[PATCH 3/7] ARM: mmp: support DT on both dkb and brownstone
Haojian Zhuang
haojian.zhuang at marvell.com
Mon Jul 18 22:24:46 EDT 2011
Add new boards.c to support both TTC-DKB and MMP2-BROWNSTONE. While
CONFIG_MMP_USE_OF is selected, original ttc_dkb.c and brownstone.c won't be
compiled.
While everything moving to DT in ARCH-MMP, original ttc_dkb.c and brownstone.c
will be abandoned.
Signed-off-by: Haojian Zhuang <haojian.zhuang at marvell.com>
---
.../devicetree/bindings/arm/marvell/boards.txt | 7 +
arch/arm/boot/dts/mmp2-brownstone.dts | 242 ++++++++++++++++++++
arch/arm/boot/dts/ttc-dkb.dts | 80 +++++++
arch/arm/mach-mmp/Makefile | 4 +
arch/arm/mach-mmp/boards.c | 159 +++++++++++++
5 files changed, 492 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/arm/marvell/boards.txt
create mode 100644 arch/arm/boot/dts/mmp2-brownstone.dts
create mode 100644 arch/arm/boot/dts/ttc-dkb.dts
create mode 100644 arch/arm/mach-mmp/boards.c
diff --git a/Documentation/devicetree/bindings/arm/marvell/boards.txt b/Documentation/devicetree/bindings/arm/marvell/boards.txt
new file mode 100644
index 0000000..219e134
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/marvell/boards.txt
@@ -0,0 +1,7 @@
+TTC(pxa910) "DKB" evalutation board
+Required root node properties:
+ - compatible = "mrvl,ttc-dkb", "mrvl,pxa910-dkb";
+
+mmp2(armada610) "Brownstone" evalutation board
+Required root node properties:
+ - compatible = "mrvl,mmp2-brownstone", "mrvl,armada610-brownstone";
diff --git a/arch/arm/boot/dts/mmp2-brownstone.dts b/arch/arm/boot/dts/mmp2-brownstone.dts
new file mode 100644
index 0000000..4e14388
--- /dev/null
+++ b/arch/arm/boot/dts/mmp2-brownstone.dts
@@ -0,0 +1,242 @@
+/dts-v1/;
+
+/include/ "skeleton.dtsi"
+
+/ {
+ model = "Marvell MMP2 Brownstone";
+ compatible = "mrvl,mmp2-brownstone", "mrvl,armada610-brownstone";
+
+ memory {
+ reg = <0x00000000 0x20000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS2,38400 root=/dev/nfs nfsroot=192.168.1.100:192.168.1.101::255.255.255.0::eth0:on";
+ linux,stdout-path = &uart2;
+ };
+
+ soc at d4000000 {
+ compatible = "mrvl,mmp2", "mrvl,armada610", "simple-bus";
+ device_type = "soc";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mmp_intc: interrupt-controller at d4282000 {
+ compatible = "mrvl,mmp-intc";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ /* reg: <offset & size> */
+ reg = <0xd4282000 0x400>;
+
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ intc-numbers = <64>;
+ /* enable bits in conf register */
+ intc-enable-mask = <0x20>;
+ };
+
+ mux_intc4: interrupt-controller at d4282150 {
+ compatible = "mrvl,mux-intc";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xd4282150 0>;
+
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ interrupt-parent = <&mmp_intc>;
+ interrupts = <4>;
+ intc-numbers = <2>;
+ intc-status = <0x150>;
+ intc-mask = <0x168>;
+ /* mfp register & interrupt index */
+ intc-mfp-edge = <0xd401e2c4 1>;
+ };
+
+ mux_intc5: interrupt-controller at d4282154 {
+ compatible = "mrvl,mux-intc";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xd4282154 0>;
+
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ interrupt-parent = <&mmp_intc>;
+ interrupts = <5>;
+ intc-numbers = <2>;
+ intc-status = <0x154>;
+ intc-mask = <0x16c>;
+ };
+
+ mux_intc9: interrupt-controller at d4282180 {
+ compatible = "mrvl,mux-intc";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xd4282180 0>;
+
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ interrupt-parent = <&mmp_intc>;
+ interrupts = <9>;
+ intc-numbers = <3>;
+ intc-status = <0x180>;
+ intc-mask = <0x17c>;
+ };
+
+ mux_intc17: interrupt-controller at d4282158 {
+ compatible = "mrvl,mux-intc";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xd4282158 0>;
+
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ interrupt-parent = <&mmp_intc>;
+ interrupts = <17>;
+ intc-numbers = <5>;
+ intc-status = <0x158>;
+ intc-mask = <0x170>;
+ };
+
+ mux_intc35: interrupt-controller at d428215c {
+ compatible = "mrvl,mux-intc";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xd428215c 0>;
+
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ interrupt-parent = <&mmp_intc>;
+ interrupts = <35>;
+ intc-numbers = <15>;
+ intc-status = <0x15c>;
+ intc-mask = <0x174>;
+ };
+
+ mux_intc51: interrupt-controller at d4282160 {
+ compatible = "mrvl,mux-intc";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xd4282160 0>;
+
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ interrupt-parent = <&mmp_intc>;
+ interrupts = <51>;
+ intc-numbers = <2>;
+ intc-status = <0x160>;
+ intc-mask = <0x178>;
+ };
+
+ mux_intc55: interrupt-controller at d4282188 {
+ compatible = "mrvl,mux-intc";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xd4282188 0>;
+
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ interrupt-parent = <&mmp_intc>;
+ interrupts = <55>;
+ intc-numbers = <2>;
+ intc-status = <0x188>;
+ intc-mask = <0x184>;
+ };
+
+ i2c0: i2c at d4011000 {
+ compatible = "mrvl,pxa255-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0xd4011000 0x60>;
+ i2c-polling = <0>;
+ i2c-frequency = "fast";
+ interrupts = <7>;
+ interrupt-parent = <&mmp_intc>;
+ };
+
+ i2c1: i2c at d4031000 {
+ compatible = "mrvl,pxa255-i2c";
+ reg = <0xd4031000 0x60>;
+ i2c-polling = <0>;
+ i2c-frequency = "fast";
+ interrupts = <0>;
+ interrupt-parent = <&mux_intc17>;
+ };
+
+ i2c2: i2c at d4032000 {
+ compatible = "mrvl,pxa255-i2c";
+ reg = <0xd4032000 0x60>;
+ i2c-polling = <0>;
+ i2c-frequency = "fast";
+ interrupts = <1>;
+ interrupt-parent = <&mux_intc17>;
+ };
+
+ i2c3: i2c at d4033000 {
+ compatible = "mrvl,pxa255-i2c";
+ reg = <0xd4033000 0x60>;
+ i2c-polling = <0>;
+ i2c-frequency = "fast";
+ interrupts = <2>;
+ interrupt-parent = <&mux_intc17>;
+ };
+
+ i2c4: i2c at d4033800 {
+ compatible = "mrvl,pxa255-i2c";
+ reg = <0xd4033800 0x60>;
+ i2c-polling = <0>;
+ i2c-frequency = "fast";
+ interrupts = <3>;
+ interrupt-parent = <&mux_intc17>;
+ };
+
+ i2c5: i2c at d4034000 {
+ compatible = "mrvl,pxa255-i2c";
+ reg = <0xd4034000 0x60>;
+ i2c-polling = <0>;
+ i2c-frequency = "fast";
+ interrupts = <4>;
+ interrupt-parent = <&mux_intc17>;
+ };
+
+ uart0: uart at d4030000 {
+ compatible = "mrvl,pxa270-serial";
+ reg = <0xd4030000 0x1000>;
+ reg-shift = <2>;
+ interrupts = <27>;
+ interrupt-parent = <&mmp_intc>;
+ clock-frequency = <26000000>;
+ current-speed = <115200>;
+ };
+
+ uart1: uart at d4017000 {
+ compatible = "mrvl,pxa270-serial";
+ reg = <0xd4017000 0x1000>;
+ reg-shift = <2>;
+ interrupts = <28>;
+ interrupt-parent = <&mmp_intc>;
+ clock-frequency = <26000000>;
+ current-speed = <115200>;
+ };
+
+ uart2: uart at d4018000 {
+ compatible = "mrvl,pxa270-serial";
+ reg = <0xd4018000 0x1000>;
+ reg-shift = <2>;
+ interrupts = <24>;
+ interrupt-parent = <&mmp_intc>;
+ clock-frequency = <26000000>;
+ current-speed = <38400>;
+ };
+
+ uart3: uart at d4016000 {
+ compatible = "mrvl,pxa270-serial";
+ reg = <0xd4016000 0x1000>;
+ reg-shift = <2>;
+ interrupts = <46>;
+ interrupt-parent = <&mmp_intc>;
+ clock-frequency = <26000000>;
+ current-speed = <115200>;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/ttc-dkb.dts b/arch/arm/boot/dts/ttc-dkb.dts
new file mode 100644
index 0000000..ff8df4f
--- /dev/null
+++ b/arch/arm/boot/dts/ttc-dkb.dts
@@ -0,0 +1,80 @@
+/dts-v1/;
+
+/include/ "skeleton.dtsi"
+
+/ {
+ model = "Marvell TTC DKB";
+ compatible = "mrvl,ttc-dkb", "mrvl,pxa910-dkb";
+
+ memory {
+ reg = <0x00000000 0x20000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200 root=/dev/nfs nfsroot=192.168.1.100:192.168.1.101::255.255.255.0::eth0:on";
+ linux,stdout-path = &uart0;
+ };
+
+ soc at d4000000 {
+ compatible = "mrvl,pxa910", "simple-bus";
+ device_type = "soc";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0xd4000000 0xd4000000 0x00200000 /* APB */
+ 0xd4200000 0xd4200000 0x00200000>; /* AXI */
+
+ mmp_intc: interrupt-controller at d4282000 {
+ compatible = "mrvl,mmp-intc";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ /* reg: <offset & size> */
+ reg = <0xd4282000 0x400>;
+
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ intc-numbers = <64>;
+ /* enable bits in conf register */
+ intc-enable-mask = <0x51>;
+ };
+
+ i2c0: i2c at d4011000 {
+ compatible = "mrvl,pxa255-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0xd4011000 0x60>;
+ i2c-polling = <0>;
+ i2c-frequency = "fast";
+ interrupts = <7>;
+ interrupt-parent = <&mmp_intc>;
+ };
+
+ i2c1: i2c at d4037000 {
+ compatible = "mrvl,pxa255-i2c";
+ reg = <0xd4037000 0x60>;
+ i2c-polling = <0>;
+ i2c-frequency = "fast";
+ interrupts = <54>;
+ interrupt-parent = <&mmp_intc>;
+ };
+
+ uart0: uart at d4017000 {
+ compatible = "mrvl,pxa270-serial";
+ reg = <0xd4017000 0x1000>;
+ reg-shift = <2>;
+ interrupts = <27>;
+ interrupt-parent = <&mmp_intc>;
+ clock-frequency = <14745600>;
+ current-speed = <115200>;
+ };
+
+ uart1: uart at d4018000 {
+ compatible = "mrvl,pxa270-serial";
+ reg = <0xd4018000 0x1000>;
+ reg-shift = <2>;
+ interrupts = <28>;
+ interrupt-parent = <&mmp_intc>;
+ clock-frequency = <14745600>;
+ current-speed = <115200>;
+ };
+ };
+};
diff --git a/arch/arm/mach-mmp/Makefile b/arch/arm/mach-mmp/Makefile
index e7862ea..6c39bbd 100644
--- a/arch/arm/mach-mmp/Makefile
+++ b/arch/arm/mach-mmp/Makefile
@@ -12,6 +12,9 @@ obj-$(CONFIG_CPU_PXA910) += pxa910.o irq-pxa168.o
obj-$(CONFIG_CPU_MMP2) += mmp2.o irq-mmp2.o
# board support
+ifeq ($(CONFIG_MMP_USE_OF),y)
+obj-$(CONFIG_OF) += boards.o
+else
obj-$(CONFIG_MACH_ASPENITE) += aspenite.o
obj-$(CONFIG_MACH_ZYLONITE2) += aspenite.o
obj-$(CONFIG_MACH_AVENGERS_LITE)+= avengers_lite.o
@@ -21,3 +24,4 @@ obj-$(CONFIG_MACH_BROWNSTONE) += brownstone.o
obj-$(CONFIG_MACH_FLINT) += flint.o
obj-$(CONFIG_MACH_MARVELL_JASPER) += jasper.o
obj-$(CONFIG_MACH_TETON_BGA) += teton_bga.o
+endif
diff --git a/arch/arm/mach-mmp/boards.c b/arch/arm/mach-mmp/boards.c
new file mode 100644
index 0000000..31c8e84
--- /dev/null
+++ b/arch/arm/mach-mmp/boards.c
@@ -0,0 +1,159 @@
+/*
+ * linux/arch/arm/mach-mmp/boards.c
+ *
+ * Support for the Multiple Marvell Development Platforms.
+ *
+ * Copyright (C) 2009-2011 Marvell International Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * publishhed by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/of.h>
+#include <linux/of_fdt.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/i2c/pxa-i2c.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#include <mach/pxa910.h>
+#include <mach/mmp2.h>
+#include <mach/mfp-mmp2.h>
+
+#include "common.h"
+
+static struct of_device_id of_bus_ids[] __initdata = {
+ { .compatible = "simple-bus", },
+ {},
+};
+
+static struct of_dev_auxdata ttc_dkb_auxdata_lookup[] __initdata = {
+ {}
+};
+
+static void __init ttc_dkb_init(void)
+{
+ if (of_platform_populate(NULL, of_bus_ids, ttc_dkb_auxdata_lookup,
+ NULL) < 0)
+ BUG();
+}
+
+static const char *ttc_dkb_dt_match[] __initdata = {
+ "mrvl,ttc-dkb",
+ NULL,
+};
+
+#ifdef CONFIG_CPU_PXA910
+MACHINE_START(TTC_DKB, "PXA910-based TTC-DKB Development Platform")
+ .map_io = mmp_map_io,
+ .init_irq = mmp_init_intc,
+ .timer = &pxa910_timer,
+ .init_machine = ttc_dkb_init,
+ .dt_compat = ttc_dkb_dt_match,
+MACHINE_END
+#endif
+
+static unsigned long brownstone_pin_config[] __initdata = {
+ /* UART1 */
+ GPIO29_UART1_RXD,
+ GPIO30_UART1_TXD,
+
+ /* UART3 */
+ GPIO51_UART3_RXD,
+ GPIO52_UART3_TXD,
+
+ /* DFI */
+ GPIO168_DFI_D0,
+ GPIO167_DFI_D1,
+ GPIO166_DFI_D2,
+ GPIO165_DFI_D3,
+ GPIO107_DFI_D4,
+ GPIO106_DFI_D5,
+ GPIO105_DFI_D6,
+ GPIO104_DFI_D7,
+ GPIO111_DFI_D8,
+ GPIO164_DFI_D9,
+ GPIO163_DFI_D10,
+ GPIO162_DFI_D11,
+ GPIO161_DFI_D12,
+ GPIO110_DFI_D13,
+ GPIO109_DFI_D14,
+ GPIO108_DFI_D15,
+ GPIO143_ND_nCS0,
+ GPIO144_ND_nCS1,
+ GPIO147_ND_nWE,
+ GPIO148_ND_nRE,
+ GPIO150_ND_ALE,
+ GPIO149_ND_CLE,
+ GPIO112_ND_RDY0,
+ GPIO160_ND_RDY1,
+
+ /* PMIC */
+ PMIC_PMIC_INT | MFP_LPM_EDGE_FALL,
+
+ /* MMC0 */
+ GPIO131_MMC1_DAT3 | MFP_PULL_HIGH,
+ GPIO132_MMC1_DAT2 | MFP_PULL_HIGH,
+ GPIO133_MMC1_DAT1 | MFP_PULL_HIGH,
+ GPIO134_MMC1_DAT0 | MFP_PULL_HIGH,
+ GPIO136_MMC1_CMD | MFP_PULL_HIGH,
+ GPIO139_MMC1_CLK,
+ GPIO140_MMC1_CD | MFP_PULL_LOW,
+ GPIO141_MMC1_WP | MFP_PULL_LOW,
+
+ /* MMC1 */
+ GPIO37_MMC2_DAT3 | MFP_PULL_HIGH,
+ GPIO38_MMC2_DAT2 | MFP_PULL_HIGH,
+ GPIO39_MMC2_DAT1 | MFP_PULL_HIGH,
+ GPIO40_MMC2_DAT0 | MFP_PULL_HIGH,
+ GPIO41_MMC2_CMD | MFP_PULL_HIGH,
+ GPIO42_MMC2_CLK,
+
+ /* MMC2 */
+ GPIO165_MMC3_DAT7 | MFP_PULL_HIGH,
+ GPIO162_MMC3_DAT6 | MFP_PULL_HIGH,
+ GPIO166_MMC3_DAT5 | MFP_PULL_HIGH,
+ GPIO163_MMC3_DAT4 | MFP_PULL_HIGH,
+ GPIO167_MMC3_DAT3 | MFP_PULL_HIGH,
+ GPIO164_MMC3_DAT2 | MFP_PULL_HIGH,
+ GPIO168_MMC3_DAT1 | MFP_PULL_HIGH,
+ GPIO111_MMC3_DAT0 | MFP_PULL_HIGH,
+ GPIO112_MMC3_CMD | MFP_PULL_HIGH,
+ GPIO151_MMC3_CLK,
+
+ /* 5V regulator */
+ GPIO89_GPIO,
+};
+
+static struct of_dev_auxdata brownstone_auxdata_lookup[] __initdata = {
+ {}
+};
+
+static void __init brownstone_init(void)
+{
+ mfp_config(ARRAY_AND_SIZE(brownstone_pin_config));
+
+ if (of_platform_populate(NULL, of_bus_ids, brownstone_auxdata_lookup,
+ NULL) < 0)
+ BUG();
+}
+
+static const char *brownstone_dt_match[] __initdata = {
+ "mrvl,mmp2-brownstone",
+ NULL,
+};
+
+#ifdef CONFIG_CPU_MMP2
+MACHINE_START(BROWNSTONE, "Brownstone Development Platform")
+ .map_io = mmp_map_io,
+ .init_irq = mmp_init_intc,
+ .timer = &mmp2_timer,
+ .init_machine = brownstone_init,
+ .dt_compat = brownstone_dt_match,
+MACHINE_END
+#endif
--
1.5.6.5
More information about the linux-arm-kernel
mailing list