[PATCH v2 1/2] serial/imx: get rid of the uses of cpu_is_mx1()
Shawn Guo
shawn.guo at linaro.org
Tue Jul 5 11:05:37 EDT 2011
The patch removes all the uses of cpu_is_mx1(). Instead, it uses
the .id_table of platform_driver to distinguish the uart device type.
A couple of !cpu_is_mx1() logic gets turned into IS_IMX_UART, as the
codes wrapped there are really IMX specific.
It also removes macro MX1_UCR3_REF25 and MX1_UCR3_REF30 which are
not used anywhere.
Signed-off-by: Shawn Guo <shawn.guo at linaro.org>
Cc: Sascha Hauer <s.hauer at pengutronix.de>
Cc: Alan Cox <alan at lxorguk.ukuu.org.uk>
---
arch/arm/mach-imx/clock-imx1.c | 6 +-
arch/arm/plat-mxc/devices/platform-imx-uart.c | 2 +-
drivers/tty/serial/imx.c | 65 ++++++++++++++++++++-----
3 files changed, 56 insertions(+), 17 deletions(-)
diff --git a/arch/arm/mach-imx/clock-imx1.c b/arch/arm/mach-imx/clock-imx1.c
index dcc4172..4aabeb2 100644
--- a/arch/arm/mach-imx/clock-imx1.c
+++ b/arch/arm/mach-imx/clock-imx1.c
@@ -587,9 +587,9 @@ static struct clk_lookup lookups[] __initdata = {
_REGISTER_CLOCK(NULL, "mma", mma_clk)
_REGISTER_CLOCK("imx_udc.0", NULL, usbd_clk)
_REGISTER_CLOCK(NULL, "gpt", gpt_clk)
- _REGISTER_CLOCK("imx-uart.0", NULL, uart_clk)
- _REGISTER_CLOCK("imx-uart.1", NULL, uart_clk)
- _REGISTER_CLOCK("imx-uart.2", NULL, uart_clk)
+ _REGISTER_CLOCK("imx1-uart.0", NULL, uart_clk)
+ _REGISTER_CLOCK("imx1-uart.1", NULL, uart_clk)
+ _REGISTER_CLOCK("imx1-uart.2", NULL, uart_clk)
_REGISTER_CLOCK("imx-i2c.0", NULL, i2c_clk)
_REGISTER_CLOCK("imx1-cspi.0", NULL, spi_clk)
_REGISTER_CLOCK("imx1-cspi.1", NULL, spi_clk)
diff --git a/arch/arm/plat-mxc/devices/platform-imx-uart.c b/arch/arm/plat-mxc/devices/platform-imx-uart.c
index cfce8c9..477271a 100644
--- a/arch/arm/plat-mxc/devices/platform-imx-uart.c
+++ b/arch/arm/plat-mxc/devices/platform-imx-uart.c
@@ -152,7 +152,7 @@ struct platform_device *__init imx_add_imx_uart_3irq(
},
};
- return imx_add_platform_device("imx-uart", data->id, res,
+ return imx_add_platform_device("imx1-uart", data->id, res,
ARRAY_SIZE(res), pdata, sizeof(*pdata));
}
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 22fe801..ddebb5c 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -48,7 +48,6 @@
#include <asm/io.h>
#include <asm/irq.h>
-#include <mach/hardware.h>
#include <mach/imx-uart.h>
/* Register definitions */
@@ -66,8 +65,9 @@
#define UBIR 0xa4 /* BRM Incremental Register */
#define UBMR 0xa8 /* BRM Modulator Register */
#define UBRC 0xac /* Baud Rate Count Register */
-#define MX2_ONEMS 0xb0 /* One Millisecond register */
-#define UTS (cpu_is_mx1() ? 0xd0 : 0xb4) /* UART Test Register */
+#define IMX_ONEMS 0xb0 /* One Millisecond register */
+#define IMX1_UTS 0xd0 /* UART Test Register on i.mx1 */
+#define IMX_UTS 0xb4 /* UART Test Register on all other i.mx*/
/* UART Control Register Bit Fields.*/
#define URXD_CHARRDY (1<<15)
@@ -87,7 +87,7 @@
#define UCR1_RTSDEN (1<<5) /* RTS delta interrupt enable */
#define UCR1_SNDBRK (1<<4) /* Send break */
#define UCR1_TDMAEN (1<<3) /* Transmitter ready DMA enable */
-#define MX1_UCR1_UARTCLKEN (1<<2) /* UART clock enabled, mx1 only */
+#define IMX1_UCR1_UARTCLKEN (1<<2) /* UART clock enabled, i.mx1 only */
#define UCR1_DOZE (1<<1) /* Doze */
#define UCR1_UARTEN (1<<0) /* UART enabled */
#define UCR2_ESCI (1<<15) /* Escape seq interrupt enable */
@@ -113,9 +113,7 @@
#define UCR3_RXDSEN (1<<6) /* Receive status interrupt enable */
#define UCR3_AIRINTEN (1<<5) /* Async IR wake interrupt enable */
#define UCR3_AWAKEN (1<<4) /* Async wake interrupt enable */
-#define MX1_UCR3_REF25 (1<<3) /* Ref freq 25 MHz, only on mx1 */
-#define MX1_UCR3_REF30 (1<<2) /* Ref Freq 30 MHz, only on mx1 */
-#define MX2_UCR3_RXDMUXSEL (1<<2) /* RXD Muxed Input Select, on mx2/mx3 */
+#define IMX_UCR3_RXDMUXSEL (1<<2) /* RXD Muxed Input Select */
#define UCR3_INVT (1<<1) /* Inverted Infrared transmission */
#define UCR3_BPEN (1<<0) /* Preset registers enable */
#define UCR4_CTSTL_SHF 10 /* CTS trigger level shift */
@@ -181,6 +179,17 @@
#define UART_NR 8
+enum imx_uart_type {
+ IMX1_UART,
+ IMX_UART,
+};
+
+/* device type dependent stuff */
+struct imx_uart_data {
+ unsigned uts_reg;
+ enum imx_uart_type devtype;
+};
+
struct imx_port {
struct uart_port port;
struct timer_list timer;
@@ -192,6 +201,7 @@ struct imx_port {
unsigned int irda_inv_tx:1;
unsigned short trcv_delay; /* transceiver delay */
struct clk *clk;
+ struct imx_uart_data *devdata;
};
#ifdef CONFIG_IRDA
@@ -200,6 +210,33 @@ struct imx_port {
#define USE_IRDA(sport) (0)
#endif
+#define UTS (sport->devdata->uts_reg)
+#define IS_IMX1_UART() (sport->devdata->devtype == IMX1_UART)
+#define IS_IMX_UART() (sport->devdata->devtype == IMX_UART)
+
+static struct imx_uart_data imx_uart_devdata[] = {
+ [IMX1_UART] = {
+ .uts_reg = IMX1_UTS,
+ .devtype = IMX1_UART,
+ },
+ [IMX_UART] = {
+ .uts_reg = IMX_UTS,
+ .devtype = IMX_UART,
+ },
+};
+
+static struct platform_device_id imx_uart_devtype[] = {
+ {
+ .name = "imx1-uart",
+ .driver_data = (kernel_ulong_t) &imx_uart_devdata[IMX1_UART],
+ }, {
+ .name = "imx-uart",
+ .driver_data = (kernel_ulong_t) &imx_uart_devdata[IMX_UART],
+ }, {
+ /* sentinel */
+ }
+};
+
/*
* Handle any change of modem status signal since we were last called.
*/
@@ -689,9 +726,9 @@ static int imx_startup(struct uart_port *port)
}
}
- if (!cpu_is_mx1()) {
+ if (IS_IMX_UART()) {
temp = readl(sport->port.membase + UCR3);
- temp |= MX2_UCR3_RXDMUXSEL;
+ temp |= IMX_UCR3_RXDMUXSEL;
writel(temp, sport->port.membase + UCR3);
}
@@ -923,9 +960,9 @@ imx_set_termios(struct uart_port *port, struct ktermios *termios,
writel(num, sport->port.membase + UBIR);
writel(denom, sport->port.membase + UBMR);
- if (!cpu_is_mx1())
+ if (IS_IMX_UART())
writel(sport->port.uartclk / div / 1000,
- sport->port.membase + MX2_ONEMS);
+ sport->port.membase + IMX_ONEMS);
writel(old_ucr1, sport->port.membase + UCR1);
@@ -1062,8 +1099,8 @@ imx_console_write(struct console *co, const char *s, unsigned int count)
ucr1 = old_ucr1 = readl(sport->port.membase + UCR1);
old_ucr2 = readl(sport->port.membase + UCR2);
- if (cpu_is_mx1())
- ucr1 |= MX1_UCR1_UARTCLKEN;
+ if (IS_IMX1_UART())
+ ucr1 |= IMX1_UCR1_UARTCLKEN;
ucr1 |= UCR1_UARTEN;
ucr1 &= ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN);
@@ -1262,6 +1299,7 @@ static int serial_imx_probe(struct platform_device *pdev)
init_timer(&sport->timer);
sport->timer.function = imx_timeout;
sport->timer.data = (unsigned long)sport;
+ sport->devdata = (struct imx_uart_data *) pdev->id_entry->driver_data;
sport->clk = clk_get(&pdev->dev, "uart");
if (IS_ERR(sport->clk)) {
@@ -1340,6 +1378,7 @@ static struct platform_driver serial_imx_driver = {
.suspend = serial_imx_suspend,
.resume = serial_imx_resume,
+ .id_table = imx_uart_devtype,
.driver = {
.name = "imx-uart",
.owner = THIS_MODULE,
--
1.7.4.1
More information about the linux-arm-kernel
mailing list