[PATCH 3/3] ARM: pxa168/teton bga: add board support for i2c and rtc-ds1337

[Marek Vasut]

Dne St 8. září 2010 19:05:02 Mark F. Brown napsal(a):
> On Wed, Sep 8, 2010 at 11:54 AM, Marek Vasut <marek.vasut at gmail.com> wrote:
> > Dne St 8. září 2010 07:34:24 Haojian Zhuang napsal(a):
> >> On Wed, Sep 8, 2010 at 10:56 AM, Mark F. Brown <mark.brown314 at gmail.com>
> > 
> > wrote:
> >> > Signed-off-by: Mark F. Brown <mark.brown314 at gmail.com>
> >> > ---
> >> >  arch/arm/mach-mmp/teton_bga.c |   10 ++++++++++
> >> >  1 files changed, 10 insertions(+), 0 deletions(-)
> >> > 
> >> > diff --git a/arch/arm/mach-mmp/teton_bga.c
> >> > b/arch/arm/mach-mmp/teton_bga.c index bbeda5c..8e5801c 100644
> >> > --- a/arch/arm/mach-mmp/teton_bga.c
> >> > +++ b/arch/arm/mach-mmp/teton_bga.c
> >> > @@ -22,6 +22,7 @@
> >> >  #include <mach/gpio.h>
> >> >  #include <linux/input.h>
> >> >  #include <plat/pxa27x_keypad.h>
> >> > +#include <linux/i2c.h>
> >> > 
> >> >  #include "common.h"
> >> > 
> >> > @@ -35,6 +36,10 @@ static unsigned long teton_bga_pin_config[]
> >> > __initdata = { GPIO110_KP_MKIN0,
> >> >        GPIO111_KP_MKOUT7,
> >> >        GPIO112_KP_MKOUT6,
> >> > +
> >> > +       /* i2c bus */
> >> > +       GPIO105_CI2C_SDA,
> >> > +       GPIO106_CI2C_SCL,
> >> >  };
> >> > 
> >> >  static unsigned int teton_bga_matrix_key_map[] = {
> >> > @@ -52,6 +57,10 @@ static struct pxa27x_keypad_platform_data
> >> > teton_bga_keypad_info __initdata = { .debounce_interval      = 30,
> >> >  };
> >> > 
> >> > +static struct i2c_board_info teton_bga_i2c_info[] __initdata = {
> >> > +       { I2C_BOARD_INFO("ds1337", 0x68), },
> >> > +};
> >> > +
> >> 
> >> I don't have the schematic of teton. But RTC chips should always has
> >> an irq pin. Is it also connected in your platform?
> > 
> > I think this one doesn't, but I haven't checked.
> > 
> > Cheers
> > 
> >> >  static void __init teton_bga_init(void)
> >> >  {
> >> >        mfp_config(ARRAY_AND_SIZE(teton_bga_pin_config));
> >> > @@ -59,6 +68,7 @@ static void __init teton_bga_init(void)
> >> >        /* on-chip devices */
> >> >        pxa168_add_uart(1);
> >> >        pxa168_add_keypad(&teton_bga_keypad_info);
> >> > +       pxa168_add_twsi(0, NULL, ARRAY_AND_SIZE(teton_bga_i2c_info));
> >> >  }
> >> > 
> >> >  MACHINE_START(TETON_BGA, "PXA168-based Teton BGA Development
> >> > Platform") --
> >> > 1.7.0.4
> >> > 
> >> > --
> >> > To unsubscribe from this list: send the line "unsubscribe
> >> > linux-kernel" in the body of a message to majordomo at vger.kernel.org
> >> > More majordomo info at  http://vger.kernel.org/majordomo-info.html
> >> > Please read the FAQ at  http://www.tux.org/lkml/
> >> 
> >> _______________________________________________
> >> linux-arm-kernel mailing list
> >> linux-arm-kernel at lists.infradead.org
> >> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> 
> It actually does have an alarm pin and it is connected as well. I did
> not include it, because I have not tested the alarm functionality yet.
> I was going to add it in a later patch. I did test the hardware clock
> to system clock syncing.

Fix the CC please. And be careful not to screw this up again next time.

Please add the alarm pin too. Thanks

Cheers
> 
> Regards,
> -- Mark