[PATCH 2/2] s5pc110: add MIPI-DSI controller driver.

Kukjin Kim kgene.kim at samsung.com
Thu Mar 17 04:43:12 EDT 2011


Inki Dae wrote:
> 
> S5PC110 and S5PC210 SoC platform have one or two MIPI-DSI controller.
> MIPI-DSI controller can be used to connect MIPI-DSI based LCD Panel.
> this patch adds MIPI-DSI controller driver.
> 
> to use this driver, MIPI-DSI based LCD panel driver have to register
> mipi_dsim_lcd_driver object to MIPI-DSI driver and then when MIPI-DSI
> driver is probed, probe callback of LCD panel driver registered would
> be called.
> 
> Signed-off-by: Inki Dae <inki.dae at samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park at samsung.com>
> ---
>  arch/arm/plat-s5p/include/plat/dsim.h      |  357 ++++++++++++++++
>  arch/arm/plat-s5p/include/plat/regs-dsim.h |  141 ++++++
>  drivers/video/Kconfig                      |    7 +
>  drivers/video/Makefile                     |    2 +
>  drivers/video/s5p_mipi_dsi.c               |  428 +++++++++++++++++++
>  drivers/video/s5p_mipi_dsi_common.c        |  635
> ++++++++++++++++++++++++++++
>  drivers/video/s5p_mipi_dsi_common.h        |   38 ++
>  drivers/video/s5p_mipi_dsi_lowlevel.c      |  553
++++++++++++++++++++++++
>  drivers/video/s5p_mipi_dsi_lowlevel.h      |   98 +++++
>  9 files changed, 2259 insertions(+), 0 deletions(-)
>  create mode 100644 arch/arm/plat-s5p/include/plat/dsim.h
>  create mode 100644 arch/arm/plat-s5p/include/plat/regs-dsim.h
>  create mode 100644 drivers/video/s5p_mipi_dsi.c
>  create mode 100644 drivers/video/s5p_mipi_dsi_common.c
>  create mode 100644 drivers/video/s5p_mipi_dsi_common.h
>  create mode 100644 drivers/video/s5p_mipi_dsi_lowlevel.c
>  create mode 100644 drivers/video/s5p_mipi_dsi_lowlevel.h
> 
Hi,

There are some comments.

There is no reason why "dsim.h" is in plat directory because it includes
everything but it has no dependency on platform. I think, if it is used on
machine or platform, should be separated and how about mipi_dsim.h like
plat/mipi_csis.h?

I'm a little confusing for the word between "dsim" and "dsi". Would be
better if you could use just one such as "csis".

Is find_mipi_client_registered() used for finding LCD panel? If so, where
does it look for it?

As you know, EXYNOS4210 has 2 MIPI DSI Master channels. So could you please
let me know how to support it?

Thanks.

Best regards,
Kgene.
--
Kukjin Kim <kgene.kim at samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.

> diff --git a/arch/arm/plat-s5p/include/plat/dsim.h b/arch/arm/plat-
> s5p/include/plat/dsim.h
> new file mode 100644
> index 0000000..9aa5a93
> --- /dev/null
> +++ b/arch/arm/plat-s5p/include/plat/dsim.h
> @@ -0,0 +1,357 @@
> +/* linux/arm/arch/plat-s5p/include/plat/dsim.h
> + *
> + * Platform data header for Samsung SoC MIPI-DSIM.
> + *
> + * Copyright (c) 2009 Samsung Electronics
> + * InKi Dae <inki.dae at samsung.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> +*/
> +
> +#ifndef _DSIM_H
> +#define _DSIM_H
> +
> +#include <linux/device.h>
> +#include <linux/fb.h>
> +
> +#define PANEL_NAME_SIZE		(32)
> +
> +enum mipi_dsim_interface_type {
> +	DSIM_COMMAND,
> +	DSIM_VIDEO
> +};
> +
> +enum mipi_dsim_virtual_ch_no {
> +	DSIM_VIRTUAL_CH_0,
> +	DSIM_VIRTUAL_CH_1,
> +	DSIM_VIRTUAL_CH_2,
> +	DSIM_VIRTUAL_CH_3
> +};
> +
> +enum mipi_dsim_burst_mode_type {
> +	DSIM_NON_BURST_SYNC_EVENT,
> +	DSIM_NON_BURST_SYNC_PULSE = 2,
> +	DSIM_BURST,
> +	DSIM_NON_VIDEO_MODE
> +};
> +
> +enum mipi_dsim_no_of_data_lane {
> +	DSIM_DATA_LANE_1,
> +	DSIM_DATA_LANE_2,
> +	DSIM_DATA_LANE_3,
> +	DSIM_DATA_LANE_4
> +};
> +
> +enum mipi_dsim_byte_clk_src {
> +	DSIM_PLL_OUT_DIV8,
> +	DSIM_EXT_CLK_DIV8,
> +	DSIM_EXT_CLK_BYPASS
> +};
> +
> +enum mipi_dsim_pixel_format {
> +	DSIM_CMD_3BPP,
> +	DSIM_CMD_8BPP,
> +	DSIM_CMD_12BPP,
> +	DSIM_CMD_16BPP,
> +	DSIM_VID_16BPP_565,
> +	DSIM_VID_18BPP_666PACKED,
> +	DSIM_18BPP_666LOOSELYPACKED,
> +	DSIM_24BPP_888
> +};
> +
> +/**
> + * struct mipi_dsim_config - interface for configuring mipi-dsi
controller.
> + *
> + * @auto_flush: enable or disable Auto flush of MD FIFO using VSYNC
pulse.
> + * @eot_disable: enable or disable EoT packet in HS mode.
> + * @auto_vertical_cnt: specifies auto vertical count mode.
> + *	in Video mode, the vertical line transition uses line counter
> + *	configured by VSA, VBP, and Vertical resolution.
> + *	If this bit is set to '1', the line counter does not use VSA and VBP
> + *	registers.(in command mode, this variable is ignored)
> + * @hse: set horizontal sync event mode.
> + *	In VSYNC pulse and Vporch area, MIPI DSI master transfers only HSYNC
> + *	start packet to MIPI DSI slave at MIPI DSI spec1.1r02.
> + *	this bit transfers HSYNC end packet in VSYNC pulse and Vporch area
> + *	(in mommand mode, this variable is ignored)
> + * @hfp: specifies HFP disable mode.
> + *	if this variable is set, DSI master ignores HFP area in VIDEO mode.
> + *	(in command mode, this variable is ignored)
> + * @hbp: specifies HBP disable mode.
> + *	if this variable is set, DSI master ignores HBP area in VIDEO mode.
> + *	(in command mode, this variable is ignored)
> + * @hsa: specifies HSA disable mode.
> + *	if this variable is set, DSI master ignores HSA area in VIDEO mode.
> + *	(in command mode, this variable is ignored)
> + * @e_interface: specifies interface to be used.(CPU or RGB interface)
> + * @e_virtual_ch: specifies virtual channel number that main or
> + *	sub diaplsy uses.
> + * @e_pixel_format: specifies pixel stream format for main or sub
display.
> + * @e_burst_mode: selects Burst mode in Video mode.
> + *	in Non-burst mode, RGB data area is filled with RGB data and NULL
> + *	packets, according to input bandwidth of RGB interface.
> + *	In Burst mode, RGB data area is filled with RGB data only.
> + * @e_no_data_lane: specifies data lane count to be used by Master.
> + * @e_byte_clk: select byte clock source. (it must be DSIM_PLL_OUT_DIV8)
> + *	DSIM_EXT_CLK_DIV8 and DSIM_EXT_CLK_BYPASSS are not supported.
> + * @pll_stable_time: specifies the PLL Timer for stability of the
ganerated
> + *	clock(System clock cycle base)
> + *	if the timer value goes to 0x00000000, the clock stable bit of
status
> + *	and interrupt register is set.
> + * @esc_clk: specifies escape clock frequency for getting the escape
clock
> + *	prescaler value.
> + * @stop_holding_cnt: specifies the interval value between transmitting
> + *	read packet(or write "set_tear_on" command) and BTA request.
> + *	after transmitting read packet or write "set_tear_on" command,
> + *	BTA requests to D-PHY automatically. this counter value specifies
> + *	the interval between them.
> + * @bta_timeout: specifies the timer for BTA.
> + *	this register specifies time out from BTA request to change
> + *	the direction with respect to Tx escape clock.
> + * @rx_timeout: specifies the timer for LP Rx mode timeout.
> + *	this register specifies time out on how long RxValid deasserts,
> + *	after RxLpdt asserts with respect to Tx escape clock.
> + *	- RxValid specifies Rx data valid indicator.
> + *	- RxLpdt specifies an indicator that D-PHY is under RxLpdt mode.
> + *	- RxValid and RxLpdt specifies signal from D-PHY.
> + * @lcd_panel_info: pointer for lcd panel specific structure.
> + *	this structure specifies width, height, timing and polarity and so
on.
> + * @mipi_ddi_pd: pointer to lcd panel platform data.
> + */
> +struct mipi_dsim_config {
> +	unsigned char auto_flush;
> +	unsigned char eot_disable;
> +
> +	unsigned char auto_vertical_cnt;
> +	unsigned char hse;
> +	unsigned char hfp;
> +	unsigned char hbp;
> +	unsigned char hsa;
> +
> +	enum mipi_dsim_interface_type	e_interface;
> +	enum mipi_dsim_virtual_ch_no	e_virtual_ch;
> +	enum mipi_dsim_pixel_format	e_pixel_format;
> +	enum mipi_dsim_burst_mode_type	e_burst_mode;
> +	enum mipi_dsim_no_of_data_lane	e_no_data_lane;
> +	enum mipi_dsim_byte_clk_src	e_byte_clk;
> +
> +	/*
> +	 * ===========================================
> +	 * |    P    |    M    |    S    |    MHz    |
> +	 * -------------------------------------------
> +	 * |    3    |   100   |    3    |    100    |
> +	 * |    3    |   100   |    2    |    200    |
> +	 * |    3    |    63   |    1    |    252    |
> +	 * |    4    |   100   |    1    |    300    |
> +	 * |    4    |   110   |    1    |    330    |
> +	 * |   12    |   350   |    1    |    350    |
> +	 * |    3    |   100   |    1    |    400    |
> +	 * |    4    |   150   |    1    |    450    |
> +	 * |    3    |   118   |    1    |    472    |
> +	 * |   12    |   250   |    0    |    500    |
> +	 * |    4    |   100   |    0    |    600    |
> +	 * |    3    |    81   |    0    |    648    |
> +	 * |    3    |    88   |    0    |    704    |
> +	 * |    3    |    90   |    0    |    720    |
> +	 * |    3    |   100   |    0    |    800    |
> +	 * |   12    |   425   |    0    |    850    |
> +	 * |    4    |   150   |    0    |    900    |
> +	 * |   12    |   475   |    0    |    950    |
> +	 * |    6    |   250   |    0    |   1000    |
> +	 * -------------------------------------------
> +	 */
> +	unsigned char p;
> +	unsigned short m;
> +	unsigned char s;
> +
> +	unsigned int pll_stable_time;
> +	unsigned long esc_clk;
> +
> +	unsigned short stop_holding_cnt;
> +	unsigned char bta_timeout;
> +	unsigned short rx_timeout;
> +
> +	void *lcd_panel_info;
> +	void *dsim_ddi_pd;
> +};
> +
> +/**
> + * struct mipi_dsim_device - global interface for mipi-dsi driver.
> + *
> + * @dev: driver model representation of the device.
> + * @clock: pointer to MIPI-DSI clock of clock framework.
> + * @irq: interrupt number to MIPI-DSI controller.
> + * @reg_base: base address to memory mapped SRF of MIPI-DSI controller.
> + *	(virtual address)
> + * @pd: pointer to MIPI-DSI driver platform data.
> + * @dsim_info: infomation for configuring mipi-dsi controller.
> + * @master_ops: callbacks to mipi-dsi operations.
> + * @lcd_info: pointer to mipi_lcd_info structure.
> + * @state: specifies status of MIPI-DSI controller.
> + *	the status could be RESET, INIT, STOP, HSCLKEN and ULPS.
> + * @resume_complete: indicates whether resume operation is completed or
not.
> + * @data_lane: specifiec enabled data lane number.
> + *	this variable would be set by driver according to e_no_data_lane
> + *	automatically.
> + * @e_clk_src: select byte clock source.
> + *	this variable would be set by driver according to e_byte_clock
> + *	automatically.
> + * @hs_clk: HS clock rate.
> + *	this variable would be set by driver automatically.
> + * @byte_clk: Byte clock rate.
> + *	this variable would be set by driver automatically.
> + * @escape_clk: ESCAPE clock rate.
> + *	this variable would be set by driver automatically.
> + * @freq_band: indicates Bitclk frequency band for D-PHY global timing.
> + *	Serial Clock(=ByteClk X 8)		FreqBand[3:0]
> + *		~ 99.99 MHz				0000
> + *		100 ~ 119.99 MHz			0001
> + *		120 ~ 159.99 MHz			0010
> + *		160 ~ 199.99 MHz			0011
> + *		200 ~ 239.99 MHz			0100
> + *		140 ~ 319.99 MHz			0101
> + *		320 ~ 389.99 MHz			0110
> + *		390 ~ 449.99 MHz			0111
> + *		450 ~ 509.99 MHz			1000
> + *		510 ~ 559.99 MHz			1001
> + *		560 ~ 639.99 MHz			1010
> + *		640 ~ 689.99 MHz			1011
> + *		690 ~ 769.99 MHz			1100
> + *		770 ~ 869.99 MHz			1101
> + *		870 ~ 949.99 MHz			1110
> + *		950 ~ 1000 MHz				1111
> + *	this variable would be calculated by driver automatically.
> + */
> +struct mipi_dsim_device {
> +	struct device *dev;
> +	struct resource *res;
> +	struct clk *clock;
> +	unsigned int irq;
> +	void __iomem *reg_base;
> +
> +	struct s5p_platform_mipi_dsim *pd;
> +	struct mipi_dsim_config *dsim_config;
> +	struct mipi_dsim_master_ops *master_ops;
> +	struct mipi_dsim_ddi *dsim_ddi;
> +
> +	unsigned int state;
> +	unsigned int resume_complete;
> +	unsigned int data_lane;
> +	enum mipi_dsim_byte_clk_src e_clk_src;
> +	unsigned long hs_clk;
> +	unsigned long byte_clk;
> +	unsigned long escape_clk;
> +	unsigned char freq_band;
> +};
> +
> +/**
> + * struct s5p_platform_mipi_dsim - interface to platform data
> + *	for mipi-dsi driver.
> + *
> + * @lcd_panel_name: specifies lcd panel name registered to mipi-dsi
driver.
> + *	lcd panel driver searched would be actived.
> + * @dsim_config: pointer of structure for configuring mipi-dsi
controller.
> + * @dsim_lcd_info: pointer to structure for configuring
> + *	mipi-dsi based lcd panel.
> + * @mipi_power: callback pointer for enabling or disabling mipi power.
> + * @part_reset: callback pointer for reseting mipi phy.
> + * @init_d_phy: callback pointer for enabing d_phy of dsi master.
> + * @get_fb_frame_done: callback pointer for getting frame done status of
the
> + *	display controller(FIMD).
> + * @trigger: callback pointer for triggering display controller(FIMD)
> + *	in case of CPU mode.
> + * @delay_for_stabilization: specifies stable time.
> + *	this delay needs when writing data on SFR
> + *	after mipi mode became LP mode.
> + */
> +struct s5p_platform_mipi_dsim {
> +	char	lcd_panel_name[PANEL_NAME_SIZE];
> +
> +	struct mipi_dsim_config *dsim_config;
> +	struct mipi_dsim_lcd_config *dsim_lcd_config;
> +
> +	unsigned int delay_for_stabilization;
> +
> +	int (*mipi_power) (struct mipi_dsim_device *dsim, unsigned int
enable);
> +	int (*part_reset) (struct mipi_dsim_device *dsim);
> +	int (*init_d_phy) (struct mipi_dsim_device *dsim);
> +	int (*get_fb_frame_done) (struct fb_info *info);
> +	void (*trigger) (struct fb_info *info);
> +};
> +/**
> + * struct mipi_dsim_master_ops - callbacks to mipi-dsi operations.
> + *
> + * @cmd_write: transfer command to lcd panel at LP mode.
> + * @cmd_read: read command from rx register.
> + * @get_dsim_frame_done: get the status that all screen data have been
> + *	transferred to mipi-dsi.
> + * @clear_dsim_frame_done: clear frame done status.
> + * @change_dsim_transfer_mode: change transfer mode to LP or HS mode.
> + *	- LP mode is used when commands data ard transferred to lcd panel.
> + * @get_fb_frame_done: get frame done status of display controller.
> + * @trigger: trigger display controller.
> + *	- this one would be used only in case of CPU mode.
> + */
> +
> +struct mipi_dsim_master_ops {
> +	int (*cmd_write) (struct mipi_dsim_device *dsim, unsigned int
data_id,
> +		unsigned int data0, unsigned int data1);
> +	int (*cmd_read) (struct mipi_dsim_device *dsim, unsigned int
data_id,
> +		unsigned int data0, unsigned int data1);
> +	int (*get_dsim_frame_done) (struct mipi_dsim_device *dsim);
> +	int (*clear_dsim_frame_done) (struct mipi_dsim_device *dsim);
> +
> +	int (*change_dsim_transfer_mode) (struct mipi_dsim_device *dsim,
> +						unsigned int mode);
> +
> +	int (*get_fb_frame_done) (struct fb_info *info);
> +	void (*trigger) (struct fb_info *info);
> +};
> +
> +/**
> + * device structure for mipi-dsi based lcd panel.
> + *
> + * @dev: driver model representation of the device.
> + * @id: id of device registered and when device is registered
> + *	id would be counted.
> + * @modalias: name of the driver to use with this device, or an
> + *	alias for that name.
> + * @mipi_lcd_drv: pointer of mipi_lcd_driver.
> + * @master: pointer to dsim_device.
> + */
> +struct mipi_dsim_lcd_device {
> +	struct	device	dev;
> +	int	id;
> +	char	modalias[64];
> +
> +	struct mipi_dsim_lcd_driver	*dsim_drv;
> +	struct mipi_dsim_device		*master;
> +};
> +
> +/**
> + * driver structure for mipi-dsi based lcd panel.
> + *
> + * this structure should be registered by lcd panel driver.
> + * mipi-dsi driver seeks lcd panel registered through name field
> + * and calls these callback functions in appropriate time.
> + */
> +struct mipi_dsim_lcd_driver {
> +	char		*name;
> +
> +	int	(*probe)(struct mipi_dsim_lcd_device *dsim_dev);
> +	int	(*remove)(struct mipi_dsim_lcd_device *dsim_dev);
> +	void	(*shutdown)(struct mipi_dsim_lcd_device *dsim_dev);
> +	int	(*suspend)(struct mipi_dsim_lcd_device *dsim_dev);
> +	int	(*resume)(struct mipi_dsim_lcd_device *dsim_dev);
> +};
> +
> +/**
> + * register mipi_dsim_lcd_driver object defined by lcd panel driver
> + * to mipi-dsi driver.
> + */
> +extern int s5p_mipi_dsi_register_lcd_driver(struct mipi_dsim_lcd_driver
> +						*lcd_drv);
> +
> +#endif /* _DSIM_H */
> diff --git a/arch/arm/plat-s5p/include/plat/regs-dsim.h b/arch/arm/plat-
> s5p/include/plat/regs-dsim.h
> new file mode 100644
> index 0000000..7ef5a2f
> --- /dev/null
> +++ b/arch/arm/plat-s5p/include/plat/regs-dsim.h
> @@ -0,0 +1,141 @@
> +/* linux/arch/arm/plat-s5p/include/plat/regs-dsim.h
> + *
> + * Register definition file for Samsung MIPI-DSIM driver
> + *
> + * InKi Dae <inki.dae at samsung.com>, Copyright (c) 2009 Samsung
Electronics
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> +*/
> +
> +#ifndef _REGS_DSIM_H
> +#define _REGS_DSIM_H
> +
> +#define S5P_DSIM_STATUS		(0x0)	/* Status register */
> +#define S5P_DSIM_SWRST		(0x4)	/* Software reset register
*/
> +#define S5P_DSIM_CLKCTRL	(0x8)	/* Clock control register */
> +#define S5P_DSIM_TIMEOUT	(0xc)	/* Time out register */
> +#define S5P_DSIM_CONFIG		(0x10)	/* Configuration register */
> +#define S5P_DSIM_ESCMODE	(0x14)	/* Escape mode register */
> +
> +/* Main display image resolution register */
> +#define S5P_DSIM_MDRESOL	(0x18)
> +#define S5P_DSIM_MVPORCH	(0x1c)	/* Main display Vporch register */
> +#define S5P_DSIM_MHPORCH	(0x20)	/* Main display Hporch register */
> +#define S5P_DSIM_MSYNC		(0x24)	/* Main display sync area
> register */
> +
> +/* Sub display image resolution register */
> +#define S5P_DSIM_SDRESOL	(0x28)
> +#define S5P_DSIM_INTSRC		(0x2c)	/* Interrupt source register
*/
> +#define S5P_DSIM_INTMSK		(0x30)	/* Interrupt mask register
*/
> +#define S5P_DSIM_PKTHDR		(0x34)	/* Packet Header FIFO
register
> */
> +#define S5P_DSIM_PAYLOAD	(0x38)	/* Payload FIFO register */
> +#define S5P_DSIM_RXFIFO		(0x3c)	/* Read FIFO register */
> +#define S5P_DSIM_FIFOTHLD	(0x40)	/* FIFO threshold level register */
> +#define S5P_DSIM_FIFOCTRL	(0x44)	/* FIFO status and control register
*/
> +
> +/* FIFO memory AC characteristic register */
> +#define S5P_DSIM_PLLCTRL	(0x4c)	/* PLL control register */
> +#define S5P_DSIM_PLLTMR		(0x50)	/* PLL timer register */
> +#define S5P_DSIM_PHYACCHR	(0x54)	/* D-PHY AC characteristic register
*/
> +#define S5P_DSIM_PHYACCHR1	(0x58)	/* D-PHY AC characteristic register1
*/
> +
> +/* DSIM_STATUS */
> +#define DSIM_STOP_STATE_DAT(x)	(((x) & 0xf) << 0)
> +#define DSIM_STOP_STATE_CLK	(1 << 8)
> +#define DSIM_TX_READY_HS_CLK	(1 << 10)
> +
> +/* DSIM_SWRST */
> +#define DSIM_FUNCRST		(1 << 16)
> +#define DSIM_SWRST		(1 << 0)
> +
> +/* S5P_DSIM_TIMEOUT */
> +#define DSIM_LPDR_TOUT_SHIFT	(0)
> +#define DSIM_BTA_TOUT_SHIFT	(16)
> +
> +/* S5P_DSIM_CLKCTRL */
> +#define DSIM_LANE_ESC_CLKEN_SHIFT	(19)
> +#define DSIM_BYTE_CLKEN_SHIFT		(24)
> +#define DSIM_BYTE_CLK_SRC_SHIFT		(25)
> +#define DSIM_PLL_BYPASS_SHIFT		(27)
> +#define DSIM_ESC_CLKEN_SHIFT		(28)
> +#define DSIM_TX_REQUEST_HSCLK_SHIFT	(31)
> +#define DSIM_LANE_ESC_CLKEN(x)		(((x) & 0x1f) << \
> +						DSIM_LANE_ESC_CLKEN_SHIFT)
> +#define DSIM_BYTE_CLK_ENABLE		(1 << DSIM_BYTE_CLKEN_SHIFT)
> +#define DSIM_BYTE_CLK_DISABLE		(0 << DSIM_BYTE_CLKEN_SHIFT)
> +#define DSIM_PLL_BYPASS_EXTERNAL	(1 << DSIM_PLL_BYPASS_SHIFT)
> +#define DSIM_ESC_CLKEN_ENABLE		(1 << DSIM_ESC_CLKEN_SHIFT)
> +#define DSIM_ESC_CLKEN_DISABLE		(0 << DSIM_ESC_CLKEN_SHIFT)
> +
> +/* S5P_DSIM_CONFIG */
> +#define DSIM_NUM_OF_DATALANE_SHIFT	(5)
> +#define DSIM_HSA_MODE_SHIFT		(20)
> +#define DSIM_HBP_MODE_SHIFT		(21)
> +#define DSIM_HFP_MODE_SHIFT		(22)
> +#define DSIM_HSE_MODE_SHIFT		(23)
> +#define DSIM_AUTO_MODE_SHIFT		(24)
> +#define DSIM_LANE_ENx(x)		(((x) & 0x1f) << 0)
> +
> +#define DSIM_NUM_OF_DATA_LANE(x)	((x) << DSIM_NUM_OF_DATALANE_SHIFT)
> +
> +/* S5P_DSIM_ESCMODE */
> +#define DSIM_TX_LPDT_SHIFT		(6)
> +#define DSIM_CMD_LPDT_SHIFT		(7)
> +#define DSIM_TX_LPDT_LP			(1 << DSIM_TX_LPDT_SHIFT)
> +#define DSIM_CMD_LPDT_LP		(1 << DSIM_CMD_LPDT_SHIFT)
> +#define DSIM_STOP_STATE_CNT_SHIFT	(21)
> +#define DSIM_FORCE_STOP_STATE_SHIFT	(20)
> +
> +/* S5P_DSIM_MDRESOL */
> +#define DSIM_MAIN_STAND_BY		(1 << 31)
> +#define DSIM_MAIN_VRESOL(x)		(((x) & 0x7ff) << 16)
> +#define DSIM_MAIN_HRESOL(x)		(((x) & 0X7ff) << 0)
> +
> +/* S5P_DSIM_MVPORCH */
> +#define DSIM_CMD_ALLOW_SHIFT		(28)
> +#define DSIM_STABLE_VFP_SHIFT		(16)
> +#define DSIM_MAIN_VBP_SHIFT		(0)
> +#define DSIM_CMD_ALLOW_MASK		(0xf << DSIM_CMD_ALLOW_SHIFT)
> +#define DSIM_STABLE_VFP_MASK		(0x7ff << DSIM_STABLE_VFP_SHIFT)
> +#define DSIM_MAIN_VBP_MASK		(0x7ff << DSIM_MAIN_VBP_SHIFT)
> +
> +/* S5P_DSIM_MHPORCH */
> +#define DSIM_MAIN_HFP_SHIFT		(16)
> +#define DSIM_MAIN_HBP_SHIFT		(0)
> +#define DSIM_MAIN_HFP_MASK		((0xffff) << DSIM_MAIN_HFP_SHIFT)
> +#define DSIM_MAIN_HBP_MASK		((0xffff) << DSIM_MAIN_HBP_SHIFT)
> +
> +/* S5P_DSIM_MSYNC */
> +#define DSIM_MAIN_VSA_SHIFT		(22)
> +#define DSIM_MAIN_HSA_SHIFT		(0)
> +#define DSIM_MAIN_VSA_MASK		((0x3ff) << DSIM_MAIN_VSA_SHIFT)
> +#define DSIM_MAIN_HSA_MASK		((0xffff) << DSIM_MAIN_HSA_SHIFT)
> +
> +/* S5P_DSIM_SDRESOL */
> +#define DSIM_SUB_STANDY_SHIFT		(31)
> +#define DSIM_SUB_VRESOL_SHIFT		(16)
> +#define DSIM_SUB_HRESOL_SHIFT		(0)
> +#define DSIM_SUB_STANDY_MASK		((0x1) << DSIM_SUB_STANDY_SHIFT)
> +#define DSIM_SUB_VRESOL_MASK		((0x7ff) << DSIM_SUB_VRESOL_SHIFT)
> +#define DSIM_SUB_HRESOL_MASK		((0x7ff) << DSIM_SUB_HRESOL_SHIFT)
> +
> +/* S5P_DSIM_INTSRC */
> +#define INTSRC_FRAME_DONE		(1 << 24)
> +#define INTSRC_PLL_STABLE		(1 << 31)
> +
> +/* S5P_DSIM_INTMSK */
> +#define INTMSK_FRAME_DONE		(1 << 24)
> +
> +/* S5P_DSIM_FIFOCTRL */
> +#define SFR_HEADER_EMPTY		(1 << 22)
> +
> +/* S5P_DSIM_PHYACCHR */
> +#define DSIM_AFC_CTL(x)			(((x) & 0x7) << 5)
> +
> +/* S5P_DSIM_PLLCTRL */
> +#define DSIM_PLL_EN_SHIFT		(23)
> +#define DSIM_FREQ_BAND_SHIFT		(24)
> +
> +#endif /* _REGS_DSIM_H */
> diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
> index 932e7bb..9744e32 100644
> --- a/drivers/video/Kconfig
> +++ b/drivers/video/Kconfig
> @@ -2098,6 +2098,13 @@ config FB_S3C2410_DEBUG
>  	  Turn on debugging messages. Note that you can set/unset at run
time
>  	  through sysfs
> 
> +config S5P_MIPI_DSI
> +	tristate "Samsung SoC MIPI-DSI support."
> +	depends on FB_S3C && ARCH_S5PV210
> +	default n
> +	---help---
> +	  This enables support for MIPI-DSI device.
> +
>  config FB_NUC900
>          bool "NUC900 LCD framebuffer support"
>          depends on FB && ARCH_W90X900
> diff --git a/drivers/video/Makefile b/drivers/video/Makefile
> index 36aca21..12052a2 100644
> --- a/drivers/video/Makefile
> +++ b/drivers/video/Makefile
> @@ -119,6 +119,8 @@ obj-$(CONFIG_FB_SH7760)		  += sh7760fb.o
>  obj-$(CONFIG_FB_IMX)              += imxfb.o
>  obj-$(CONFIG_FB_S3C)		  += s3c-fb.o
>  obj-$(CONFIG_FB_S3C2410)	  += s3c2410fb.o
> +obj-$(CONFIG_S5P_MIPI_DSI)	  += s5p_mipi_dsi.o s5p_mipi_dsi_common.o \
> +				     s5p_mipi_dsi_lowlevel.o
>  obj-$(CONFIG_FB_FSL_DIU)	  += fsl-diu-fb.o
>  obj-$(CONFIG_FB_COBALT)           += cobalt_lcdfb.o
>  obj-$(CONFIG_FB_PNX4008_DUM)	  += pnx4008/
> diff --git a/drivers/video/s5p_mipi_dsi.c b/drivers/video/s5p_mipi_dsi.c
> new file mode 100644
> index 0000000..0bd9a44
> --- /dev/null
> +++ b/drivers/video/s5p_mipi_dsi.c
> @@ -0,0 +1,428 @@
> +/* linux/drivers/video/s5p_mipi_dsi.c
> + *
> + * Samsung SoC MIPI-DSIM driver.
> + *
> + * InKi Dae, <inki.dae at samsung.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> +*/
> +
> +#include <linux/module.h>
> +#include <linux/kernel.h>
> +#include <linux/errno.h>
> +#include <linux/clk.h>
> +#include <linux/mutex.h>
> +#include <linux/wait.h>
> +#include <linux/fs.h>
> +#include <linux/mm.h>
> +#include <linux/fb.h>
> +#include <linux/ctype.h>
> +#include <linux/platform_device.h>
> +#include <linux/io.h>
> +#include <linux/irq.h>
> +#include <linux/memory.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/kthread.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/notifier.h>
> +
> +#include <plat/fb.h>
> +#include <plat/regs-dsim.h>
> +#include <plat/dsim.h>
> +
> +#include <mach/map.h>
> +
> +#include "s5p_mipi_dsi_common.h"
> +
> +#define master_to_driver(a)	(a->dsim_ddi->dsim_lcd_drv)
> +#define master_to_device(a)	(a->dsim_ddi->dsim_lcd_dev)
> +#define set_master_to_device(a)	(a->dsim_ddi->dsim_lcd_dev->master =
a)
> +
> +struct mipi_dsim_ddi {
> +	struct list_head		list;
> +	struct mipi_dsim_lcd_driver	*dsim_lcd_drv;
> +	struct mipi_dsim_lcd_device	*dsim_lcd_dev;
> +};
> +
> +static LIST_HEAD(dsim_ddi_list);
> +static DEFINE_MUTEX(mipi_lock);
> +
> +static struct s5p_platform_mipi_dsim *to_dsim_plat(struct platform_device
> *pdev)
> +{
> +	return (struct s5p_platform_mipi_dsim *)pdev->dev.platform_data;
> +}
> +
> +static irqreturn_t s5p_mipi_dsi_interrupt_handler(int irq, void *dev_id)
> +{
> +	return IRQ_HANDLED;
> +}
> +
> +int s5p_mipi_dsi_register_lcd_driver(struct mipi_dsim_lcd_driver
*lcd_drv)
> +{
> +	struct mipi_dsim_ddi *dsim_ddi;
> +	struct mipi_dsim_lcd_device *dsim_lcd_dev;
> +	static unsigned int id;
> +	int ret;
> +
> +	dsim_ddi = kzalloc(sizeof(struct mipi_dsim_ddi), GFP_KERNEL);
> +	if (!dsim_ddi) {
> +		printk(KERN_ERR "failed to allocate dsim_ddi object.\n");
> +		return -EFAULT;
> +	}
> +
> +	dsim_ddi->dsim_lcd_drv = lcd_drv;
> +
> +	dsim_lcd_dev = kzalloc(sizeof(struct mipi_dsim_lcd_device),
> GFP_KERNEL);
> +	if (!dsim_lcd_dev) {
> +		printk(KERN_ERR "failed to allocate dsim_lcd_dev
object.\n");
> +		ret = -EFAULT;
> +		goto err_dsim;
> +	}
> +
> +	mutex_lock(&mipi_lock);
> +
> +	dsim_lcd_dev->id = id++;
> +	dsim_ddi->dsim_lcd_dev = dsim_lcd_dev;
> +
> +	device_initialize(&dsim_lcd_dev->dev);
> +
> +	strcpy(dsim_lcd_dev->modalias, lcd_drv->name);
> +
> +	dev_set_name(&dsim_lcd_dev->dev, "mipi-dsi.%d\n", dsim_lcd_dev->id);
> +
> +	ret = device_add(&dsim_lcd_dev->dev);
> +	if (ret < 0) {
> +		printk(KERN_ERR "can't %s %s, status %d\n",
> +				"add", dev_name(&dsim_lcd_dev->dev), ret);
> +		id--;
> +		goto err_device_add;
> +	}
> +
> +	list_add_tail(&dsim_ddi->list, &dsim_ddi_list);
> +
> +	mutex_unlock(&mipi_lock);
> +
> +	printk(KERN_DEBUG "registered panel driver(%s) to mipi-dsi
driver.\n",
> +		lcd_drv->name);
> +
> +	return ret;
> +
> +err_device_add:
> +	kfree(dsim_lcd_dev);
> +
> +err_dsim:
> +	kfree(dsim_ddi);
> +
> +	return ret;
> +}
> +
> +/*
> + * This function is a wrapper for changing transfer mode.
> + * It is used for the panel driver before and after changing gamma value.
> + */
> +static int s5p_mipi_dsi_change_transfer_mode(struct mipi_dsim_device
*dsim,
> +		unsigned int mode)
> +{
> +	if (mode < 0 || mode > 1) {
> +		dev_err(dsim->dev, "mode range should be 0 or 1.\n");
> +		return -EINVAL;
> +	}
> +
> +	s5p_mipi_dsi_set_data_transfer_mode(dsim, mode);
> +
> +	return 0;
> +}
> +
> +static struct mipi_dsim_ddi *find_mipi_client_registered
> +		(struct mipi_dsim_device *dsim, const char *name)
> +{
> +	struct mipi_dsim_ddi *dsim_ddi;
> +	struct mipi_dsim_lcd_driver *dsim_lcd_drv = NULL;
> +
> +	mutex_lock(&mipi_lock);
> +
> +	dev_dbg(dsim->dev, "find lcd panel driver(%s).\n",
> +		name);
> +
> +	list_for_each_entry(dsim_ddi, &dsim_ddi_list, list) {
> +		dsim_lcd_drv = dsim_ddi->dsim_lcd_drv;
> +
> +		if ((strcmp(dsim_lcd_drv->name, name)) == 0) {
> +			mutex_unlock(&mipi_lock);
> +			dev_dbg(dsim->dev, "found!!!(%s).\n",
> +				dsim_lcd_drv->name);
> +			return dsim_ddi;
> +		}
> +	}
> +
> +	dev_warn(dsim->dev, "failed to find lcd panel driver(%s).\n",
> +		name);
> +
> +	mutex_unlock(&mipi_lock);
> +
> +	return NULL;
> +}
> +
> +/* define MIPI-DSI Master operations. */
> +static struct mipi_dsim_master_ops master_ops = {
> +	.cmd_write			= s5p_mipi_dsi_wr_data,
> +	.get_dsim_frame_done		=
s5p_mipi_dsi_get_frame_done_status,
> +	.clear_dsim_frame_done		= s5p_mipi_dsi_clear_frame_done,
> +	.change_dsim_transfer_mode	= s5p_mipi_dsi_change_transfer_mode,
> +};
> +
> +static int s5p_mipi_dsi_probe(struct platform_device *pdev)
> +{
> +	struct resource *res;
> +	struct mipi_dsim_device *dsim;
> +	struct mipi_dsim_config *dsim_config;
> +	struct s5p_platform_mipi_dsim *dsim_pd;
> +	int ret = -1;
> +
> +	dsim = kzalloc(sizeof(struct mipi_dsim_device), GFP_KERNEL);
> +	if (!dsim) {
> +		dev_err(&pdev->dev, "failed to allocate dsim object.\n");
> +		return -EFAULT;
> +	}
> +
> +	dsim->pd = to_dsim_plat(pdev);
> +	dsim->dev = &pdev->dev;
> +	dsim->resume_complete = 0;
> +
> +	/* get s5p_platform_mipi_dsim. */
> +	dsim_pd = (struct s5p_platform_mipi_dsim *)dsim->pd;
> +	/* get mipi_dsim_config. */
> +	dsim_config = dsim_pd->dsim_config;
> +	dsim->dsim_config = dsim_config;
> +	dsim->master_ops = &master_ops;
> +
> +	dsim->clock = clk_get(&pdev->dev, "dsim");
> +	if (IS_ERR(dsim->clock)) {
> +		dev_err(&pdev->dev, "failed to get dsim clock source\n");
> +		goto err_clock_get;
> +	}
> +
> +	clk_enable(dsim->clock);
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	if (!res) {
> +		dev_err(&pdev->dev, "failed to get io memory region\n");
> +		ret = -EINVAL;
> +		goto err_platform_get;
> +	}
> +
> +	res = request_mem_region(res->start, resource_size(res),
> +					dev_name(&pdev->dev));
> +	if (!res) {
> +		dev_err(&pdev->dev, "failed to request io memory region\n");
> +		ret = -EINVAL;
> +		goto err_mem_region;
> +	}
> +
> +	dsim->res = res;
> +
> +	dsim->reg_base = ioremap(res->start, resource_size(res));
> +	if (!dsim->reg_base) {
> +		dev_err(&pdev->dev, "failed to remap io region\n");
> +		ret = -EINVAL;
> +		goto err_mem_region;
> +	}
> +
> +	/*
> +	 * it uses frame done interrupt handler
> +	 * only in case of MIPI Video mode.
> +	 */
> +	if (dsim_config->e_interface == DSIM_VIDEO) {
> +		dsim->irq = platform_get_irq(pdev, 0);
> +		if (request_irq(dsim->irq, s5p_mipi_dsi_interrupt_handler,
> +				IRQF_DISABLED, "mipi-dsi", dsim)) {
> +			dev_err(&pdev->dev, "request_irq failed.\n");
> +			goto err_trigger_irq;
> +		}
> +	}
> +
> +	if (dsim->pd->mipi_power)
> +		dsim->pd->mipi_power(dsim, 1);
> +	else {
> +		dev_err(&pdev->dev, "mipi_power is NULL.\n");
> +		goto err_mipi_power;
> +	}
> +
> +	/* find lcd panel driver registered to mipi-dsi driver. */
> +	dsim->dsim_ddi = find_mipi_client_registered(dsim,
> +				dsim_pd->lcd_panel_name);
> +	if (dsim->dsim_config == NULL) {
> +		dev_err(&pdev->dev, "dsim_config is NULL.\n");
> +		goto err_dsim_config;
> +	}
> +
> +	/* set dsim to master of mipi_dsim_lcd_device. */
> +	set_master_to_device(dsim);
> +
> +	s5p_mipi_dsi_init_dsim(dsim);
> +	s5p_mipi_dsi_init_link(dsim);
> +
> +	s5p_mipi_dsi_set_hs_enable(dsim);
> +	/* set cpu command transfer mode to hs. */
> +	s5p_mipi_dsi_set_data_transfer_mode(dsim, 0);
> +
> +	/* initialize mipi-dsi client(lcd panel). */
> +	if (master_to_driver(dsim) && (master_to_driver(dsim))->probe)
> +		(master_to_driver(dsim))->probe(master_to_device(dsim));
> +
> +	/* it needs delay for stabilization */
> +	mdelay(dsim->pd->delay_for_stabilization);
> +
> +	s5p_mipi_dsi_set_display_mode(dsim, dsim->dsim_config);
> +
> +	/* set lcdc data transfer mode to hs. */
> +	s5p_mipi_dsi_set_data_transfer_mode(dsim, 1);
> +
> +	/* in case of command mode, trigger. */
> +	if (dsim->dsim_config->e_interface == DSIM_COMMAND) {
> +		if (dsim_pd->trigger)
> +			dsim_pd->trigger(registered_fb[0]);
> +		else
> +			dev_warn(&pdev->dev, "trigger is null.\n");
> +	}
> +
> +	platform_set_drvdata(pdev, dsim);
> +
> +	dev_info(&pdev->dev, "mipi-dsi driver(%s mode) has been probed.\n",
> +		(dsim_config->e_interface == DSIM_COMMAND) ?
> +			"CPU" : "RGB");
> +
> +	return 0;
> +
> +err_dsim_config:
> +	dsim->pd->mipi_power(dsim, 0);
> +
> +err_mipi_power:
> +err_trigger_irq:
> +	release_resource(dsim->res);
> +	kfree(dsim->res);
> +
> +	iounmap((void __iomem *) dsim->reg_base);
> +
> +err_mem_region:
> +err_platform_get:
> +	clk_disable(dsim->clock);
> +	clk_put(dsim->clock);
> +
> +err_clock_get:
> +	kfree(dsim);
> +
> +	return ret;
> +
> +}
> +
> +static int __devexit s5p_mipi_dsi_remove(struct platform_device *pdev)
> +{
> +	struct mipi_dsim_device *dsim = platform_get_drvdata(pdev);
> +	struct mipi_dsim_ddi *dsim_ddi = NULL;
> +
> +	if (dsim->dsim_config->e_interface == DSIM_VIDEO)
> +		free_irq(dsim->irq, dsim);
> +
> +	iounmap(dsim->reg_base);
> +
> +	clk_disable(dsim->clock);
> +	clk_put(dsim->clock);
> +
> +	release_resource(dsim->res);
> +	kfree(dsim->res);
> +
> +	list_for_each_entry(dsim_ddi, &dsim_ddi_list, list)
> +		kfree(dsim_ddi);
> +
> +	kfree(dsim);
> +
> +	return 0;
> +}
> +
> +#ifdef CONFIG_PM
> +static int s5p_mipi_dsi_suspend(struct platform_device *pdev,
> +		pm_message_t state)
> +{
> +	struct mipi_dsim_device *dsim = platform_get_drvdata(pdev);
> +
> +	dsim->resume_complete = 0;
> +
> +	if (master_to_driver(dsim) && (master_to_driver(dsim))->suspend)
> +		(master_to_driver(dsim))->suspend(master_to_device(dsim));
> +
> +	clk_disable(dsim->clock);
> +
> +	if (dsim->pd->mipi_power)
> +		dsim->pd->mipi_power(dsim, 0);
> +
> +	return 0;
> +}
> +
> +static int s5p_mipi_dsi_resume(struct platform_device *pdev)
> +{
> +	struct mipi_dsim_device *dsim = platform_get_drvdata(pdev);
> +
> +	if (dsim->pd->mipi_power)
> +		dsim->pd->mipi_power(dsim, 1);
> +
> +	clk_enable(dsim->clock);
> +
> +	s5p_mipi_dsi_init_dsim(dsim);
> +	s5p_mipi_dsi_init_link(dsim);
> +
> +	s5p_mipi_dsi_set_hs_enable(dsim);
> +	/* set cpu command transfer mode to hs. */
> +	s5p_mipi_dsi_set_data_transfer_mode(dsim, 0);
> +
> +	/* it needs delay for stabilization */
> +	mdelay(dsim->pd->delay_for_stabilization);
> +
> +	if (master_to_driver(dsim) && (master_to_driver(dsim))->resume)
> +		(master_to_driver(dsim))->resume(master_to_device(dsim));
> +
> +	s5p_mipi_dsi_set_display_mode(dsim, dsim->dsim_config);
> +
> +	/* set lcdc data transfer mode to hs. */
> +	s5p_mipi_dsi_set_data_transfer_mode(dsim, 1);
> +
> +	dsim->resume_complete = 1;
> +
> +	return 0;
> +}
> +#else
> +#define s5p_mipi_dsi_suspend NULL
> +#define s5p_mipi_dsi_resume NULL
> +#endif
> +
> +static struct platform_driver s5p_mipi_dsi_driver = {
> +	.probe = s5p_mipi_dsi_probe,
> +	.remove = __devexit_p(s5p_mipi_dsi_remove),
> +	.suspend = s5p_mipi_dsi_suspend,
> +	.resume = s5p_mipi_dsi_resume,
> +	.driver = {
> +		   .name = "s5p-mipi-dsim",
> +		   .owner = THIS_MODULE,
> +	},
> +};
> +
> +static int s5p_mipi_dsi_register(void)
> +{
> +	platform_driver_register(&s5p_mipi_dsi_driver);
> +
> +	return 0;
> +}
> +
> +static void s5p_mipi_dsi_unregister(void)
> +{
> +	platform_driver_unregister(&s5p_mipi_dsi_driver);
> +}
> +
> +module_init(s5p_mipi_dsi_register);
> +module_exit(s5p_mipi_dsi_unregister);
> +
> +MODULE_AUTHOR("InKi Dae <inki.dae at samsung.com>");
> +MODULE_DESCRIPTION("Samusung MIPI-DSI driver");
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/video/s5p_mipi_dsi_common.c
> b/drivers/video/s5p_mipi_dsi_common.c
> new file mode 100644
> index 0000000..cb5c280
> --- /dev/null
> +++ b/drivers/video/s5p_mipi_dsi_common.c
> @@ -0,0 +1,635 @@
> +/* linux/drivers/video/s5p_mipi_dsi_common.c
> + *
> + * Samsung MIPI-DSI common driver.
> + *
> + * InKi Dae, <inki.dae at samsung.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> +*/
> +
> +#include <linux/module.h>
> +#include <linux/kernel.h>
> +#include <linux/errno.h>
> +#include <linux/mutex.h>
> +#include <linux/wait.h>
> +#include <linux/fs.h>
> +#include <linux/mm.h>
> +#include <linux/fb.h>
> +#include <linux/ctype.h>
> +#include <linux/platform_device.h>
> +#include <linux/io.h>
> +#include <linux/memory.h>
> +#include <linux/delay.h>
> +#include <linux/kthread.h>
> +
> +#include <video/mipi_display.h>
> +
> +#include <plat/fb.h>
> +#include <plat/regs-dsim.h>
> +
> +#include <mach/map.h>
> +#include <plat/dsim.h>
> +#include <plat/regs-dsim.h>
> +
> +#include "s5p_mipi_dsi_lowlevel.h"
> +
> +#define MHZ			(1000 * 1000)
> +#define FIN_HZ			(24 * MHZ)
> +
> +#define DFIN_PLL_MIN_HZ		(6 * MHZ)
> +#define DFIN_PLL_MAX_HZ		(12 * MHZ)
> +
> +#define DFVCO_MIN_HZ		(500 * MHZ)
> +#define DFVCO_MAX_HZ		(1000 * MHZ)
> +
> +#define TRY_GET_FIFO_TIMEOUT	(5000 * 2)
> +
> +#define DSIM_ESCCLK_ON		(0x0)
> +#define DSIM_ESCCLK_OFF		(0x1)
> +
> +/* MIPI-DSIM status types. */
> +enum {
> +	DSIM_STATE_INIT,	/* should be initialized. */
> +	DSIM_STATE_STOP,	/* CPU and LCDC are LP mode. */
> +	DSIM_STATE_HSCLKEN,	/* HS clock was enabled. */
> +	DSIM_STATE_ULPS
> +};
> +
> +/* define DSI lane types. */
> +enum {
> +	DSIM_LANE_CLOCK = (1 << 0),
> +	DSIM_LANE_DATA0 = (1 << 1),
> +	DSIM_LANE_DATA1 = (1 << 2),
> +	DSIM_LANE_DATA2 = (1 << 3),
> +	DSIM_LANE_DATA3 = (1 << 4)
> +};
> +
> +static unsigned int dpll_table[15] = {
> +	100, 120, 170, 220, 270,
> +	320, 390, 450, 510, 560,
> +	640, 690, 770, 870, 950 };
> +
> +static void s5p_mipi_dsi_long_data_wr(struct mipi_dsim_device *dsim,
> +		unsigned int data0, unsigned int data1)
> +{
> +	unsigned int data_cnt = 0, payload = 0;
> +
> +	/* in case that data count is more then 4 */
> +	for (data_cnt = 0; data_cnt < data1; data_cnt += 4) {
> +		/*
> +		 * after sending 4bytes per one time,
> +		 * send remainder data less then 4.
> +		 */
> +		if ((data1 - data_cnt) < 4) {
> +			if ((data1 - data_cnt) == 3) {
> +				payload = *(u8 *)(data0 + data_cnt) |
> +				    (*(u8 *)(data0 + (data_cnt + 1))) << 8 |
> +					(*(u8 *)(data0 + (data_cnt + 2))) <<
16;
> +			dev_dbg(dsim->dev, "count = 3 payload
> = %x, %x %x %x\n",
> +				payload, *(u8 *)(data0 + data_cnt),
> +				*(u8 *)(data0 + (data_cnt + 1)),
> +				*(u8 *)(data0 + (data_cnt + 2)));
> +			} else if ((data1 - data_cnt) == 2) {
> +				payload = *(u8 *)(data0 + data_cnt) |
> +					(*(u8 *)(data0 + (data_cnt + 1))) <<
8;
> +			dev_dbg(dsim->dev,
> +				"count = 2 payload = %x, %x %x\n", payload,
> +				*(u8 *)(data0 + data_cnt),
> +				*(u8 *)(data0 + (data_cnt + 1)));
> +			} else if ((data1 - data_cnt) == 1) {
> +				payload = *(u8 *)(data0 + data_cnt);
> +			}
> +
> +			s5p_mipi_dsi_wr_tx_data(dsim, payload);
> +		/* send 4bytes per one time. */
> +		} else {
> +			payload = *(u8 *)(data0 + data_cnt) |
> +				(*(u8 *)(data0 + (data_cnt + 1))) << 8 |
> +				(*(u8 *)(data0 + (data_cnt + 2))) << 16 |
> +				(*(u8 *)(data0 + (data_cnt + 3))) << 24;
> +
> +			dev_dbg(dsim->dev,
> +				"count = 4 payload = %x, %x %x %x %x\n",
> +				payload, *(u8 *)(data0 + data_cnt),
> +				*(u8 *)(data0 + (data_cnt + 1)),
> +				*(u8 *)(data0 + (data_cnt + 2)),
> +				*(u8 *)(data0 + (data_cnt + 3)));
> +
> +			s5p_mipi_dsi_wr_tx_data(dsim, payload);
> +		}
> +	}
> +}
> +
> +int s5p_mipi_dsi_wr_data(struct mipi_dsim_device *dsim, unsigned int
data_id,
> +	unsigned int data0, unsigned int data1)
> +{
> +	unsigned int timeout = TRY_GET_FIFO_TIMEOUT;
> +	unsigned long delay_val, udelay;
> +	unsigned int check_rx_ack = 0;
> +
> +	if (dsim->state == DSIM_STATE_ULPS) {
> +		dev_err(dsim->dev, "state is ULPS.\n");
> +
> +		return -EINVAL;
> +	}
> +
> +	delay_val = MHZ / dsim->dsim_config->esc_clk;
> +	udelay = 10 * delay_val;
> +
> +	mdelay(udelay);
> +
> +	/* only if transfer mode is LPDT, wait SFR becomes empty. */
> +	if (dsim->state == DSIM_STATE_STOP) {
> +		while (!(s5p_mipi_dsi_get_fifo_state(dsim) &
> +				SFR_HEADER_EMPTY)) {
> +			if ((timeout--) > 0)
> +				mdelay(1);
> +			else {
> +				dev_err(dsim->dev,
> +					"SRF header fifo is not empty.\n");
> +				return -EINVAL;
> +			}
> +		}
> +	}
> +
> +	switch (data_id) {
> +	/* short packet types of packet types for command. */
> +	case MIPI_DSI_GENERIC_SHORT_WRITE_0_PARAM:
> +	case MIPI_DSI_GENERIC_SHORT_WRITE_1_PARAM:
> +	case MIPI_DSI_GENERIC_SHORT_WRITE_2_PARAM:
> +	case MIPI_DSI_DCS_SHORT_WRITE:
> +	case MIPI_DSI_DCS_SHORT_WRITE_PARAM:
> +	case MIPI_DSI_SET_MAXIMUM_RETURN_PACKET_SIZE:
> +		s5p_mipi_dsi_wr_tx_header(dsim, data_id, data0, data1);
> +		if (check_rx_ack)
> +			/* process response func should be implemented */
> +			return 0;
> +		else
> +			return -EINVAL;
> +
> +	/* general command */
> +	case MIPI_DSI_COLOR_MODE_OFF:
> +	case MIPI_DSI_COLOR_MODE_ON:
> +	case MIPI_DSI_SHUTDOWN_PERIPHERAL:
> +	case MIPI_DSI_TURN_ON_PERIPHERAL:
> +		s5p_mipi_dsi_wr_tx_header(dsim, data_id, data0, data1);
> +		if (check_rx_ack)
> +			/* process response func should be implemented. */
> +			return 0;
> +		else
> +			return -EINVAL;
> +
> +	/* packet types for video data */
> +	case MIPI_DSI_V_SYNC_START:
> +	case MIPI_DSI_V_SYNC_END:
> +	case MIPI_DSI_H_SYNC_START:
> +	case MIPI_DSI_H_SYNC_END:
> +	case MIPI_DSI_END_OF_TRANSMISSION:
> +		return 0;
> +
> +	/* short and response packet types for command */
> +	case MIPI_DSI_GENERIC_READ_REQUEST_0_PARAM:
> +	case MIPI_DSI_GENERIC_READ_REQUEST_1_PARAM:
> +	case MIPI_DSI_GENERIC_READ_REQUEST_2_PARAM:
> +	case MIPI_DSI_DCS_READ:
> +		s5p_mipi_dsi_clear_all_interrupt(dsim);
> +		s5p_mipi_dsi_wr_tx_header(dsim, data_id, data0, data1);
> +		/* process response func should be implemented. */
> +		return 0;
> +
> +	/* long packet type and null packet */
> +	case MIPI_DSI_NULL_PACKET:
> +	case MIPI_DSI_BLANKING_PACKET:
> +		return 0;
> +	case MIPI_DSI_GENERIC_LONG_WRITE:
> +	case MIPI_DSI_DCS_LONG_WRITE:
> +	{
> +		unsigned int size, data_cnt = 0, payload = 0;
> +
> +		size = data1 * 4;
> +
> +		/* if data count is less then 4, then send 3bytes data.  */
> +		if (data1 < 4) {
> +			payload = *(u8 *)(data0) |
> +				*(u8 *)(data0 + 1) << 8 |
> +				*(u8 *)(data0 + 2) << 16;
> +
> +			s5p_mipi_dsi_wr_tx_data(dsim, payload);
> +
> +			dev_dbg(dsim->dev, "count = %d payload
> = %x,%x %x %x\n",
> +				data1, payload,
> +				*(u8 *)(data0 + data_cnt),
> +				*(u8 *)(data0 + (data_cnt + 1)),
> +				*(u8 *)(data0 + (data_cnt + 2)));
> +		/* in case that data count is more then 4 */
> +		} else
> +			s5p_mipi_dsi_long_data_wr(dsim, data0, data1);
> +
> +		/* put data into header fifo */
> +		s5p_mipi_dsi_wr_tx_header(dsim, data_id, data1 & 0xff,
> +			(data1 & 0xff00) >> 8);
> +
> +	}
> +	if (check_rx_ack)
> +		/* process response func should be implemented. */
> +		return 0;
> +	else
> +		return -EINVAL;
> +
> +	/* packet typo for video data */
> +	case MIPI_DSI_PACKED_PIXEL_STREAM_16:
> +	case MIPI_DSI_PACKED_PIXEL_STREAM_18:
> +	case MIPI_DSI_PIXEL_STREAM_3BYTE_18:
> +	case MIPI_DSI_PACKED_PIXEL_STREAM_24:
> +		if (check_rx_ack)
> +			/* process response func should be implemented. */
> +			return 0;
> +		else
> +			return -EINVAL;
> +	default:
> +		dev_warn(dsim->dev,
> +			"data id %x is not supported current DSI spec.\n",
> +			data_id);
> +
> +		return -EINVAL;
> +	}
> +
> +	return 0;
> +}
> +
> +int s5p_mipi_dsi_pll_on(struct mipi_dsim_device *dsim, unsigned int
enable)
> +{
> +	int sw_timeout;
> +
> +	if (enable) {
> +		sw_timeout = 1000;
> +
> +		s5p_mipi_dsi_clear_interrupt(dsim);
> +		s5p_mipi_dsi_enable_pll(dsim, 1);
> +		while (1) {
> +			sw_timeout--;
> +			if (s5p_mipi_dsi_is_pll_stable(dsim))
> +				return 0;
> +			if (sw_timeout == 0)
> +				return -EINVAL;
> +		}
> +	} else
> +		s5p_mipi_dsi_enable_pll(dsim, 0);
> +
> +	return 0;
> +}
> +
> +unsigned long s5p_mipi_dsi_change_pll(struct mipi_dsim_device *dsim,
> +	unsigned int pre_divider, unsigned int main_divider,
> +	unsigned int scaler)
> +{
> +	unsigned long dfin_pll, dfvco, dpll_out;
> +	unsigned int i, freq_band = 0xf;
> +
> +	dfin_pll = (FIN_HZ / pre_divider);
> +
> +	if (dfin_pll < DFIN_PLL_MIN_HZ || dfin_pll > DFIN_PLL_MAX_HZ) {
> +		dev_warn(dsim->dev, "fin_pll range should be 6MHz ~
12MHz\n");
> +		s5p_mipi_dsi_enable_afc(dsim, 0, 0);
> +	} else {
> +		if (dfin_pll < 7 * MHZ)
> +			s5p_mipi_dsi_enable_afc(dsim, 1, 0x1);
> +		else if (dfin_pll < 8 * MHZ)
> +			s5p_mipi_dsi_enable_afc(dsim, 1, 0x0);
> +		else if (dfin_pll < 9 * MHZ)
> +			s5p_mipi_dsi_enable_afc(dsim, 1, 0x3);
> +		else if (dfin_pll < 10 * MHZ)
> +			s5p_mipi_dsi_enable_afc(dsim, 1, 0x2);
> +		else if (dfin_pll < 11 * MHZ)
> +			s5p_mipi_dsi_enable_afc(dsim, 1, 0x5);
> +		else
> +			s5p_mipi_dsi_enable_afc(dsim, 1, 0x4);
> +	}
> +
> +	dfvco = dfin_pll * main_divider;
> +	dev_dbg(dsim->dev, "dfvco = %lu, dfin_pll = %lu, main_divider =
%d\n",
> +				dfvco, dfin_pll, main_divider);
> +	if (dfvco < DFVCO_MIN_HZ || dfvco > DFVCO_MAX_HZ)
> +		dev_warn(dsim->dev, "fvco range should be 500MHz ~
1000MHz\n");
> +
> +	dpll_out = dfvco / (1 << scaler);
> +	dev_dbg(dsim->dev, "dpll_out = %lu, dfvco = %lu, scaler = %d\n",
> +		dpll_out, dfvco, scaler);
> +
> +	for (i = 0; i < ARRAY_SIZE(dpll_table); i++) {
> +		if (dpll_out < dpll_table[i] * MHZ) {
> +			freq_band = i;
> +			break;
> +		}
> +	}
> +
> +	dev_dbg(dsim->dev, "freq_band = %d\n", freq_band);
> +
> +	s5p_mipi_dsi_pll_freq(dsim, pre_divider, main_divider, scaler);
> +
> +	s5p_mipi_dsi_hs_zero_ctrl(dsim, 0);
> +	s5p_mipi_dsi_prep_ctrl(dsim, 0);
> +
> +	/* Freq Band */
> +	s5p_mipi_dsi_pll_freq_band(dsim, freq_band);
> +
> +	/* Stable time */
> +	s5p_mipi_dsi_pll_stable_time(dsim,
dsim->dsim_config->pll_stable_time);
> +
> +	/* Enable PLL */
> +	dev_dbg(dsim->dev, "FOUT of mipi dphy pll is %luMHz\n",
> +		(dpll_out / MHZ));
> +
> +	return dpll_out;
> +}
> +
> +int s5p_mipi_dsi_set_clock(struct mipi_dsim_device *dsim,
> +	unsigned int byte_clk_sel, unsigned int enable)
> +{
> +	unsigned int esc_div;
> +	unsigned long esc_clk_error_rate;
> +
> +	if (enable) {
> +		dsim->e_clk_src = byte_clk_sel;
> +
> +		/* Escape mode clock and byte clock source */
> +		s5p_mipi_dsi_set_byte_clock_src(dsim, byte_clk_sel);
> +
> +		/* DPHY, DSIM Link : D-PHY clock out */
> +		if (byte_clk_sel == DSIM_PLL_OUT_DIV8) {
> +			dsim->hs_clk = s5p_mipi_dsi_change_pll(dsim,
> +				dsim->dsim_config->p, dsim->dsim_config->m,
> +				dsim->dsim_config->s);
> +			if (dsim->hs_clk == 0) {
> +				dev_err(dsim->dev,
> +					"failed to get hs clock.\n");
> +				return -EINVAL;
> +			}
> +
> +			dsim->byte_clk = dsim->hs_clk / 8;
> +			s5p_mipi_dsi_enable_pll_bypass(dsim, 0);
> +			s5p_mipi_dsi_pll_on(dsim, 1);
> +		/* DPHY : D-PHY clock out, DSIM link : external clock out */
> +		} else if (byte_clk_sel == DSIM_EXT_CLK_DIV8)
> +			dev_warn(dsim->dev,
> +				"this project is not support \
> +				external clock source for MIPI DSIM\n");
> +		else if (byte_clk_sel == DSIM_EXT_CLK_BYPASS)
> +			dev_warn(dsim->dev,
> +				"this project is not support \
> +				external clock source for MIPI DSIM\n");
> +
> +		/* escape clock divider */
> +		esc_div = dsim->byte_clk / (dsim->dsim_config->esc_clk);
> +		dev_dbg(dsim->dev,
> +			"esc_div = %d, byte_clk = %lu, esc_clk = %lu\n",
> +			esc_div, dsim->byte_clk,
dsim->dsim_config->esc_clk);
> +		if ((dsim->byte_clk / esc_div) >= (20 * MHZ) ||
> +				(dsim->byte_clk / esc_div) >
> +					dsim->dsim_config->esc_clk)
> +			esc_div += 1;
> +
> +		dsim->escape_clk = dsim->byte_clk / esc_div;
> +		dev_dbg(dsim->dev,
> +			"escape_clk = %lu, byte_clk = %lu, esc_div = %d\n",
> +			dsim->escape_clk, dsim->byte_clk, esc_div);
> +
> +		/* enable escape clock. */
> +		s5p_mipi_dsi_enable_byte_clock(dsim, DSIM_ESCCLK_ON);
> +
> +		/* enable byte clk and escape clock */
> +		s5p_mipi_dsi_set_esc_clk_prs(dsim, 1, esc_div);
> +		/* escape clock on lane */
> +		s5p_mipi_dsi_enable_esc_clk_on_lane(dsim,
> +			(DSIM_LANE_CLOCK | dsim->data_lane), 1);
> +
> +		dev_dbg(dsim->dev, "byte clock is %luMHz\n",
> +			(dsim->byte_clk / MHZ));
> +		dev_dbg(dsim->dev, "escape clock that user's need is %lu\n",
> +			(dsim->dsim_config->esc_clk / MHZ));
> +		dev_dbg(dsim->dev, "escape clock divider is %x\n", esc_div);
> +		dev_dbg(dsim->dev, "escape clock is %luMHz\n",
> +			((dsim->byte_clk / esc_div) / MHZ));
> +
> +		if ((dsim->byte_clk / esc_div) > dsim->escape_clk) {
> +			esc_clk_error_rate = dsim->escape_clk /
> +				(dsim->byte_clk / esc_div);
> +			dev_warn(dsim->dev, "error rate is %lu over.\n",
> +				(esc_clk_error_rate / 100));
> +		} else if ((dsim->byte_clk / esc_div) < (dsim->escape_clk))
{
> +			esc_clk_error_rate = (dsim->byte_clk / esc_div) /
> +				dsim->escape_clk;
> +			dev_warn(dsim->dev, "error rate is %lu under.\n",
> +				(esc_clk_error_rate / 100));
> +		}
> +	} else {
> +		s5p_mipi_dsi_enable_esc_clk_on_lane(dsim,
> +			(DSIM_LANE_CLOCK | dsim->data_lane), 0);
> +		s5p_mipi_dsi_set_esc_clk_prs(dsim, 0, 0);
> +
> +		/* disable escape clock. */
> +		s5p_mipi_dsi_enable_byte_clock(dsim, DSIM_ESCCLK_OFF);
> +
> +		if (byte_clk_sel == DSIM_PLL_OUT_DIV8)
> +			s5p_mipi_dsi_pll_on(dsim, 0);
> +	}
> +
> +	return 0;
> +}
> +
> +int s5p_mipi_dsi_init_dsim(struct mipi_dsim_device *dsim)
> +{
> +	if (dsim->pd->init_d_phy)
> +		dsim->pd->init_d_phy(dsim);
> +
> +	dsim->state = DSIM_STATE_INIT;
> +
> +	switch (dsim->dsim_config->e_no_data_lane) {
> +	case DSIM_DATA_LANE_1:
> +		dsim->data_lane = DSIM_LANE_DATA0;
> +		break;
> +	case DSIM_DATA_LANE_2:
> +		dsim->data_lane = DSIM_LANE_DATA0 | DSIM_LANE_DATA1;
> +		break;
> +	case DSIM_DATA_LANE_3:
> +		dsim->data_lane = DSIM_LANE_DATA0 | DSIM_LANE_DATA1 |
> +			DSIM_LANE_DATA2;
> +		break;
> +	case DSIM_DATA_LANE_4:
> +		dsim->data_lane = DSIM_LANE_DATA0 | DSIM_LANE_DATA1 |
> +			DSIM_LANE_DATA2 | DSIM_LANE_DATA3;
> +		break;
> +	default:
> +		dev_info(dsim->dev, "data lane is invalid.\n");
> +		return -EINVAL;
> +	};
> +
> +	s5p_mipi_dsi_sw_reset(dsim);
> +	s5p_mipi_dsi_dp_dn_swap(dsim, 0);
> +
> +	return 0;
> +}
> +
> +int s5p_mipi_dsi_enable_frame_done_int(struct mipi_dsim_device *dsim,
> +	unsigned int enable)
> +{
> +	/* enable only frame done interrupt */
> +	s5p_mipi_dsi_set_interrupt_mask(dsim, INTMSK_FRAME_DONE, enable);
> +
> +	return 0;
> +}
> +
> +int s5p_mipi_dsi_set_display_mode(struct mipi_dsim_device *dsim,
> +	struct mipi_dsim_config *dsim_config)
> +{
> +	struct fb_videomode *lcd_video = NULL;
> +	struct s3c_fb_pd_win *pd;
> +	unsigned int width = 0, height = 0;
> +
> +	pd = (struct s3c_fb_pd_win *)dsim->dsim_config->lcd_panel_info;
> +	lcd_video = (struct fb_videomode *)&pd->win_mode;
> +
> +	width = lcd_video->xres;
> +	height = lcd_video->yres;
> +
> +	/* in case of VIDEO MODE (RGB INTERFACE) */
> +	if (dsim->dsim_config->e_interface == (u32) DSIM_VIDEO) {
> +		if (dsim->dsim_config->auto_vertical_cnt == 0) {
> +			s5p_mipi_dsi_set_main_disp_vporch(dsim,
> +				lcd_video->upper_margin,
> +				lcd_video->lower_margin, 0);
> +			s5p_mipi_dsi_set_main_disp_hporch(dsim,
> +				lcd_video->left_margin,
> +				lcd_video->right_margin);
> +			s5p_mipi_dsi_set_main_disp_sync_area(dsim,
> +				lcd_video->vsync_len,
> +				lcd_video->hsync_len);
> +		}
> +	}
> +
> +	s5p_mipi_dsi_set_main_disp_resol(dsim, height, width);
> +
> +	s5p_mipi_dsi_display_config(dsim, dsim->dsim_config);
> +
> +	return 0;
> +}
> +
> +int s5p_mipi_dsi_init_link(struct mipi_dsim_device *dsim)
> +{
> +	unsigned int time_out = 100;
> +
> +	switch (dsim->state) {
> +	case DSIM_STATE_INIT:
> +		s5p_mipi_dsi_sw_reset(dsim);
> +
> +		s5p_mipi_dsi_init_fifo_pointer(dsim, 0x1f);
> +
> +		/* dsi configuration */
> +		s5p_mipi_dsi_init_config(dsim);
> +		s5p_mipi_dsi_enable_lane(dsim, DSIM_LANE_CLOCK, 1);
> +		s5p_mipi_dsi_enable_lane(dsim, dsim->data_lane, 1);
> +
> +		/* set clock configuration */
> +		s5p_mipi_dsi_set_clock(dsim, dsim->dsim_config->e_byte_clk,
1);
> +
> +		/* check clock and data lane state are stop state */
> +		while (!(s5p_mipi_dsi_is_lane_state(dsim))) {
> +			time_out--;
> +			if (time_out == 0) {
> +				dev_err(dsim->dev,
> +					"DSI Master is not stop state.\n");
> +				dev_err(dsim->dev,
> +					"Check initialization process\n");
> +
> +				return -EINVAL;
> +			}
> +		}
> +
> +		if (time_out != 0) {
> +			dev_info(dsim->dev,
> +				"DSI Master driver has been completed.\n");
> +			dev_info(dsim->dev, "DSI Master state is stop
> state\n");
> +		}
> +
> +		dsim->state = DSIM_STATE_STOP;
> +
> +		/* BTA sequence counters */
> +		s5p_mipi_dsi_set_stop_state_counter(dsim,
> +			dsim->dsim_config->stop_holding_cnt);
> +		s5p_mipi_dsi_set_bta_timeout(dsim,
> +			dsim->dsim_config->bta_timeout);
> +		s5p_mipi_dsi_set_lpdr_timeout(dsim,
> +			dsim->dsim_config->rx_timeout);
> +
> +		return 0;
> +	default:
> +		dev_info(dsim->dev, "DSI Master is already init.\n");
> +		return 0;
> +	}
> +
> +	return 0;
> +}
> +
> +int s5p_mipi_dsi_set_hs_enable(struct mipi_dsim_device *dsim)
> +{
> +	if (dsim->state == DSIM_STATE_STOP) {
> +		if (dsim->e_clk_src != DSIM_EXT_CLK_BYPASS) {
> +			dsim->state = DSIM_STATE_HSCLKEN;
> +
> +			 /* set LCDC and CPU transfer mode to HS. */
> +			s5p_mipi_dsi_set_lcdc_transfer_mode(dsim, 0);
> +			s5p_mipi_dsi_set_cpu_transfer_mode(dsim, 0);
> +
> +			s5p_mipi_dsi_enable_hs_clock(dsim, 1);
> +
> +			return 0;
> +		} else
> +			dev_warn(dsim->dev,
> +				"clock source is external bypass.\n");
> +	} else
> +		dev_warn(dsim->dev, "DSIM is not stop state.\n");
> +
> +	return 0;
> +}
> +
> +int s5p_mipi_dsi_set_data_transfer_mode(struct mipi_dsim_device *dsim,
> +		unsigned int mode)
> +{
> +	if (mode) {
> +		if (dsim->state != DSIM_STATE_HSCLKEN) {
> +			dev_err(dsim->dev, "HS Clock lane is not
enabled.\n");
> +			return -EINVAL;
> +		}
> +
> +		s5p_mipi_dsi_set_lcdc_transfer_mode(dsim, 0);
> +	} else {
> +		if (dsim->state == DSIM_STATE_INIT || dsim->state ==
> +			DSIM_STATE_ULPS) {
> +			dev_err(dsim->dev,
> +				"DSI Master is not STOP or HSDT state.\n");
> +			return -EINVAL;
> +		}
> +
> +		s5p_mipi_dsi_set_cpu_transfer_mode(dsim, 0);
> +	}
> +
> +	return 0;
> +}
> +
> +int s5p_mipi_dsi_get_frame_done_status(struct mipi_dsim_device *dsim)
> +{
> +	return _s5p_mipi_dsi_get_frame_done_status(dsim);
> +}
> +
> +int s5p_mipi_dsi_clear_frame_done(struct mipi_dsim_device *dsim)
> +{
> +	_s5p_mipi_dsi_clear_frame_done(dsim);
> +
> +	return 0;
> +}
> +
> +MODULE_AUTHOR("InKi Dae <inki.dae at samsung.com>");
> +MODULE_DESCRIPTION("Samusung MIPI-DSIM common driver");
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/video/s5p_mipi_dsi_common.h
> b/drivers/video/s5p_mipi_dsi_common.h
> new file mode 100644
> index 0000000..040d70e
> --- /dev/null
> +++ b/drivers/video/s5p_mipi_dsi_common.h
> @@ -0,0 +1,38 @@
> +/* linux/drivers/video/s5p_mipi_dsi_common.h
> + *
> + * Header file for Samsung MIPI-DSI common driver.
> + *
> + * Copyright (c) 2009 Samsung Electronics
> + * InKi Dae <inki.dae at samsung.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> +*/
> +
> +#ifndef _S5P_MIPI_DSI_COMMON_H
> +#define _S5P_MIPI_DSI_COMMON_H
> +
> +int s5p_mipi_dsi_wr_data(struct mipi_dsim_device *dsim, unsigned int
data_id,
> +	unsigned int data0, unsigned int data1);
> +int s5p_mipi_dsi_pll_on(struct mipi_dsim_device *dsim, unsigned int
enable);
> +unsigned long s5p_mipi_dsi_change_pll(struct mipi_dsim_device *dsim,
> +	unsigned int pre_divider, unsigned int main_divider,
> +	unsigned int scaler);
> +int s5p_mipi_dsi_set_clock(struct mipi_dsim_device *dsim,
> +	unsigned int byte_clk_sel, unsigned int enable);
> +int s5p_mipi_dsi_init_dsim(struct mipi_dsim_device *dsim);
> +int s5p_mipi_dsi_set_display_mode(struct mipi_dsim_device *dsim,
> +			struct mipi_dsim_config *dsim_info);
> +int s5p_mipi_dsi_init_link(struct mipi_dsim_device *dsim);
> +int s5p_mipi_dsi_set_hs_enable(struct mipi_dsim_device *dsim);
> +int s5p_mipi_dsi_set_data_transfer_mode(struct mipi_dsim_device *dsim,
> +		unsigned int mode);
> +int s5p_mipi_dsi_enable_frame_done_int(struct mipi_dsim_device *dsim,
> +	unsigned int enable);
> +int s5p_mipi_dsi_get_frame_done_status(struct mipi_dsim_device *dsim);
> +int s5p_mipi_dsi_clear_frame_done(struct mipi_dsim_device *dsim);
> +
> +extern struct fb_info *registered_fb[FB_MAX] __read_mostly;
> +
> +#endif /* _S5P_MIPI_DSI_COMMON_H */
> diff --git a/drivers/video/s5p_mipi_dsi_lowlevel.c
> b/drivers/video/s5p_mipi_dsi_lowlevel.c
> new file mode 100644
> index 0000000..8afea36
> --- /dev/null
> +++ b/drivers/video/s5p_mipi_dsi_lowlevel.c
> @@ -0,0 +1,553 @@
> +/* linux/drivers/video/s5p_mipi_dsi_lowlevel.c
> + *
> + * Samsung MIPI-DSI lowlevel driver.
> + *
> + * InKi Dae, <inki.dae at samsung.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> +*/
> +
> +#include <linux/module.h>
> +#include <linux/kernel.h>
> +#include <linux/errno.h>
> +#include <linux/mutex.h>
> +#include <linux/wait.h>
> +#include <linux/delay.h>
> +#include <linux/fs.h>
> +#include <linux/mm.h>
> +#include <linux/ctype.h>
> +#include <linux/io.h>
> +
> +#include <mach/map.h>
> +
> +#include <plat/dsim.h>
> +#include <plat/regs-dsim.h>
> +
> +void s5p_mipi_dsi_func_reset(struct mipi_dsim_device *dsim)
> +{
> +	unsigned int reg;
> +
> +	reg = readl(dsim->reg_base + S5P_DSIM_SWRST);
> +
> +	reg |= DSIM_FUNCRST;
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_SWRST);
> +}
> +
> +void s5p_mipi_dsi_sw_reset(struct mipi_dsim_device *dsim)
> +{
> +	unsigned int reg;
> +
> +	reg = readl(dsim->reg_base + S5P_DSIM_SWRST);
> +
> +	reg |= DSIM_SWRST;
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_SWRST);
> +}
> +
> +void s5p_mipi_dsi_set_interrupt_mask(struct mipi_dsim_device *dsim,
> +		unsigned int mode, unsigned int mask)
> +{
> +	unsigned int reg = readl(dsim->reg_base + S5P_DSIM_INTMSK);
> +
> +	if (mask)
> +		reg |= mode;
> +	else
> +		reg &= ~mode;
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_INTMSK);
> +}
> +
> +void s5p_mipi_dsi_init_fifo_pointer(struct mipi_dsim_device *dsim,
> +		unsigned int cfg)
> +{
> +	unsigned int reg;
> +
> +	reg = readl(dsim->reg_base + S5P_DSIM_FIFOCTRL);
> +
> +	writel(reg & ~(cfg), dsim->reg_base + S5P_DSIM_FIFOCTRL);
> +	mdelay(10);
> +	reg |= cfg;
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_FIFOCTRL);
> +}
> +
> +/*
> + * this function set PLL P, M and S value in D-PHY
> + */
> +void s5p_mipi_dsi_set_phy_tunning(struct mipi_dsim_device *dsim,
> +		unsigned int value)
> +{
> +	writel(DSIM_AFC_CTL(value), dsim->reg_base + S5P_DSIM_PHYACCHR);
> +}
> +
> +void s5p_mipi_dsi_set_main_disp_resol(struct mipi_dsim_device *dsim,
> +	unsigned int vert_resol, unsigned int hori_resol)
> +{
> +	unsigned int reg;
> +
> +	/* standby should be set after configuration so set to not ready*/
> +	reg = (readl(dsim->reg_base + S5P_DSIM_MDRESOL)) &
> +		~(DSIM_MAIN_STAND_BY);
> +	writel(reg, dsim->reg_base + S5P_DSIM_MDRESOL);
> +
> +	reg &= ~(0x7ff << 16) & ~(0x7ff << 0);
> +	reg |= DSIM_MAIN_VRESOL(vert_resol) | DSIM_MAIN_HRESOL(hori_resol);
> +
> +	reg |= DSIM_MAIN_STAND_BY;
> +	writel(reg, dsim->reg_base + S5P_DSIM_MDRESOL);
> +}
> +
> +void s5p_mipi_dsi_set_main_disp_vporch(struct mipi_dsim_device *dsim,
> +	unsigned int cmd_allow, unsigned int vfront, unsigned int vback)
> +{
> +	unsigned int reg;
> +
> +	reg = (readl(dsim->reg_base + S5P_DSIM_MVPORCH)) &
> +		~(DSIM_CMD_ALLOW_MASK) & ~(DSIM_STABLE_VFP_MASK) &
> +		~(DSIM_MAIN_VBP_MASK);
> +
> +	reg |= ((cmd_allow & 0xf) << DSIM_CMD_ALLOW_SHIFT) |
> +		((vfront & 0x7ff) << DSIM_STABLE_VFP_SHIFT) |
> +		((vback & 0x7ff) << DSIM_MAIN_VBP_SHIFT);
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_MVPORCH);
> +}
> +
> +void s5p_mipi_dsi_set_main_disp_hporch(struct mipi_dsim_device *dsim,
> +	unsigned int front, unsigned int back)
> +{
> +	unsigned int reg;
> +
> +	reg = (readl(dsim->reg_base + S5P_DSIM_MHPORCH)) &
> +		~(DSIM_MAIN_HFP_MASK) & ~(DSIM_MAIN_HBP_MASK);
> +
> +	reg |= (front << DSIM_MAIN_HFP_SHIFT) | (back <<
DSIM_MAIN_HBP_SHIFT);
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_MHPORCH);
> +}
> +
> +void s5p_mipi_dsi_set_main_disp_sync_area(struct mipi_dsim_device *dsim,
> +	unsigned int vert, unsigned int hori)
> +{
> +	unsigned int reg;
> +
> +	reg = (readl(dsim->reg_base + S5P_DSIM_MSYNC)) &
> +		~(DSIM_MAIN_VSA_MASK) & ~(DSIM_MAIN_HSA_MASK);
> +
> +	reg |= ((vert & 0x3ff) << DSIM_MAIN_VSA_SHIFT) |
> +		(hori << DSIM_MAIN_HSA_SHIFT);
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_MSYNC);
> +}
> +
> +void s5p_mipi_dsi_set_sub_disp_resol(struct mipi_dsim_device *dsim,
> +	unsigned int vert, unsigned int hori)
> +{
> +	unsigned int reg;
> +
> +	reg = (readl(dsim->reg_base + S5P_DSIM_SDRESOL)) &
> +		~(DSIM_SUB_STANDY_MASK);
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_SDRESOL);
> +
> +	reg &= ~(DSIM_SUB_VRESOL_MASK) | ~(DSIM_SUB_HRESOL_MASK);
> +	reg |= ((vert & 0x7ff) << DSIM_SUB_VRESOL_SHIFT) |
> +		((hori & 0x7ff) << DSIM_SUB_HRESOL_SHIFT);
> +	writel(reg, dsim->reg_base + S5P_DSIM_SDRESOL);
> +
> +	reg |= (1 << DSIM_SUB_STANDY_SHIFT);
> +	writel(reg, dsim->reg_base + S5P_DSIM_SDRESOL);
> +}
> +
> +void s5p_mipi_dsi_init_config(struct mipi_dsim_device *dsim)
> +{
> +	struct mipi_dsim_config *dsim_config = dsim->dsim_config;
> +
> +	unsigned int cfg = (readl(dsim->reg_base + S5P_DSIM_CONFIG)) &
> +		~(1 << 28) & ~(0x1f << 20) & ~(0x3 << 5);
> +
> +	cfg =	(dsim_config->auto_flush << 29) |
> +		(dsim_config->eot_disable << 28) |
> +		(dsim_config->auto_vertical_cnt << DSIM_AUTO_MODE_SHIFT) |
> +		(dsim_config->hse << DSIM_HSE_MODE_SHIFT) |
> +		(dsim_config->hfp << DSIM_HFP_MODE_SHIFT) |
> +		(dsim_config->hbp << DSIM_HBP_MODE_SHIFT) |
> +		(dsim_config->hsa << DSIM_HSA_MODE_SHIFT) |
> +		(dsim_config->e_no_data_lane << DSIM_NUM_OF_DATALANE_SHIFT);
> +
> +	writel(cfg, dsim->reg_base + S5P_DSIM_CONFIG);
> +}
> +
> +void s5p_mipi_dsi_display_config(struct mipi_dsim_device *dsim,
> +				struct mipi_dsim_config *dsim_config)
> +{
> +	u32 reg = (readl(dsim->reg_base + S5P_DSIM_CONFIG)) &
> +		~(0x3 << 26) & ~(1 << 25) & ~(0x3 << 18) & ~(0x7 << 12) &
> +		~(0x3 << 16) & ~(0x7 << 8);
> +
> +	if (dsim_config->e_interface == DSIM_VIDEO)
> +		reg |= (1 << 25);
> +	else if (dsim_config->e_interface == DSIM_COMMAND)
> +		reg &= ~(1 << 25);
> +	else {
> +		dev_err(dsim->dev, "this ddi is not MIPI interface.\n");
> +		return;
> +	}
> +
> +	/* main lcd */
> +	reg |= ((u8) (dsim_config->e_burst_mode) & 0x3) << 26 |
> +		((u8) (dsim_config->e_virtual_ch) & 0x3) << 18 |
> +		((u8) (dsim_config->e_pixel_format) & 0x7) << 12;
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_CONFIG);
> +}
> +
> +void s5p_mipi_dsi_enable_lane(struct mipi_dsim_device *dsim, unsigned int
> lane,
> +	unsigned int enable)
> +{
> +	unsigned int reg;
> +
> +	reg = readl(dsim->reg_base + S5P_DSIM_CONFIG);
> +
> +	if (enable)
> +		reg |= DSIM_LANE_ENx(lane);
> +	else
> +		reg &= ~DSIM_LANE_ENx(lane);
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_CONFIG);
> +}
> +
> +
> +void s5p_mipi_dsi_set_data_lane_number(struct mipi_dsim_device *dsim,
> +	unsigned int count)
> +{
> +	unsigned int cfg;
> +
> +	/* get the data lane number. */
> +	cfg = DSIM_NUM_OF_DATA_LANE(count);
> +
> +	writel(cfg, dsim->reg_base + S5P_DSIM_CONFIG);
> +}
> +
> +void s5p_mipi_dsi_enable_afc(struct mipi_dsim_device *dsim, unsigned int
> enable,
> +	unsigned int afc_code)
> +{
> +	unsigned int reg = readl(dsim->reg_base + S5P_DSIM_PHYACCHR);
> +
> +	if (enable) {
> +		reg |= (1 << 14);
> +		reg &= ~(0x7 << 5);
> +		reg |= (afc_code & 0x7) << 5;
> +	} else
> +		reg &= ~(1 << 14);
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_PHYACCHR);
> +}
> +
> +void s5p_mipi_dsi_enable_pll_bypass(struct mipi_dsim_device *dsim,
> +	unsigned int enable)
> +{
> +	unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_CLKCTRL)) &
> +		~(DSIM_PLL_BYPASS_EXTERNAL);
> +
> +	reg |= enable << DSIM_PLL_BYPASS_SHIFT;
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_CLKCTRL);
> +}
> +
> +void s5p_mipi_dsi_set_pll_pms(struct mipi_dsim_device *dsim, unsigned int
p,
> +	unsigned int m, unsigned int s)
> +{
> +	unsigned int reg = readl(dsim->reg_base + S5P_DSIM_PLLCTRL);
> +
> +	reg |= ((p & 0x3f) << 13) | ((m & 0x1ff) << 4) | ((s & 0x7) << 1);
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_PLLCTRL);
> +}
> +
> +void s5p_mipi_dsi_pll_freq_band(struct mipi_dsim_device *dsim,
> +		unsigned int freq_band)
> +{
> +	unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_PLLCTRL)) &
> +		~(0x1f << DSIM_FREQ_BAND_SHIFT);
> +
> +	reg |= ((freq_band & 0x1f) << DSIM_FREQ_BAND_SHIFT);
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_PLLCTRL);
> +}
> +
> +void s5p_mipi_dsi_pll_freq(struct mipi_dsim_device *dsim,
> +		unsigned int pre_divider, unsigned int main_divider,
> +		unsigned int scaler)
> +{
> +	unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_PLLCTRL)) &
> +		~(0x7ffff << 1);
> +
> +	reg |= (pre_divider & 0x3f) << 13 | (main_divider & 0x1ff) << 4 |
> +		(scaler & 0x7) << 1;
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_PLLCTRL);
> +}
> +
> +void s5p_mipi_dsi_pll_stable_time(struct mipi_dsim_device *dsim,
> +	unsigned int lock_time)
> +{
> +	writel(lock_time, dsim->reg_base + S5P_DSIM_PLLTMR);
> +}
> +
> +void s5p_mipi_dsi_enable_pll(struct mipi_dsim_device *dsim, unsigned int
> enable)
> +{
> +	unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_PLLCTRL)) &
> +		~(0x1 << DSIM_PLL_EN_SHIFT);
> +
> +	reg |= ((enable & 0x1) << DSIM_PLL_EN_SHIFT);
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_PLLCTRL);
> +}
> +
> +void s5p_mipi_dsi_set_byte_clock_src(struct mipi_dsim_device *dsim,
> +		unsigned int src)
> +{
> +	unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_CLKCTRL)) &
> +		~(0x3 << DSIM_BYTE_CLK_SRC_SHIFT);
> +
> +	reg |= ((unsigned int) src) << DSIM_BYTE_CLK_SRC_SHIFT;
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_CLKCTRL);
> +}
> +
> +void s5p_mipi_dsi_enable_byte_clock(struct mipi_dsim_device *dsim,
> +		unsigned int enable)
> +{
> +	unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_CLKCTRL)) &
> +		~(1 << DSIM_BYTE_CLKEN_SHIFT);
> +
> +	reg |= enable << DSIM_BYTE_CLKEN_SHIFT;
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_CLKCTRL);
> +}
> +
> +void s5p_mipi_dsi_set_esc_clk_prs(struct mipi_dsim_device *dsim,
> +		unsigned int enable, unsigned int prs_val)
> +{
> +	unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_CLKCTRL)) &
> +		~(1 << DSIM_ESC_CLKEN_SHIFT) & ~(0xffff);
> +
> +	reg |= enable << DSIM_ESC_CLKEN_SHIFT;
> +	if (enable)
> +		reg |= prs_val;
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_CLKCTRL);
> +}
> +
> +void s5p_mipi_dsi_enable_esc_clk_on_lane(struct mipi_dsim_device *dsim,
> +		unsigned int lane_sel, unsigned int enable)
> +{
> +	unsigned int reg = readl(dsim->reg_base + S5P_DSIM_CLKCTRL);
> +
> +	if (enable)
> +		reg |= DSIM_LANE_ESC_CLKEN(lane_sel);
> +	else
> +
> +		reg &= ~DSIM_LANE_ESC_CLKEN(lane_sel);
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_CLKCTRL);
> +}
> +
> +void s5p_mipi_dsi_force_dphy_stop_state(struct mipi_dsim_device *dsim,
> +	unsigned int enable)
> +{
> +	unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_ESCMODE)) &
> +		~(0x1 << DSIM_FORCE_STOP_STATE_SHIFT);
> +
> +	reg |= ((enable & 0x1) << DSIM_FORCE_STOP_STATE_SHIFT);
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_ESCMODE);
> +}
> +
> +unsigned int s5p_mipi_dsi_is_lane_state(struct mipi_dsim_device *dsim)
> +{
> +	unsigned int reg = readl(dsim->reg_base + S5P_DSIM_STATUS);
> +
> +	/**
> +	 * check clock and data lane states.
> +	 * if MIPI-DSI controller was enabled at bootloader then
> +	 * TX_READY_HS_CLK is enabled otherwise STOP_STATE_CLK.
> +	 * so it should be checked for two case.
> +	 */
> +	if ((reg & DSIM_STOP_STATE_DAT(0xf)) &&
> +			((reg & DSIM_STOP_STATE_CLK) ||
> +			 (reg & DSIM_TX_READY_HS_CLK)))
> +		return 1;
> +	else
> +		return 0;
> +
> +	return 0;
> +}
> +
> +void s5p_mipi_dsi_set_stop_state_counter(struct mipi_dsim_device *dsim,
> +		unsigned int cnt_val)
> +{
> +	unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_ESCMODE)) &
> +		~(0x7ff << DSIM_STOP_STATE_CNT_SHIFT);
> +
> +	reg |= ((cnt_val & 0x7ff) << DSIM_STOP_STATE_CNT_SHIFT);
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_ESCMODE);
> +}
> +
> +void s5p_mipi_dsi_set_bta_timeout(struct mipi_dsim_device *dsim,
> +		unsigned int timeout)
> +{
> +	unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_TIMEOUT)) &
> +		~(0xff << DSIM_BTA_TOUT_SHIFT);
> +
> +	reg |= (timeout << DSIM_BTA_TOUT_SHIFT);
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_TIMEOUT);
> +}
> +
> +void s5p_mipi_dsi_set_lpdr_timeout(struct mipi_dsim_device *dsim,
> +		unsigned int timeout)
> +{
> +	unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_TIMEOUT)) &
> +		~(0xffff << DSIM_LPDR_TOUT_SHIFT);
> +
> +	reg |= (timeout << DSIM_LPDR_TOUT_SHIFT);
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_TIMEOUT);
> +}
> +
> +void s5p_mipi_dsi_set_cpu_transfer_mode(struct mipi_dsim_device *dsim,
> +		unsigned int lp)
> +{
> +	unsigned int reg = readl(dsim->reg_base + S5P_DSIM_ESCMODE);
> +
> +	reg &= ~DSIM_CMD_LPDT_LP;
> +
> +	reg |= lp << DSIM_CMD_LPDT_SHIFT;
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_ESCMODE);
> +}
> +
> +void s5p_mipi_dsi_set_lcdc_transfer_mode(struct mipi_dsim_device *dsim,
> +		unsigned int lp)
> +{
> +	unsigned int reg = readl(dsim->reg_base + S5P_DSIM_ESCMODE);
> +
> +	reg &= ~DSIM_TX_LPDT_LP;
> +
> +	reg |= lp << DSIM_TX_LPDT_SHIFT;
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_ESCMODE);
> +}
> +
> +void s5p_mipi_dsi_enable_hs_clock(struct mipi_dsim_device *dsim,
> +		unsigned int enable)
> +{
> +	unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_CLKCTRL)) &
> +		~(1 << DSIM_TX_REQUEST_HSCLK_SHIFT);
> +
> +	reg |= enable << DSIM_TX_REQUEST_HSCLK_SHIFT;
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_CLKCTRL);
> +}
> +
> +void s5p_mipi_dsi_dp_dn_swap(struct mipi_dsim_device *dsim,
> +		unsigned int swap_en)
> +{
> +	unsigned int reg = readl(dsim->reg_base + S5P_DSIM_PHYACCHR1);
> +
> +	reg &= ~(0x3 << 0);
> +	reg |= (swap_en & 0x3) << 0;
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_PHYACCHR1);
> +}
> +
> +void s5p_mipi_dsi_hs_zero_ctrl(struct mipi_dsim_device *dsim,
> +		unsigned int hs_zero)
> +{
> +	unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_PLLCTRL)) &
> +		~(0xf << 28);
> +
> +	reg |= ((hs_zero & 0xf) << 28);
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_PLLCTRL);
> +}
> +
> +void s5p_mipi_dsi_prep_ctrl(struct mipi_dsim_device *dsim, unsigned int
prep)
> +{
> +	unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_PLLCTRL)) &
> +		~(0x7 << 20);
> +
> +	reg |= ((prep & 0x7) << 20);
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_PLLCTRL);
> +}
> +
> +void s5p_mipi_dsi_clear_interrupt(struct mipi_dsim_device *dsim)
> +{
> +	unsigned int reg = readl(dsim->reg_base + S5P_DSIM_INTSRC);
> +
> +	reg |= INTSRC_PLL_STABLE;
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_INTSRC);
> +}
> +
> +void s5p_mipi_dsi_clear_all_interrupt(struct mipi_dsim_device *dsim)
> +{
> +	unsigned int reg = readl(dsim->reg_base + S5P_DSIM_INTSRC);
> +
> +	reg |= 0xffffffff;
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_INTSRC);
> +}
> +
> +unsigned int s5p_mipi_dsi_is_pll_stable(struct mipi_dsim_device *dsim)
> +{
> +	unsigned int reg;
> +
> +	reg = readl(dsim->reg_base + S5P_DSIM_STATUS);
> +
> +	return reg & (1 << 31) ? 1 : 0;
> +}
> +
> +unsigned int s5p_mipi_dsi_get_fifo_state(struct mipi_dsim_device *dsim)
> +{
> +	unsigned int ret;
> +
> +	ret = readl(dsim->reg_base + S5P_DSIM_FIFOCTRL) & ~(0x1f);
> +
> +	return ret;
> +}
> +
> +void s5p_mipi_dsi_wr_tx_header(struct mipi_dsim_device *dsim,
> +	unsigned int di, unsigned int data0, unsigned int data1)
> +{
> +	unsigned int reg = (data1 << 16) | (data0 << 8) | ((di & 0x3f) <<
0);
> +
> +	writel(reg, dsim->reg_base + S5P_DSIM_PKTHDR);
> +}
> +
> +unsigned int _s5p_mipi_dsi_get_frame_done_status(struct mipi_dsim_device
> *dsim)
> +{
> +	unsigned int reg = readl(dsim->reg_base + S5P_DSIM_INTSRC);
> +
> +	return (reg & INTSRC_FRAME_DONE) ? 1 : 0;
> +}
> +
> +void _s5p_mipi_dsi_clear_frame_done(struct mipi_dsim_device *dsim)
> +{
> +	unsigned int reg = readl(dsim->reg_base + S5P_DSIM_INTSRC);
> +
> +	writel(reg | INTSRC_FRAME_DONE, dsim->reg_base +
> +		S5P_DSIM_INTSRC);
> +}
> +
> +void s5p_mipi_dsi_wr_tx_data(struct mipi_dsim_device *dsim,
> +		unsigned int tx_data)
> +{
> +	writel(tx_data, dsim->reg_base + S5P_DSIM_PAYLOAD);
> +}
> diff --git a/drivers/video/s5p_mipi_dsi_lowlevel.h
> b/drivers/video/s5p_mipi_dsi_lowlevel.h
> new file mode 100644
> index 0000000..ed3f91c
> --- /dev/null
> +++ b/drivers/video/s5p_mipi_dsi_lowlevel.h
> @@ -0,0 +1,98 @@
> +/* linux/drivers/video/s5p_mipi_dsi_lowlevel.h
> + *
> + * Header file for Samsung MIPI-DSI lowlevel driver.
> + *
> + * Copyright (c) 2009 Samsung Electronics
> + * InKi Dae <inki.dae at samsung.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> +*/
> +
> +#ifndef _S5P_MIPI_DSI_LOWLEVEL_H
> +#define _S5P_MIPI_DSI_LOWLEVEL_H
> +
> +void s5p_mipi_dsi_func_reset(struct mipi_dsim_device *dsim);
> +void s5p_mipi_dsi_sw_reset(struct mipi_dsim_device *dsim);
> +void s5p_mipi_dsi_set_interrupt_mask(struct mipi_dsim_device *dsim,
> +	unsigned int mode, unsigned int mask);
> +void s5p_mipi_dsi_set_data_lane_number(struct mipi_dsim_device *dsim,
> +					unsigned int count);
> +void s5p_mipi_dsi_init_fifo_pointer(struct mipi_dsim_device *dsim,
> +					unsigned int cfg);
> +void s5p_mipi_dsi_set_phy_tunning(struct mipi_dsim_device *dsim,
> +				unsigned int value);
> +void s5p_mipi_dsi_set_phy_tunning(struct mipi_dsim_device *dsim,
> +				unsigned int value);
> +void s5p_mipi_dsi_set_main_disp_resol(struct mipi_dsim_device *dsim,
> +		unsigned int vert_resol, unsigned int hori_resol);
> +void s5p_mipi_dsi_set_main_disp_vporch(struct mipi_dsim_device *dsim,
> +	unsigned int cmd_allow, unsigned int vfront, unsigned int vback);
> +void s5p_mipi_dsi_set_main_disp_hporch(struct mipi_dsim_device *dsim,
> +			unsigned int front, unsigned int back);
> +void s5p_mipi_dsi_set_main_disp_sync_area(struct mipi_dsim_device *dsim,
> +				unsigned int vert, unsigned int hori);
> +void s5p_mipi_dsi_set_sub_disp_resol(struct mipi_dsim_device *dsim,
> +				unsigned int vert, unsigned int hori);
> +void s5p_mipi_dsi_init_config(struct mipi_dsim_device *dsim);
> +void s5p_mipi_dsi_display_config(struct mipi_dsim_device *dsim,
> +				struct mipi_dsim_config *dsim_config);
> +void s5p_mipi_dsi_set_data_lane_number(struct mipi_dsim_device *dsim,
> +				unsigned int count);
> +void s5p_mipi_dsi_enable_lane(struct mipi_dsim_device *dsim, unsigned int
> lane,
> +				unsigned int enable);
> +void s5p_mipi_dsi_enable_afc(struct mipi_dsim_device *dsim, unsigned int
> enable,
> +				unsigned int afc_code);
> +void s5p_mipi_dsi_enable_pll_bypass(struct mipi_dsim_device *dsim,
> +				unsigned int enable);
> +void s5p_mipi_dsi_set_pll_pms(struct mipi_dsim_device *dsim, unsigned int
p,
> +				unsigned int m, unsigned int s);
> +void s5p_mipi_dsi_pll_freq_band(struct mipi_dsim_device *dsim,
> +				unsigned int freq_band);
> +void s5p_mipi_dsi_pll_freq(struct mipi_dsim_device *dsim,
> +			unsigned int pre_divider, unsigned int main_divider,
> +			unsigned int scaler);
> +void s5p_mipi_dsi_pll_stable_time(struct mipi_dsim_device *dsim,
> +			unsigned int lock_time);
> +void s5p_mipi_dsi_enable_pll(struct mipi_dsim_device *dsim,
> +					unsigned int enable);
> +void s5p_mipi_dsi_set_byte_clock_src(struct mipi_dsim_device *dsim,
> +					unsigned int src);
> +void s5p_mipi_dsi_enable_byte_clock(struct mipi_dsim_device *dsim,
> +					unsigned int enable);
> +void s5p_mipi_dsi_set_esc_clk_prs(struct mipi_dsim_device *dsim,
> +				unsigned int enable, unsigned int prs_val);
> +void s5p_mipi_dsi_enable_esc_clk_on_lane(struct mipi_dsim_device *dsim,
> +				unsigned int lane_sel, unsigned int enable);
> +void s5p_mipi_dsi_force_dphy_stop_state(struct mipi_dsim_device *dsim,
> +				unsigned int enable);
> +unsigned int s5p_mipi_dsi_is_lane_state(struct mipi_dsim_device *dsim);
> +void s5p_mipi_dsi_set_stop_state_counter(struct mipi_dsim_device *dsim,
> +				unsigned int cnt_val);
> +void s5p_mipi_dsi_set_bta_timeout(struct mipi_dsim_device *dsim,
> +				unsigned int timeout);
> +void s5p_mipi_dsi_set_lpdr_timeout(struct mipi_dsim_device *dsim,
> +				unsigned int timeout);
> +void s5p_mipi_dsi_set_lcdc_transfer_mode(struct mipi_dsim_device *dsim,
> +					unsigned int lp);
> +void s5p_mipi_dsi_set_cpu_transfer_mode(struct mipi_dsim_device *dsim,
> +					unsigned int lp);
> +void s5p_mipi_dsi_enable_hs_clock(struct mipi_dsim_device *dsim,
> +				unsigned int enable);
> +void s5p_mipi_dsi_dp_dn_swap(struct mipi_dsim_device *dsim,
> +				unsigned int swap_en);
> +void s5p_mipi_dsi_hs_zero_ctrl(struct mipi_dsim_device *dsim,
> +				unsigned int hs_zero);
> +void s5p_mipi_dsi_prep_ctrl(struct mipi_dsim_device *dsim, unsigned int
> prep);
> +void s5p_mipi_dsi_clear_interrupt(struct mipi_dsim_device *dsim);
> +void s5p_mipi_dsi_clear_all_interrupt(struct mipi_dsim_device *dsim);
> +unsigned int s5p_mipi_dsi_is_pll_stable(struct mipi_dsim_device *dsim);
> +unsigned int s5p_mipi_dsi_get_fifo_state(struct mipi_dsim_device *dsim);
> +unsigned int _s5p_mipi_dsi_get_frame_done_status(struct mipi_dsim_device
> *dsim);
> +void _s5p_mipi_dsi_clear_frame_done(struct mipi_dsim_device *dsim);
> +void s5p_mipi_dsi_wr_tx_header(struct mipi_dsim_device *dsim, unsigned
int
> di,
> +				unsigned int data0, unsigned int data1);
> +void s5p_mipi_dsi_wr_tx_data(struct mipi_dsim_device *dsim,
> +			unsigned int tx_data);
> +
> +#endif /* _S5P_MIPI_DSI_LOWLEVEL_H */
> --
> 1.7.0.4




More information about the linux-arm-kernel mailing list