[PATCH V7 4/4] mmc: sdhci-esdhc: enable esdhc on imx53

Richard Zhu Hong-Xing.Zhu at freescale.com
Fri Mar 18 05:56:57 EDT 2011


Fix the NO INT in the Multi-BLK IO in SD/MMC, and Multi-BLK
read in SDIO on imx53.

The CMDTYPE of the CMD register (offset 0xE) should be set to
"11" when the STOP CMD12 is issued on imx53 to abort one
open ended multi-blk IO. Otherwise one the TC INT wouldn't
be generated.

In exact block transfer, the controller doesn't complete the
operations automatically as required at the end of the
transfer and remains on hold if the abort command is not sent on
imx53.
As a result, the TC flag is not asserted and SW  received timeout
exeception. set bit1 of Vendor Spec registor to fix it.

Signed-off-by: Richard Zhu <Hong-Xing.Zhu at freescale.com>
Signed-off-by: Richard Zhao <richard.zhao at freescale.com>
---
 drivers/mmc/host/sdhci-esdhc-imx.c |   42 ++++++++++++++++++++++++++++++++++++
 1 files changed, 42 insertions(+), 0 deletions(-)

diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index a558d86..fac0204 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -19,13 +19,31 @@
 #include <linux/slab.h>
 #include <linux/mmc/host.h>
 #include <linux/mmc/sdhci-pltfm.h>
+#include <linux/mmc/mmc.h>
+#include <linux/mmc/sdio.h>
 #include <mach/hardware.h>
 #include <mach/esdhc.h>
 #include "sdhci.h"
 #include "sdhci-pltfm.h"
 #include "sdhci-esdhc.h"
 
+/* VENDOR SPEC register */
+#define SDHCI_VENDOR_SPEC		0xC0
+#define  SDHCI_VENDOR_SPEC_SDIO_QUIRK	0x00000002
+
 #define ESDHC_FLAG_GPIO_FOR_CD_WP	(1 << 0)
+/*
+ * The CMDTYPE of the CMD register (offset 0xE) should be set to
+ * "11" when the STOP CMD12 is issued on imx53 to abort one
+ * open ended multi-blk IO. Otherwise the TC INT wouldn't
+ * be generated.
+ * In exact block transfer, the controller doesn't complete the
+ * operations automatically as required at the end of the
+ * transfer and remains on hold if the abort command is not sent.
+ * As a result, the TC flag is not asserted and SW  received timeout
+ * exeception. Bit1 of Vendor Spec registor is used to fix it.
+ */
+#define ESDHC_FLAG_MULTIBLK_NO_INT	(1 << 1)
 
 struct pltfm_imx_data {
 	int flags;
@@ -80,6 +98,15 @@ static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg)
 		 */
 		val &= ~(SDHCI_INT_CARD_REMOVE | SDHCI_INT_CARD_INSERT);
 
+	if (unlikely((imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT)
+				&& (reg == SDHCI_INT_STATUS)
+				&& (val & SDHCI_INT_DATA_END))) {
+			u32 v;
+			v = readl(host->ioaddr + SDHCI_VENDOR_SPEC);
+			v &= ~SDHCI_VENDOR_SPEC_SDIO_QUIRK;
+			writel(v, host->ioaddr + SDHCI_VENDOR_SPEC);
+	}
+
 	writel(val, host->ioaddr + reg);
 }
 
@@ -103,9 +130,21 @@ static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
 		 * Postpone this write, we must do it together with a
 		 * command write that is down below.
 		 */
+		if ((imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT)
+				&& (host->cmd->opcode == SD_IO_RW_EXTENDED)
+				&& (host->cmd->data->blocks > 1)
+				&& (host->cmd->data->flags & MMC_DATA_READ)) {
+			u32 v;
+			v = readl(host->ioaddr + SDHCI_VENDOR_SPEC);
+			v |= SDHCI_VENDOR_SPEC_SDIO_QUIRK;
+			writel(v, host->ioaddr + SDHCI_VENDOR_SPEC);
+		}
 		imx_data->scratchpad = val;
 		return;
 	case SDHCI_COMMAND:
+		if ((host->cmd->opcode == MMC_STOP_TRANSMISSION)
+			&& (imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT))
+			val |= SDHCI_CMD_ABORTCMD;
 		writel(val << 16 | imx_data->scratchpad,
 			host->ioaddr + SDHCI_TRANSFER_MODE);
 		return;
@@ -213,6 +252,9 @@ static int esdhc_pltfm_init(struct sdhci_host *host, struct sdhci_pltfm_data *pd
 		sdhci_esdhc_ops.get_ro = esdhc_pltfm_get_ro;
 	}
 
+	if (!(cpu_is_mx25() || cpu_is_mx35() || cpu_is_mx51()))
+		imx_data->flags |= ESDHC_FLAG_MULTIBLK_NO_INT;
+
 	if (boarddata) {
 		err = gpio_request_one(boarddata->wp_gpio, GPIOF_IN, "ESDHC_WP");
 		if (err) {
-- 
1.7.1





More information about the linux-arm-kernel mailing list