[openwrt/openwrt] ramips: Add support for SERCOMM NA502
LEDE Commits
lede-commits at lists.infradead.org
Thu Jun 10 08:14:31 PDT 2021
ynezz pushed a commit to openwrt/openwrt.git, branch openwrt-21.02:
https://git.openwrt.org/46b53ce83b3d47ef48a0ef9cb3263a038e1ebc8a
commit 46b53ce83b3d47ef48a0ef9cb3263a038e1ebc8a
Author: Andreas Böhler <dev at aboehler.at>
AuthorDate: Mon Mar 15 00:07:17 2021 +0100
ramips: Add support for SERCOMM NA502
The SERCOMM NA502 is a smart home gateway manufactured by SERCOMM and sold
under different brands (among others, A1 Telekom Austria SmartHome
Gateway). It has multi-protocol radio support in addition to LAN and WiFi.
Note: BLE is currently unsupported.
Specifications
--------------
- MT7621ST 880MHz, Single-Core, Dual-Thread
- MT7603EN 2.4GHz WiFi
- MT7662EN 5GHz WiFi + BLE
- 128MiB NAND
- 256MiB DDR3 RAM
- SD3503 ZWave Controller
- EM357 Zigbee Coordinator
MAC address assignment
----------------------
LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches
the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the
OEM firmware does not enable 5GHz WiFi.
Installation
------------
Attach serial console, then boot the initramfs image via TFTP.
Once inside OpenWrt, run sysupgrade -n with the sysupgrade file.
Attention: The device has a dual-firmware design. We overwrite kernel2,
since kernel1 contains an automatic recovery image.
If you get NAND ECC errors and are stuck with bad eraseblocks, try to
erase the mtd partition first with
mtd unlock ubi
mtd erase ubi
This should only be needed once.
Signed-off-by: Andreas Böhler <dev at aboehler.at>
[use kiB for IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk at adrianschmutzler.de>
(cherry picked from commit a3d8c1295ed9eeceabd78ab86e73b151ae2868a9)
---
target/linux/ramips/dts/mt7621_sercomm_na502.dts | 212 +++++++++++++++++++++
target/linux/ramips/image/mt7621.mk | 14 ++
.../mt7621/base-files/etc/board.d/02_network | 1 +
.../mt7621/base-files/lib/upgrade/platform.sh | 1 +
4 files changed, 228 insertions(+)
diff --git a/target/linux/ramips/dts/mt7621_sercomm_na502.dts b/target/linux/ramips/dts/mt7621_sercomm_na502.dts
new file mode 100644
index 0000000000..af55d1058f
--- /dev/null
+++ b/target/linux/ramips/dts/mt7621_sercomm_na502.dts
@@ -0,0 +1,212 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "sercomm,na502", "mediatek,mt7621-soc";
+ model = "SERCOMM NA502";
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "green:power";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ };
+
+ internet {
+ label = "green:internet";
+ gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi {
+ label = "green:wifi";
+ gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ zwave {
+ label = "green:zwave";
+ gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
+ };
+
+ service {
+ label = "green:service";
+ gpios = <&gpio 26 GPIO_ACTIVE_LOW>;
+ };
+
+ zigbee {
+ label = "green:zigbee";
+ gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
+ };
+
+ bluetooth {
+ label = "green:bluetooth";
+ gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ select {
+ label = "select";
+ gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_0>;
+ };
+
+ sync {
+ label = "sync";
+ gpios = <&gpio 32 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ };
+ };
+
+ gpio-export {
+ compatible = "gpio-export";
+
+ zwave_reset {
+ gpio-export,name = "zwave_reset";
+ gpio-export,output = <1>;
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ zigbee_reset {
+ gpio-export,name = "zigbee_reset";
+ gpio-export,output = <1>;
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&gmac0 {
+ mtd-mac-address = <&factory 0xe000>;
+};
+
+&nand {
+ status = "okay";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ partition at 80000 {
+ label = "config";
+ reg = <0x80000 0x80000>;
+ read-only;
+ };
+
+ factory: partition at 100000 {
+ label = "factory";
+ reg = <0x100000 0x40000>;
+ };
+
+ partition at 140000 {
+ label = "kernel1";
+ reg = <0x140000 0x1400000>;
+ };
+
+ partition at 1540000 {
+ label = "kernel";
+ reg = <0x1540000 0x400000>;
+ };
+
+ partition at 1940000 {
+ label = "ubi";
+ reg = <0x1940000 0x1000000>;
+ };
+
+ partition at 2940000 {
+ label = "user_storage";
+ reg = <0x2940000 0x100000>;
+ };
+
+ partition at 2a40000 {
+ label = "data";
+ reg = <0x2a40000 0x1000000>;
+ };
+
+ partition at 3a40000 {
+ label = "storage";
+ reg = <0x3a40000 0x3200000>;
+ };
+
+ partition at 6c40000 {
+ label = "backup";
+ reg = <0x6c40000 0x1340000>;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pcie0 {
+ wifi at 0,0 {
+ compatible = "mediatek,mt76";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x8000>;
+ mtd-mac-address = <&factory 0xe000>;
+ mtd-mac-address-increment = <1>;
+ ieee80211-freq-limit = <5000000 6000000>;
+ };
+};
+
+&pcie1 {
+ wifi at 0,0 {
+ compatible = "mediatek,mt76";
+ reg = <0x0 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x0000>;
+ mtd-mac-address = <&factory 0xe000>;
+ mtd-mac-address-increment = <2>;
+ ieee80211-freq-limit = <2400000 2500000>;
+ };
+};
+
+&state_default {
+ gpio {
+ groups = "jtag", "rgmii2";
+ function = "gpio";
+ };
+};
+
+&switch0 {
+ ports {
+ port at 4 {
+ status = "okay";
+ label = "lan";
+ };
+ };
+};
+
+&uartlite2 {
+ status = "okay";
+};
+
+&uartlite3 {
+ status = "okay";
+};
diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk
index 6645c7b06e..a3bc14d59d 100644
--- a/target/linux/ramips/image/mt7621.mk
+++ b/target/linux/ramips/image/mt7621.mk
@@ -1167,6 +1167,20 @@ define Device/samknows_whitebox-v8
endef
TARGET_DEVICES += samknows_whitebox-v8
+define Device/sercomm_na502
+ $(Device/uimage-lzma-loader)
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ IMAGE_SIZE := 20480k
+ IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+ UBINIZE_OPTS := -E 5
+ KERNEL_SIZE := 4096k
+ DEVICE_VENDOR := SERCOMM
+ DEVICE_MODEL := NA502
+ DEVICE_PACKAGES := kmod-mt76x2 kmod-mt7603 kmod-usb3
+endef
+TARGET_DEVICES += sercomm_na502
+
define Device/storylink_sap-g3200u3
$(Device/dsa-migration)
IMAGE_SIZE := 7872k
diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
index c0c767306a..4b44669b84 100755
--- a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
@@ -13,6 +13,7 @@ ramips_setup_interfaces()
edimax,re23s|\
mikrotik,routerboard-m11g|\
netgear,ex6150|\
+ sercomm,na502|\
thunder,timecloud|\
tplink,re350-v1|\
tplink,re500-v1|\
diff --git a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
index 4943ad1305..c2ad4d3ed6 100755
--- a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
@@ -72,6 +72,7 @@ platform_do_upgrade() {
netgear,wac104|\
netgear,wac124|\
netis,wf2881|\
+ sercomm,na502|\
xiaomi,mi-router-3g|\
xiaomi,mi-router-3-pro|\
xiaomi,mi-router-4|\
More information about the lede-commits
mailing list