[PATCH net-next] net: phy: meson-gxl: support more G12A-internal PHY versions

Heiner Kallweit hkallweit1 at gmail.com
Sun Jan 15 12:38:06 PST 2023


On 15.01.2023 19:43, Neil Armstrong wrote:
> Hi Heiner,
> 
> Le 15/01/2023 à 18:09, Heiner Kallweit a écrit :
>> On 15.01.2023 17:57, Andrew Lunn wrote:
>>> On Sun, Jan 15, 2023 at 04:19:37PM +0100, Heiner Kallweit wrote:
>>>> On my SC2-based system the genphy driver was used because the PHY
>>>> identifies as 0x01803300. It works normal with the meson g12a
>>>> driver after this change.
>>>> Switch to PHY_ID_MATCH_MODEL to cover the different sub-versions.
>>>
>>> Hi Heiner
>>>
>>> Are there any datasheets for these devices? Anything which documents
>>> the lower nibble really is a revision?
>>>
>>> I'm just trying to avoid future problems where we find it is actually
>>> a different PHY, needs its own MATCH_EXACT entry, and then we find we
>>> break devices using 0x01803302 which we had no idea exists, but got
>>> covered by this change.
>>>
>> The SC2 platform inherited a lot from G12A, therefore it's plausible
>> that it's the same PHY. Also the vendor driver for SC2 gives a hint
>> as it has the following compatible for the PHY:
>>
>> compatible = "ethernet-phy-id0180.3301", "ethernet-phy-ieee802.3-c22";
>>
>> But you're right, I can't say for sure as I don't have the datasheets.
> 
> On G12A (& GXL), the PHY ID is set in the MDIO MUX registers,
> please see:
> https://elixir.bootlin.com/linux/latest/source/drivers/net/mdio/mdio-mux-meson-g12a.c#L36
> 
> So you should either add support for the PHY mux in SC2 or check
> what is in the ETH_PHY_CNTL0 register.
> 
Thanks for the hint. I just checked and reading back ETH_PHY_CNTL0 at the
end of g12a_enable_internal_mdio() gives me the expected result of 0x33010180.
But still the PHY reports 3300.
Even if I write some other random value to ETH_PHY_CNTL0, I get 0180/3300
as PHY ID.

For u-boot I found the following:

https://github.com/khadas/u-boot/blob/khadas-vim4-r-64bit/drivers/net/phy/amlogic.c

static struct phy_driver amlogic_internal_driver = {
	.name = "Meson GXL Internal PHY",
	.uid = 0x01803300,
	.mask = 0xfffffff0,
	.features = PHY_BASIC_FEATURES,
	.config = &meson_phy_config,
	.startup = &meson_aml_startup,
	.shutdown = &genphy_shutdown,
};

So it's the same PHY ID I'm seeing in Linux.

My best guess is that the following is the case:

The PHY compatible string in DT is the following in all cases:
compatible = "ethernet-phy-id0180.3301", "ethernet-phy-ieee802.3-c22";

Therefore id 0180/3301 is used even if the PHY reports something else.
Means it doesn't matter which value you write to ETH_PHY_CNTL0.

I reduced the compatible string to compatible = "ethernet-phy-ieee802.3-c22"
and this resulted in the actual PHY ID being used.
You could change the compatible in dts the same way for any g12a system
and I assume you would get 0180/3300 too.

Remaining question is why the value in ETH_PHY_CNTL0 is ignored.

> Neil
> 
>>
>>>     Andrew
>>
>> Heiner
> 




More information about the linux-amlogic mailing list