[PATCH 6/7] OMAP: Serial: Allow UART parameters to be configured from board file

[Govindraj]

On Wed, Mar 2, 2011 at 12:46 AM, Sricharan R <r.sricharan at ti.com> wrote:
> Hi,
>>diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
>>index 755f4aa..530e9e3 100644
>>--- a/arch/arm/mach-omap2/serial.c
>>+++ b/arch/arm/mach-omap2/serial.c
>>@@ -44,6 +44,15 @@
>>
>> static int omap_uart_con_id __initdata = -1;
>>
>>+static struct omap_uart_port_info omap_serial_default_info[] = {
>>+      {
>>+              .dma_enabled    = 0,
>>+              .dma_rx_buf_size = DEFAULT_RXDMA_BUFSIZE,
>>+              .dma_rx_timeout = DEFAULT_RXDMA_TIMEOUT,
>>+              .idle_timeout   = DEFAULT_IDLE_TIMEOUT,
>>+      },
>>+};
>>+
>> static int uart_idle_hwmod(struct omap_device *od)
>> {
>>       omap_hwmod_idle(od->hwmods[0]);
>>@@ -66,6 +75,54 @@ static struct omap_device_pm_latency
> omap_uart_latency[]
>>= {
>>       },
>> };
>>
>>+#ifdef CONFIG_OMAP_MUX
>>+static struct omap_device_pad default_serial0_pads[] __initdata = {
>>+      {
>>+              .name   = "uart1_rx.uart1_rx",
>>+              .flags  = OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
>>+              .enable = OMAP_MUX_MODE0,
>>+      },
>>+};
>>+
>>+static struct omap_device_pad default_serial1_pads[] __initdata = {
>>+      {
>>+              .name   = "uart2_rx.uart2_rx",
>>+              .flags  = OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
>>+              .enable = OMAP_MUX_MODE0,
>>+      },
>>+};
>>+
>>+static struct omap_device_pad default_serial2_pads[] __initdata = {
>>+      {
>>+              .name   = "uart3_rx_irrx.uart3_rx_irrx",
>>+              .flags  = OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
>>+              .enable = OMAP_MUX_MODE0,
>>+      },
>>+};
>>+
>>+static struct omap_device_pad default_omap36xx_serial3_pads[] __initdata
> =
>>{
>>+      {
>>+              .name   = "gpmc_wait3.uart4_rx",
>>+              .flags  = OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
>>+              .enable = OMAP_MUX_MODE2,
>>+      },
>>+};
>>+
>>+static struct omap_device_pad default_omap4_serial3_pads[] __initdata =
> {
>>+      {
>>+              .name   = "uart4_rx.uart4_rx",
>>+              .flags  = OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
>>+              .enable = OMAP_MUX_MODE0,
>>+      },
>>+};
> Here only the UART RX pins are muxed, so what about the cts, rts, tx pins?

The intention here is to enable wakeup capabilities for uart rx pad.

AFAIK most of the boards are currently dependent on bootloader for
uart-muxing if any board is not dependent on bootloader then we
can use omap_serial_init_port along with board_mux_info from board.

Prior to this change uart wakeup is based on rx_pad and we were populating
offset and using omap_ctrl api's to read/write which is cleaned up now.
Most of boards are dependent on uart-rx wakeup to avoid breaking any
board support we
are using omap_serial_init by filling default values, which provides
us with same
environment but with right approach towards handling mux data with a
handshake with
hwmod framework.

So if any board needs specific mux they can go ahead and add required
mux data in
board file and use map_serial_init_port instead of current omap_serial_init.


> Is it consistent that across all socs that only UART3 would have UART/IRDA
> functions capability so that serial2 pads can always be called "rx_irxx"
> ?.

Yes from OMAP2420 to OMAP4430 uart3 can used as irda.

--
Thanks,
Govindraj.R