[openwrt/openwrt] ath79: add support for NEC Aterm WF1200CR
LEDE Commits
lede-commits at lists.infradead.org
Sun Jun 6 12:38:53 PDT 2021
adrian pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/a4e2766a5bfa1ac1c706d1cd58c6706ffdcde895
commit a4e2766a5bfa1ac1c706d1cd58c6706ffdcde895
Author: INAGAKI Hiroshi <musashino.open at gmail.com>
AuthorDate: Thu Mar 25 00:19:59 2021 +0900
ath79: add support for NEC Aterm WF1200CR
NEC Aterm WF1200CR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
QCA9561.
Specification:
- SoC : Qualcomm Atheros QCA9561
- RAM : DDR2 128 MiB (W971GG6SB-25)
- Flash : SPI-NOR 8 MiB (MX25L6433FM2I-08G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : QCA9561 (SoC)
- 5 GHz : QCA9888
- Ethernet : 2x 10/100 Mbps
- Switch : QCA9561 (SoC)
- LEDs/Keys : 8x/3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- JP1: Vcc, GND, NC, TX, RX from "JP1" marking
- 115200n8
- Power : 12 VDC, 0.9 A
Flash instruction using factory image (stock: < v1.3.2):
1. Boot WF1200CR normally with "Router" mode
2. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click update ("更新") button to
perform firmware update
4. Wait ~150 seconds to complete flashing
Alternate flash instruction using initramfs image (stock: >= v1.3.2):
1. Prepare the TFTP server with the IP address 192.168.1.10 and place
the OpenWrt initramfs image to the TFTP directory with the name
"0101A8C0.img"
2. Connect serial console to WF1200CR
3. Boot WF1200CR and interrupt with any key after the message
"Hit any key to stop autoboot: 2", the U-Boot starts telnetd after
the message "starting telnetd server from server 192.168.1.1"
4. login the telnet (address: 192.168.1.1)
5. Perform the following commands to modify "bootcmd" variable
temporary and check the value
(to ignore the limitation of available commands, "tp; " command at
the first is required as dummy, and the output of "printenv" is
printed on the serial console)
tp; set bootcmd 'set autostart yes; tftpboot'
tp; printenv
6. Save the modified variable with the following command and reset
device
tp; saveenv
tp; reset
7. The U-Boot downloads initramfs image from TFTP server and boots it
8. On initramfs image, download the sysupgrade image to the device and
perform the following commands to erase stock firmware and sysupgrade
mtd erase firmware
sysupgrade <sysupgrade image>
9. After the rebooting by completion of sysupgrade, start U-Boot telnetd
and login with the same way above (3, 4)
10. Perform the following commands to reset "bootcmd" variable to the
default and reset the device
tp; run seattle
tp; reset
(the contents of "seattle":
setenv bootcmd 'bootm 0x9f070040' && saveenv)
11. Wait booting-up the device
Known issues:
- the following 6x LEDs are connected to the gpio controller on QCA9888
chip and the implementation of control via the controller is missing in
ath10k/ath10k-ct
- "ACTIVE" (Red/Green)
- "2.4GHz" (Red/Green)
- "5GHz" (Red/Green)
Note:
- after the version v1.3.2 of stock firmware, "offline update" by
uploading image by user is deleted and the factory image cannot be
used
- the U-Boot on WF1200CR doesn't configure the port-side LEDs on WAN/LAN
and the configuration is required on OpenWrt
- gpio-hog: set the direction of GPIO 14(WAN)/19(LAN) to output
- pinmux: set GPIO 14/19 as switch-controlled LEDs
Signed-off-by: INAGAKI Hiroshi <musashino.open at gmail.com>
---
target/linux/ath79/dts/qca9561_nec_wf1200cr.dts | 166 +++++++++++++++++++++
.../generic/base-files/etc/board.d/02_network | 6 +
.../etc/hotplug.d/firmware/10-ath9k-eeprom | 1 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 1 +
target/linux/ath79/image/generic.mk | 27 +++-
5 files changed, 196 insertions(+), 5 deletions(-)
diff --git a/target/linux/ath79/dts/qca9561_nec_wf1200cr.dts b/target/linux/ath79/dts/qca9561_nec_wf1200cr.dts
new file mode 100644
index 0000000000..90aac30d7f
--- /dev/null
+++ b/target/linux/ath79/dts/qca9561_nec_wf1200cr.dts
@@ -0,0 +1,166 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca956x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "NEC Aterm WF1200CR";
+ compatible = "nec,wf1200cr", "qca,qca9561";
+
+ aliases {
+ led-boot = &led_power_green;
+ led-failsafe = &led_power_red;
+ led-running = &led_power_green;
+ led-upgrade = &led_power_green;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ /* other LEDs are connected to ath10k (QCA9888) gpiochip */
+
+ led_power_green: power_green {
+ label = "green:power";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+
+ led_power_red: power_red {
+ label = "red:power";
+ gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ debounce-interval = <60>;
+ };
+
+ router {
+ label = "rt";
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_0>;
+ linux,input-type = <EV_SW>;
+ debounce-interval = <60>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ debounce-interval = <60>;
+ };
+ };
+};
+
+&spi {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "devdata";
+ reg = <0x040000 0x010000>;
+ read-only;
+ };
+
+ partition at 50000 {
+ label = "devconf";
+ reg = <0x050000 0x010000>;
+ read-only;
+ };
+
+ partition at 60000 {
+ label = "misc";
+ reg = <0x060000 0x010000>;
+ read-only;
+ };
+
+ partition at 70000 {
+ compatible = "seama";
+ label = "firmware";
+ reg = <0x070000 0x780000>;
+ };
+
+ partition at 7f0000 {
+ label = "art";
+ reg = <0x7f0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ pll-data = <0x03000101 0x00000101 0x00001919>;
+
+ phy-handle = <&swphy0>;
+
+ gmac-config {
+ device = <&gmac>;
+
+ switch-phy-swap = <1>;
+ switch-phy-addr-swap = <0>;
+ };
+};
+
+ð1 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinmux_swled_enable_pins>;
+};
+
+&gpio {
+ switch_leds {
+ gpio-hog;
+ gpios = <14 GPIO_ACTIVE_HIGH>, /* WAN */
+ <19 GPIO_ACTIVE_HIGH>; /* LAN */
+ output-high;
+ line-name = "led:wan-lan";
+ };
+};
+
+&pinmux {
+ pinmux_swled_enable_pins: swled_enable_pins {
+ pinctrl-single,bits =
+ <0xc 0x240000 0xff0000>, /* WAN */
+ <0x10 0x10000000 0xff000000>; /* LAN */
+ };
+};
+
+&pcie {
+ status = "okay";
+
+ wifi at 0,0 {
+ compatible = "qcom,ath10k";
+ reg = <0x0000 0 0 0 0>;
+ };
+};
+
+&wmac {
+ status = "okay";
+
+ qca,no-eeprom;
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index ffafe7db20..f07c086977 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -300,6 +300,11 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0 at eth0" "2:lan:1" "3:lan:2" "4:lan:3" "5:lan:4" "1:wan"
;;
+ nec,wf1200cr)
+ ucidef_set_interface_wan "eth1"
+ ucidef_add_switch "switch0" \
+ "0 at eth0" "1:lan"
+ ;;
nec,wg1200cr|\
qxwlan,e1700ac-v2-8m|\
qxwlan,e1700ac-v2-16m|\
@@ -599,6 +604,7 @@ ath79_setup_macs()
base_mac=$(mtd_get_mac_binary u-boot 0x1fc00)
wan_mac=$(macaddr_add "$base_mac" 1)
;;
+ nec,wf1200cr|\
nec,wg1200cr)
lan_mac=$(mtd_get_mac_ascii devdata "lanmac")
wan_mac=$(mtd_get_mac_ascii devdata "wanmac")
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index 62f2f1e8b4..388f477856 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -32,6 +32,7 @@ case "$FIRMWARE" in
dlink,dir-842-c2|\
dlink,dir-842-c3|\
dlink,dir-859-a1|\
+ nec,wf1200cr|\
nec,wg1200cr|\
wd,mynet-n750)
caldata_extract "art" 0x1000 0x440
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index b2392c2c64..feb9a5186e 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -201,6 +201,7 @@ case "$FIRMWARE" in
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
+ nec,wf1200cr|\
nec,wg1200cr)
caldata_extract "art" 0x5000 0x2f20
ath10k_patch_mac $(mtd_get_mac_ascii devdata wlan5mac)
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index b459136ef5..9d0be2b86b 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -1417,20 +1417,37 @@ define Device/mercury_mw4530r-v1
endef
TARGET_DEVICES += mercury_mw4530r-v1
+define Device/nec_wx1200cr
+ DEVICE_VENDOR := NEC
+ IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
+ IMAGE/sysupgrade.bin := $$(IMAGE/default) | seama | pad-rootfs | \
+ append-metadata | check-size
+ DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
+endef
+
+define Device/nec_wf1200cr
+ $(Device/nec_wx1200cr)
+ SOC := qca9561
+ DEVICE_MODEL := Aterm WF1200CR
+ IMAGE_SIZE := 7680k
+ SEAMA_MTDBLOCK := 5
+ SEAMA_SIGNATURE := wrgac62_necpf.2016gui_wf1200cr
+ IMAGES += factory.bin
+ IMAGE/factory.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \
+ seama-seal | nec-enc ryztfyutcrqqo69d | check-size
+endef
+TARGET_DEVICES += nec_wf1200cr
+
define Device/nec_wg1200cr
+ $(Device/nec_wx1200cr)
SOC := qca9563
- DEVICE_VENDOR := NEC
DEVICE_MODEL := Aterm WG1200CR
IMAGE_SIZE := 7616k
SEAMA_MTDBLOCK := 6
SEAMA_SIGNATURE := wrgac72_necpf.2016gui_wg1200cr
IMAGES += factory.bin
- IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
- IMAGE/sysupgrade.bin := $$(IMAGE/default) | seama | pad-rootfs | \
- append-metadata | check-size
IMAGE/factory.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \
seama-seal | nec-enc 9gsiy9nzep452pad | check-size
- DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
endef
TARGET_DEVICES += nec_wg1200cr
More information about the lede-commits
mailing list