[PATCH 1/1] net: phy: meson-gxl: Add generic dummy stubs for MMD register access
Chris Healy
cphealy at gmail.com
Sun Jan 29 13:25:59 PST 2023
On Sun, Jan 29, 2023 at 2:26 AM Heiner Kallweit <hkallweit1 at gmail.com> wrote:
>
> On 29.01.2023 03:26, Chris Healy wrote:
> > From: Chris Healy <healych at amazon.com>
> >
> Hi Chris,
>
> > The Meson G12A Internal PHY does not support standard IEEE MMD extended
> > register access, therefore add generic dummy stubs to fail the read and
> > write MMD calls. This is necessary to prevent the core PHY code from
> > erroneously believing that EEE is supported by this PHY even though this
> > PHY does not support EEE, as MMD register access returns all FFFFs.
> >
> > Signed-off-by: Chris Healy <healych at amazon.com>
> > ---
> > drivers/net/phy/meson-gxl.c | 2 ++
> > 1 file changed, 2 insertions(+)
> >
> > diff --git a/drivers/net/phy/meson-gxl.c b/drivers/net/phy/meson-gxl.c
> > index c49062ad72c6..5e41658b1e2f 100644
> > --- a/drivers/net/phy/meson-gxl.c
> > +++ b/drivers/net/phy/meson-gxl.c
> > @@ -271,6 +271,8 @@ static struct phy_driver meson_gxl_phy[] = {
> > .handle_interrupt = meson_gxl_handle_interrupt,
> > .suspend = genphy_suspend,
> > .resume = genphy_resume,
> > + .read_mmd = genphy_read_mmd_unsupported,
> > + .write_mmd = genphy_write_mmd_unsupported,
> > },
> > };
> >
>
> thanks for catching this. The same issue we may have for the GXL-internal PHY.
> Did you check this?
I do not have HW with GXL-internal PHY so I cannot test it and don't
feel comfortable making the change for that PHY ID without someone
providing the necessary feedback. If someone can confirm the same all
FFFFs with the MMD registers, I'd be happy to add the read/write MMD
callbacks for that PHY in v2.
>
> One result of the issue is the invalid ethtool --show-eee output given below.
> Therefore the patch should go to stable, please annotate it as [PATCH net].
>
> Fixes tag should be:
> 5c3407abb338 ("net: phy: meson-gxl: add g12a support")
Yep, looking at the ethtool --show-eee output is what got me looking
at this in the first place. I was hoping to enable EEE... ;-)
I'll add the fixes tag in v2.
>
>
> EEE settings for eth0:
> EEE status: enabled - active
> Tx LPI: 1000000 (us)
> Supported EEE link modes: 100baseT/Full
> 1000baseT/Full
> 10000baseT/Full
> 1000baseKX/Full
> 10000baseKX4/Full
> 10000baseKR/Full
> Advertised EEE link modes: 100baseT/Full
> 1000baseT/Full
> 10000baseT/Full
> 1000baseKX/Full
> 10000baseKX4/Full
> 10000baseKR/Full
> Link partner advertised EEE link modes: 100baseT/Full
> 1000baseT/Full
> 10000baseT/Full
> 1000baseKX/Full
> 10000baseKX4/Full
> 10000baseKR/Full
>
More information about the linux-amlogic
mailing list