
+	if (gpio_is_valid(data->irq_pin)) {
 		at91_set_gpio_input(data->irq_pin, 1);
 		at91_set_deglitch(data->irq_pin, 1);
 	}
@@ -268,7 +268,7 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
 	at91_set_deglitch(data->det_pin, 1);
 
 	/* outputs, initially off */
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 	at91_set_gpio_output(data->rst_pin, 0);
 
@@ -328,13 +328,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	/* CLK */
@@ -419,15 +419,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	at91_set_A_periph(AT91_PIN_PC1, 0);		/* SMOE */
diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c
index 344075f..f00fed4 100644
--- a/arch/arm/mach-at91/at91sam9260_devices.c
+++ b/arch/arm/mach-at91/at91sam9260_devices.c
@@ -115,7 +115,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
 	if (!data)
 		return;
 
-	if (data->vbus_pin) {
+	if (gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 	}
@@ -168,7 +168,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
 	if (!data)
 		return;
 
-	if (data->phy_irq_pin) {
+	if (gpio_is_valid(data->phy_irq_pin)) {
 		at91_set_gpio_input(data->phy_irq_pin, 0);
 		at91_set_deglitch(data->phy_irq_pin, 1);
 	}
@@ -243,13 +243,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	/* CLK */
@@ -330,11 +330,11 @@ void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
 	for (i = 0; i < ATMEL_MCI_MAX_NR_SLOTS; i++) {
 		if (data->slot[i].bus_width) {
 			/* input/irq */
-			if (data->slot[i].detect_pin) {
+			if (gpio_is_valid(data->slot[i].detect_pin)) {
 				at91_set_gpio_input(data->slot[i].detect_pin, 1);
 				at91_set_deglitch(data->slot[i].detect_pin, 1);
 			}
-			if (data->slot[i].wp_pin)
+			if (gpio_is_valid(data->slot[i].wp_pin))
 				at91_set_gpio_input(data->slot[i].wp_pin, 1);
 
 			switch (i) {
@@ -426,15 +426,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	nand_data = *data;
@@ -1282,17 +1282,17 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
 
 	at91_sys_write(AT91_MATRIX_EBICSA, csa);
 
-	if (data->rst_pin) {
+	if (gpio_is_valid(data->rst_pin)) {
 		at91_set_multi_drive(data->rst_pin, 0);
 		at91_set_gpio_output(data->rst_pin, 1);
 	}
 
-	if (data->irq_pin) {
+	if (gpio_is_valid(data->irq_pin)) {
 		at91_set_gpio_input(data->irq_pin, 0);
 		at91_set_deglitch(data->irq_pin, 1);
 	}
 
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 0);
 		at91_set_deglitch(data->det_pin, 1);
 	}
diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
index 3b8fb79..773aae4 100644
--- a/arch/arm/mach-at91/at91sam9261_devices.c
+++ b/arch/arm/mach-at91/at91sam9261_devices.c
@@ -118,7 +118,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
 	if (!data)
 		return;
 
-	if (data->vbus_pin) {
+	if (gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 	}
@@ -171,13 +171,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	/* CLK */
@@ -240,15 +240,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	at91_set_A_periph(AT91_PIN_PC0, 0);		/* NANDOE */
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index d4aef76..a1b1354 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -70,7 +70,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
 
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
-		if (data->vbus_pin[i])
+		if (gpio_is_valid(data->vbus_pin[i]))
 			at91_set_gpio_output(data->vbus_pin[i], 0);
 	}
 
@@ -123,7 +123,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
 	if (!data)
 		return;
 
-	if (data->vbus_pin) {
+	if (gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 	}
@@ -176,7 +176,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
 	if (!data)
 		return;
 
-	if (data->phy_irq_pin) {
+	if (gpio_is_valid(data->phy_irq_pin)) {
 		at91_set_gpio_input(data->phy_irq_pin, 0);
 		at91_set_deglitch(data->phy_irq_pin, 1);
 	}
@@ -276,13 +276,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	if (mmc_id == 0) {		/* MCI0 */
@@ -430,17 +430,17 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
 	}
 	at91_sys_write(AT91_MATRIX_EBI0CSA, ebi0_csa);
 
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
 
-	if (data->irq_pin) {
+	if (gpio_is_valid(data->irq_pin)) {
 		at91_set_gpio_input(data->irq_pin, 1);
 		at91_set_deglitch(data->irq_pin, 1);
 	}
 
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		/* initially off */
 		at91_set_gpio_output(data->vcc_pin, 0);
 
@@ -500,15 +500,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBI0CSA, csa | AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	nand_data = *data;
@@ -749,7 +749,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
 	at91_set_A_periph(AT91_PIN_PB3, 0);	/* AC97RX */
 
 	/* reset */
-	if (data->reset_pin)
+	if (gpio_is_valid(data->reset_pin))
 		at91_set_gpio_output(data->reset_pin, 0);
 
 	ac97_data = *data;
diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
index e4a9857..ffd655b 100644
--- a/arch/arm/mach-at91/at91sam9g45_devices.c
+++ b/arch/arm/mach-at91/at91sam9g45_devices.c
@@ -120,7 +120,7 @@ void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data)
 
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
-		if (data->vbus_pin[i])
+		if (gpio_is_valid(data->vbus_pin[i]))
 			at91_set_gpio_output(data->vbus_pin[i], 0);
 	}
 
@@ -181,7 +181,7 @@ void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data)
 
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
-		if (data->vbus_pin[i])
+		if (gpio_is_valid(data->vbus_pin[i]))
 			at91_set_gpio_output(data->vbus_pin[i], 0);
 	}
 
@@ -263,7 +263,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data)
 	usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
 	memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));
 
-	if (data && data->vbus_pin > 0) {
+	if (data && gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 		usba_udc_data.pdata.vbus_pin = data->vbus_pin;
@@ -316,7 +316,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
 	if (!data)
 		return;
 
-	if (data->phy_irq_pin) {
+	if (gpio_is_valid(data->phy_irq_pin)) {
 		at91_set_gpio_input(data->phy_irq_pin, 0);
 		at91_set_deglitch(data->phy_irq_pin, 1);
 	}
@@ -449,11 +449,11 @@ void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
 
 
 	/* input/irq */
-	if (data->slot[0].detect_pin) {
+	if (gpio_is_valid(data->slot[0].detect_pin)) {
 		at91_set_gpio_input(data->slot[0].detect_pin, 1);
 		at91_set_deglitch(data->slot[0].detect_pin, 1);
 	}
-	if (data->slot[0].wp_pin)
+	if (gpio_is_valid(data->slot[0].wp_pin))
 		at91_set_gpio_input(data->slot[0].wp_pin, 1);
 
 	if (mmc_id == 0) {		/* MCI0 */
@@ -556,15 +556,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	nand_data = *data;
@@ -859,7 +859,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
 	at91_set_A_periph(AT91_PIN_PD6, 0);	/* AC97RX */
 
 	/* reset */
-	if (data->reset_pin)
+	if (gpio_is_valid(data->reset_pin))
 		at91_set_gpio_output(data->reset_pin, 0);
 
 	ac97_data = *data;
diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
index aacb19d..56cb73d 100644
--- a/arch/arm/mach-at91/at91sam9rl_devices.c
+++ b/arch/arm/mach-at91/at91sam9rl_devices.c
@@ -147,7 +147,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data)
 	usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
 	memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));
 
-	if (data && data->vbus_pin > 0) {
+	if (data && gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 		usba_udc_data.pdata.vbus_pin = data->vbus_pin;
@@ -201,13 +201,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	/* CLK */
@@ -275,15 +275,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	at91_set_A_periph(AT91_PIN_PB4, 0);		/* NANDOE */
@@ -483,7 +483,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
 	at91_set_A_periph(AT91_PIN_PD4, 0);	/* AC97RX */
 
 	/* reset */
-	if (data->reset_pin)
+	if (gpio_is_valid(data->reset_pin))
 		at91_set_gpio_output(data->reset_pin, 0);
 
 	ac97_data = *data;
-- 
1.7.7




More information about the linux-arm-kernel mailing list