[PATCH 2/4] mach-mx31_3ds: Add support for the MMC slot of the personality board

Alberto Panizzo alberto at amarulasolutions.com
Mon Mar 7 04:06:31 EST 2011


On Mon, 2011-03-07 at 09:27 +0100, Sascha Hauer wrote:
> On Sun, Mar 06, 2011 at 04:40:01PM +0100, Alberto Panizzo wrote:
> > 
> > 
> > Signed-off-by: Alberto Panizzo <alberto at amarulasolutions.com>
> > ---
> >  arch/arm/mach-mx3/mach-mx31_3ds.c |  116 ++++++++++++++++++++++++++++++++++++-
> >  1 files changed, 114 insertions(+), 2 deletions(-)
> > 
> > diff --git a/arch/arm/mach-mx3/mach-mx31_3ds.c b/arch/arm/mach-mx3/mach-mx31_3ds.c
> > index f1dbb9d..cd73513 100644
> > --- a/arch/arm/mach-mx3/mach-mx31_3ds.c
> > +++ b/arch/arm/mach-mx3/mach-mx31_3ds.c
> > @@ -35,6 +35,7 @@
> >  #include <mach/iomux-mx3.h>
> >  #include <mach/3ds_debugboard.h>
> >  #include <mach/ulpi.h>
> > +#include <mach/mmc.h>
> >  
> >  #include "devices-imx31.h"
> >  #include "devices.h"
> > @@ -99,6 +100,98 @@ static int mx31_3ds_pins[] = {
> >  	/* I2C1 */
> >  	MX31_PIN_I2C_CLK__I2C1_SCL,
> >  	MX31_PIN_I2C_DAT__I2C1_SDA,
> > +	/* SDHC1 */
> > +	MX31_PIN_SD1_DATA3__SD1_DATA3,
> > +	MX31_PIN_SD1_DATA2__SD1_DATA2,
> > +	MX31_PIN_SD1_DATA1__SD1_DATA1,
> > +	MX31_PIN_SD1_DATA0__SD1_DATA0,
> > +	MX31_PIN_SD1_CLK__SD1_CLK,
> > +	MX31_PIN_SD1_CMD__SD1_CMD,
> > +	MX31_PIN_GPIO3_1__GPIO3_1, /* Card detect */
> > +	MX31_PIN_GPIO3_0__GPIO3_0, /* OE */
> > +};
> > +
> > +/*
> > + * Support for SD card slot in personality board
> > + */
> > +static int mx31_3ds_sdhc1_init(struct device *dev, irq_handler_t detect_irq,
> > +			       void *data)
> > +{
> > +	int ret;
> > +	int gpio_det, gpio_bus_en;
> > +
> > +	gpio_det = IOMUX_TO_GPIO(MX31_PIN_GPIO3_1);
> > +	gpio_bus_en = IOMUX_TO_GPIO(MX31_PIN_GPIO3_0);
> > +
> > +	ret = gpio_request(gpio_det, "sdhc1-card-detect");
> > +	if (ret) {
> > +		pr_warning("Unable to request the SD/MMC card-detect GPIO.\n");
> > +		return ret;
> > +	}
> > +
> > +	ret = gpio_request(gpio_bus_en, "sdhc1-bus-enable");
> > +	if (ret) {
> > +		pr_warning("Unable to request the SD/MMC bus enable GPIO.\n");
> > +		goto gpio_free_be;
> > +	}
> > +
> > +	ret = gpio_direction_input(gpio_det);
> > +	if (ret) {
> > +		pr_warning("Unable to manage the SD/MMC card-detect GPIO.\n");
> > +		goto gpio_free_all;
> > +	}
> > +
> > +	ret = gpio_direction_output(gpio_bus_en, 0);
> > +	if (ret) {
> > +		pr_warning("Unable to manage the SD/MMC bus enable GPIO.\n");
> > +		goto gpio_free_all;
> > +	}
> 
> Wolfram just arrived, so I probably have some moments left before he
> says it: You should use gpio_request_array here.

Ok I'll check the API.

> 
> > +
> > +	ret = request_irq(IOMUX_TO_IRQ(MX31_PIN_GPIO3_1),
> > +			  detect_irq, IRQF_DISABLED |
> > +			  IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
> > +			  "sdhc1-detect", data);
> > +	if (ret) {
> > +		pr_warning("Unable to request the SD/MMC card-detect IRQ.\n");
> > +		goto gpio_free_all;
> > +	}
> > +
> > +	return 0;
> > +
> > +gpio_free_all:
> > +	gpio_free(gpio_bus_en);
> > +gpio_free_be:
> > +	gpio_free(gpio_det);
> > +	return ret;
> > +}
> > +
> > +static void mx31_3ds_sdhc1_exit(struct device *dev, void *data)
> > +{
> > +	free_irq(IOMUX_TO_IRQ(MX31_PIN_GPIO3_1), data);
> > +	gpio_free(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1));
> > +	gpio_free(IOMUX_TO_GPIO(MX31_PIN_GPIO3_0));
> > +}
> > +
> > +static void mx31_3ds_sdhc1_setpower(struct device *dev, unsigned int vdd)
> > +{
> > +	/*
> > +	 * While the voltage stuff is done by the driver, activate the
> > +	 * Buffer Enable Pin only if there is a card in slot to fix the card
> > +	 * voltage issue caused by bi-directional chip TXB0108 on 3Stack.
> > +	 * Done here because at this stage we have for sure a debounced value
> > +	 * of the presence of the card, showed by the value of vdd.
> > +	 * 7 == ilog2(MMC_VDD_165_195)
> > +	 */
> > +	if (vdd > 7)
> > +		gpio_set_value(IOMUX_TO_GPIO(MX31_PIN_GPIO3_0), 1);
> > +	else
> > +		gpio_set_value(IOMUX_TO_GPIO(MX31_PIN_GPIO3_0), 0);
> > +}
> > +
> > +static struct imxmmc_platform_data sdhc1_pdata = {
> > +	.init	= mx31_3ds_sdhc1_init,
> > +	.exit	= mx31_3ds_sdhc1_exit,
> > +	.setpower = mx31_3ds_sdhc1_setpower,
> >  };
> >  
> >  /*
> > @@ -132,11 +225,26 @@ static struct regulator_init_data pwgtx_init = {
> >  
> >  static struct regulator_init_data gpo_init = {
> >  	.constraints = {
> > -		.boot_on = 1,
> > -		.always_on = 1,
> > +		.boot_on	= 1,
> > +		.always_on	= 1,
> >  	}
> >  };
> 
> 
> Please just keep it as it is. Some people like the initializers
> vertically aligned, others prefer spaces here. But if someone made
> a decision, don't change it to increase the chance that git blame
> shows something useful.

OK but indeed I've done it for consistency with all the rest of the
file.
A new version soon.

Alberto!
-- 
| Alberto Panizzo                                 Amarula Solutions BV |
| CTO  -  Founder                                      Cruquiuskade 47 |
| T. +31(0)851119171                              Amsterdam 1018 AM NL |
| F. +31(0)204106211                          www.amarulasolutions.com |




More information about the linux-arm-kernel mailing list