[PATCH v2 1/2] OMAP: Add gpio-leds support for Overo
Steve Sakoman
steve at sakoman.com
Wed Mar 9 19:08:05 EST 2011
This patch adds support for the standard LEDs on the Overo COM and expansion boards
Signed-off-by: Steve Sakoman <steve at sakoman.com>
---
arch/arm/mach-omap2/board-overo.c | 53 +++++++++++++++++++++++++++++++++++++
1 files changed, 53 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c
index 4278ecb..e694ebd 100644
--- a/arch/arm/mach-omap2/board-overo.c
+++ b/arch/arm/mach-omap2/board-overo.c
@@ -473,6 +473,52 @@ static struct regulator_consumer_supply overo_vmmc1_supply = {
.supply = "vmmc",
};
+#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
+#include <linux/leds.h>
+
+static struct gpio_led gpio_leds[] = {
+ {
+ .name = "overo:red:gpio21",
+ .default_trigger = "heartbeat",
+ .gpio = 21,
+ .active_low = true,
+ },
+ {
+ .name = "overo:blue:gpio22",
+ .default_trigger = "none",
+ .gpio = 22,
+ .active_low = true,
+ },
+ {
+ .name = "overo:blue:COM",
+ .default_trigger = "mmc0",
+ .gpio = -EINVAL, /* gets replaced */
+ .active_low = true,
+ },
+};
+
+static struct gpio_led_platform_data gpio_leds_pdata = {
+ .leds = gpio_leds,
+ .num_leds = ARRAY_SIZE(gpio_leds),
+};
+
+static struct platform_device gpio_leds_device = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &gpio_leds_pdata,
+ },
+};
+
+static void __init overo_init_led(void)
+{
+ platform_device_register(&gpio_leds_device);
+}
+
+#else
+static inline void __init overo_init_led(void) { return; }
+#endif
+
static int overo_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
@@ -480,6 +526,11 @@ static int overo_twl_gpio_setup(struct device *dev,
overo_vmmc1_supply.dev = mmc[0].dev;
+#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
+ /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
+ gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
+#endif
+
return 0;
}
@@ -487,6 +538,7 @@ static struct twl4030_gpio_platform_data overo_gpio_data = {
.gpio_base = OMAP_MAX_GPIO_LINES,
.irq_base = TWL4030_GPIO_IRQ_BASE,
.irq_end = TWL4030_GPIO_IRQ_END,
+ .use_leds = true,
.setup = overo_twl_gpio_setup,
};
@@ -648,6 +700,7 @@ static void __init overo_init(void)
overo_spi_init();
overo_init_smsc911x();
overo_display_init();
+ overo_init_led();
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
--
1.7.0.4
More information about the linux-arm-kernel
mailing list