[PATCH V2 2/3] OMAP4: Update Voltage Rail Values for MPU/IVA

Nishanth Menon nm at ti.com
Mon Mar 7 21:06:54 EST 2011


Shweta Gulati wrote, on 03/05/2011 03:21 PM:
> Update MPU/IVA voltage Rail values obtained from
> OMAP4430 Data Manual Operating Condition Addendum_v0.3.
>
> Tested on OMAP4430 SDP Board.
>
> Signed-off-by: Shweta Gulati<shweta.gulati at ti.com>
> Cc: linux-arm-kernel at lists.infradead.org
> ---
>   arch/arm/mach-omap2/opp4xxx_data.c |   14 +++++++-------
>   1 files changed, 7 insertions(+), 7 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/opp4xxx_data.c b/arch/arm/mach-omap2/opp4xxx_data.c
> index 93b9744..36a4517 100644
> --- a/arch/arm/mach-omap2/opp4xxx_data.c
> +++ b/arch/arm/mach-omap2/opp4xxx_data.c
> @@ -31,10 +31,10 @@
>    * voltage dependent data for each VDD.
>    */
>
> -#define OMAP4430_VDD_MPU_OPP50_UV		930000
> -#define OMAP4430_VDD_MPU_OPP100_UV		1100000
> -#define OMAP4430_VDD_MPU_OPPTURBO_UV		1260000
> -#define OMAP4430_VDD_MPU_OPPNITRO_UV		1350000
> +#define OMAP4430_VDD_MPU_OPP50_UV		1025000
> +#define OMAP4430_VDD_MPU_OPP100_UV		1200000
> +#define OMAP4430_VDD_MPU_OPPTURBO_UV		1313000
> +#define OMAP4430_VDD_MPU_OPPNITRO_UV		1375000
>
>   struct omap_volt_data omap44xx_vdd_mpu_volt_data[] = {
>   	VOLT_DATA_DEFINE(OMAP4430_VDD_MPU_OPP50_UV, OMAP44XX_CONTROL_FUSE_MPU_OPP50, 0xf4, 0x0c),
> @@ -44,9 +44,9 @@ struct omap_volt_data omap44xx_vdd_mpu_volt_data[] = {
>   	VOLT_DATA_DEFINE(0, 0, 0, 0),
>   };
>
> -#define OMAP4430_VDD_IVA_OPP50_UV		930000
> -#define OMAP4430_VDD_IVA_OPP100_UV		1100000
> -#define OMAP4430_VDD_IVA_OPPTURBO_UV		1260000
> +#define OMAP4430_VDD_IVA_OPP50_UV		1013000
> +#define OMAP4430_VDD_IVA_OPP100_UV		1188000
> +#define OMAP4430_VDD_IVA_OPPTURBO_UV		1300000
>
>   struct omap_volt_data omap44xx_vdd_iva_volt_data[] = {
>   	VOLT_DATA_DEFINE(OMAP4430_VDD_IVA_OPP50_UV, OMAP44XX_CONTROL_FUSE_IVA_OPP50, 0xf4, 0x0c),
Acked-by: Nishanth Menon <nm at ti.com>


Side note: unrelated to this patch: PMICs have discrete step sizes of 
10mV, 12.5, 25mV etc.. which makes something lik 1.118V probably not 
exactly possible on a PMIC with 25mV step. We need to next probably 
create a framework to round_up the voltages to the PMIC step size once 
the PMIC voltage layer changes are in.

-- 
Regards,
Nishanth Menon



More information about the linux-arm-kernel mailing list