[PATCHv3 2/4] mach-mx31_3ds: Add support for the MMC slot of the personality board

[Alberto Panizzo]

Signed-off-by: Alberto Panizzo <alberto at amarulasolutions.com>
---
 arch/arm/mach-mx3/mach-mx31_3ds.c |   99 +++++++++++++++++++++++++++++++++++++
 1 files changed, 99 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-mx3/mach-mx31_3ds.c b/arch/arm/mach-mx3/mach-mx31_3ds.c
index f1dbb9d..cff9206 100644
--- a/arch/arm/mach-mx3/mach-mx31_3ds.c
+++ b/arch/arm/mach-mx3/mach-mx31_3ds.c
@@ -35,6 +35,7 @@
 #include <mach/iomux-mx3.h>
 #include <mach/3ds_debugboard.h>
 #include <mach/ulpi.h>
+#include <mach/mmc.h>
 
 #include "devices-imx31.h"
 #include "devices.h"
@@ -99,6 +100,85 @@ static int mx31_3ds_pins[] = {
 	/* I2C1 */
 	MX31_PIN_I2C_CLK__I2C1_SCL,
 	MX31_PIN_I2C_DAT__I2C1_SDA,
+	/* SDHC1 */
+	MX31_PIN_SD1_DATA3__SD1_DATA3,
+	MX31_PIN_SD1_DATA2__SD1_DATA2,
+	MX31_PIN_SD1_DATA1__SD1_DATA1,
+	MX31_PIN_SD1_DATA0__SD1_DATA0,
+	MX31_PIN_SD1_CLK__SD1_CLK,
+	MX31_PIN_SD1_CMD__SD1_CMD,
+	MX31_PIN_GPIO3_1__GPIO3_1, /* Card detect */
+	MX31_PIN_GPIO3_0__GPIO3_0, /* OE */
+};
+
+/*
+ * Support for SD card slot in personality board
+ */
+#define MX31_3DS_GPIO_SDHC1_CD IOMUX_TO_GPIO(MX31_PIN_GPIO3_1)
+#define MX31_3DS_GPIO_SDHC1_BE IOMUX_TO_GPIO(MX31_PIN_GPIO3_0)
+
+static struct gpio mx31_3ds_sdhc1_gpios[] = {
+	{ MX31_3DS_GPIO_SDHC1_CD, GPIOF_IN, "sdhc1-card-detect" },
+	{ MX31_3DS_GPIO_SDHC1_BE, GPIOF_OUT_INIT_LOW, "sdhc1-bus-en" },
+};
+
+static int mx31_3ds_sdhc1_init(struct device *dev,
+			       irq_handler_t detect_irq,
+			       void *data)
+{
+	int ret;
+
+	ret = gpio_request_array(mx31_3ds_sdhc1_gpios,
+				 ARRAY_SIZE(mx31_3ds_sdhc1_gpios));
+	if (ret) {
+		pr_warning("Unable to request the SD/MMC GPIOs.\n");
+		return ret;
+	}
+
+	ret = request_irq(IOMUX_TO_IRQ(MX31_PIN_GPIO3_1),
+			  detect_irq, IRQF_DISABLED |
+			  IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
+			  "sdhc1-detect", data);
+	if (ret) {
+		pr_warning("Unable to request the SD/MMC card-detect IRQ.\n");
+		goto gpio_free;
+	}
+
+	return 0;
+
+gpio_free:
+	gpio_free_array(mx31_3ds_sdhc1_gpios,
+			ARRAY_SIZE(mx31_3ds_sdhc1_gpios));
+	return ret;
+}
+
+static void mx31_3ds_sdhc1_exit(struct device *dev, void *data)
+{
+	free_irq(IOMUX_TO_IRQ(MX31_PIN_GPIO3_1), data);
+	gpio_free_array(mx31_3ds_sdhc1_gpios,
+			 ARRAY_SIZE(mx31_3ds_sdhc1_gpios));
+}
+
+static void mx31_3ds_sdhc1_setpower(struct device *dev, unsigned int vdd)
+{
+	/*
+	 * While the voltage stuff is done by the driver, activate the
+	 * Buffer Enable Pin only if there is a card in slot to fix the card
+	 * voltage issue caused by bi-directional chip TXB0108 on 3Stack.
+	 * Done here because at this stage we have for sure a debounced value
+	 * of the presence of the card, showed by the value of vdd.
+	 * 7 == ilog2(MMC_VDD_165_195)
+	 */
+	if (vdd > 7)
+		gpio_set_value(MX31_3DS_GPIO_SDHC1_BE, 1);
+	else
+		gpio_set_value(MX31_3DS_GPIO_SDHC1_BE, 0);
+}
+
+static struct imxmmc_platform_data sdhc1_pdata = {
+	.init		= mx31_3ds_sdhc1_init,
+	.exit		= mx31_3ds_sdhc1_exit,
+	.setpower	= mx31_3ds_sdhc1_setpower,
 };
 
 /*
@@ -137,6 +217,21 @@ static struct regulator_init_data gpo_init = {
 	}
 };
 
+static struct regulator_consumer_supply vmmc2_consumers[] = {
+	REGULATOR_SUPPLY("vmmc", "mxc-mmc.0"),
+};
+
+static struct regulator_init_data vmmc2_init = {
+	.constraints = {
+		.min_uV = 3000000,
+		.max_uV = 3000000,
+		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
+				  REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies = ARRAY_SIZE(vmmc2_consumers),
+	.consumer_supplies = vmmc2_consumers,
+};
+
 static struct mc13xxx_regulator_init_data mx31_3ds_regulators[] = {
 	{
 		.id = MC13783_REG_PWGT1SPI, /* Power Gate for ARM core. */
@@ -151,6 +246,9 @@ static struct mc13xxx_regulator_init_data mx31_3ds_regulators[] = {
 	}, {
 		.id = MC13783_REG_GPO3, /* Turn on 3.3V */
 		.init_data = &gpo_init,
+	}, {
+		.id = MC13783_REG_VMMC2, /* Power MMC/SD, WiFi/Bluetooth. */
+		.init_data = &vmmc2_init,
 	},
 };
 
@@ -362,6 +460,7 @@ static void __init mx31_3ds_init(void)
 				    "devices on the debug board are unusable.\n");
 	imx31_add_imx2_wdt(NULL);
 	imx31_add_imx_i2c0(&mx31_3ds_i2c0_data);
+	imx31_add_mxc_mmc(0, &sdhc1_pdata);
 }
 
 static void __init mx31_3ds_timer_init(void)
-- 
1.7.1