MAC port 0 enabling failed

[Thomas Schreiner]

Hello list,
I encountered a strange problem while setting up my Senao SL-2011CD PCMCIA card (Prism 2.5) with hostap-0.0.4.
While the orinoco_cs driver works perfectly (except from the fact I want it to register the device wlan0 but it actually registers eth1, but I don't mind and I don't know how to change this anyway), the hostap driver doesn't register the device wlan0 (even though all modules are loaded as I can see from lsmod) and dmesg says the following:

$ dmesg
ostap_crypt: registered algorithm 'NULL'
hostap_cs: 0.0.4 - 2003-07-27 (Jouni Malinen <jkmaline at cc.hut.fi>)
hostap_cs: setting Vcc=33 (constant)
hostap_cs: CS_EVENT_CARD_INSERTION
prism2_config()
hostap_cs: setting Vcc=33 (from config)
Checking CFTABLE_ENTRY 0x01 (default 0x01)
IO window settings: cfg->io.nwin=1 dflt.io.nwin=1
io->flags = 0x0046, io.base=0x0000, len=64
hostap_cs: index 0x01: Vcc 3.3, irq 3, io 0x0180-0x01bf
hostap_cs: Registered netdevice wlan0
prism2_hw_init()
prism2_hw_init: initialized in 205 ms
wlan0: prism2_open
wlan0: hfa384x_cmd: entry still in list? (entry=c6be58b0, type=0, res=0)
wlan0: hfa384x_cmd: command was not completed (res=0, entry=c6be58b0, type=0, cmd=0x0021, param0=0xfd0b, EVSTAT=8010 INTEN=0010)
wlan0: interrupt delivery does not seem to work
wlan0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd0b, len=8)
Could not get RID for component NIC
wlan0: hfa384x_cmd: entry still in list? (entry=c6be59b0, type=0, res=0)
wlan0: hfa384x_cmd: command was not completed (res=0, entry=c6be59b0, type=0, cmd=0x0001, param0=0x0000, EVSTAT=8010 INTEN=0010)
wlan0: interrupt delivery does not seem to work
wlan0: MAC port 0 enabling failed
wlan0: could not enable MAC port
wlan0: prism2_close
wlan0: hfa384x_cmd: entry still in list? (entry=c6be58b0, type=0, res=0)
wlan0: hfa384x_cmd: command was not completed (res=0, entry=c6be58b0, type=0, cmd=0x0021, param0=0xfd02, EVSTAT=8010 INTEN=0010)
wlan0: interrupt delivery does not seem to work
wlan0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd02, len=8)
Could not get RID for component PRI
wlan0: hfa384x_cmd: entry still in list? (entry=c6be58b0, type=0, res=0)
wlan0: hfa384x_cmd: command was not completed (res=0, entry=c6be58b0, type=0, cmd=0x0021, param0=0xfd20, EVSTAT=8010 INTEN=0010)
wlan0: interrupt delivery does not seem to work
wlan0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd20, len=8)
Could not get RID for component STA
wlan0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wlan0: hfa384x_cmd_issue - timeout - reg=0x8021
wlan0: hfa384x_cmd: entry still in list? (entry=c6be58b0, type=0, res=-1)
wlan0: hfa384x_cmd: interrupted; err=-110
wlan0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd20, len=8)
wlan0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wlan0: hfa384x_cmd_issue - timeout - reg=0x8021
wlan0: hfa384x_cmd: entry still in list? (entry=c6be58b0, type=0, res=-1)
wlan0: hfa384x_cmd: interrupted; err=-110
wlan0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fc01, len=6)
wlan0: could not get own MAC address
wlan0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wlan0: hfa384x_cmd_issue - timeout - reg=0x8000
wlan0: hfa384x_cmd: entry still in list? (entry=c6be58b0, type=0, res=-1)
wlan0: hfa384x_cmd: interrupted; err=-110
wlan0: hfa384x_set_rid: CMDCODE_ACCESS_WRITE failed (res=-110, rid=fce0, len=2)
wlan0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wlan0: hfa384x_cmd_issue - timeout - reg=0x8000
wlan0: hfa384x_cmd: entry still in list? (entry=c6be58b0, type=0, res=-1)
wlan0: hfa384x_cmd: interrupted; err=-110
wlan0: hfa384x_set_rid: CMDCODE_ACCESS_WRITE failed (res=-110, rid=fc00, len=2)
wlan0: Port type setting to 6 failed
wlan0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wlan0: hfa384x_cmd_issue - timeout - reg=0x8000
wlan0: hfa384x_cmd: entry still in list? (entry=c6be58b0, type=0, res=-1)
wlan0: hfa384x_cmd: interrupted; err=-110
wlan0: MAC port 0 enabling failed

I tried all firmware I could get at http://www.netgate.com/support/prism_firmware/ (1.1.0, 1.3.4, 1.3.6, 1.4.9 which is reported to work for many people, and 1.7.4), but the messages stay the same, sometimes "entry=" varies a bit.

Do you have an idea what's wrong? Thanks a lot in advance! Would be kind if you replied to sender as well, as I'm not on the list.

Thomas

-- 
printk("Cool stuff's happening!\n")
        2.4.3 linux/fs/jffs/intrep.c
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 189 bytes
Desc: not available
Url : http://lists.shmoo.com/pipermail/hostap/attachments/20031028/8a2cf174/attachment.pgp