[PATCH v1 1/2] arm: boards: Add support for Protonic MECIO1 board
Oleksij Rempel
o.rempel at pengutronix.de
Wed Jun 12 06:05:08 PDT 2024
From: David Jander <david at protonic.nl>
Signed-off-by: David Jander <david at protonic.nl>
---
arch/arm/boards/protonic-stm32mp1/board.c | 5 +
arch/arm/boards/protonic-stm32mp1/lowlevel.c | 15 ++
arch/arm/dts/Makefile | 3 +-
arch/arm/dts/stm32mp151-mecio1.dts | 214 +++++++++++++++++++
arch/arm/mach-stm32mp/Kconfig | 6 +-
images/Makefile.stm32mp | 1 +
6 files changed, 240 insertions(+), 4 deletions(-)
create mode 100644 arch/arm/dts/stm32mp151-mecio1.dts
diff --git a/arch/arm/boards/protonic-stm32mp1/board.c b/arch/arm/boards/protonic-stm32mp1/board.c
index 68297debab..e8f47c6849 100644
--- a/arch/arm/boards/protonic-stm32mp1/board.c
+++ b/arch/arm/boards/protonic-stm32mp1/board.c
@@ -113,10 +113,15 @@ static const struct prt_stm32_machine_data prt_stm32_prtt1c = {
.flags = PRT_STM32_BOOTSRC_SD | PRT_STM32_BOOTSRC_EMMC,
};
+static const struct prt_stm32_machine_data prt_stm32_mecio1 = {
+ .flags = PRT_STM32_BOOTSRC_SPI_NOR,
+};
+
static const struct of_device_id prt_stm32_of_match[] = {
{ .compatible = "prt,prtt1a", .data = &prt_stm32_prtt1a },
{ .compatible = "prt,prtt1c", .data = &prt_stm32_prtt1c },
{ .compatible = "prt,prtt1s", .data = &prt_stm32_prtt1a },
+ { .compatible = "prt,mecio1", .data = &prt_stm32_mecio1 },
{ /* sentinel */ },
};
BAREBOX_DEEP_PROBE_ENABLE(prt_stm32_of_match);
diff --git a/arch/arm/boards/protonic-stm32mp1/lowlevel.c b/arch/arm/boards/protonic-stm32mp1/lowlevel.c
index 2fd7f8ba8b..97d60b6ea4 100644
--- a/arch/arm/boards/protonic-stm32mp1/lowlevel.c
+++ b/arch/arm/boards/protonic-stm32mp1/lowlevel.c
@@ -8,6 +8,7 @@
extern char __dtb_z_stm32mp151_prtt1a_start[];
extern char __dtb_z_stm32mp151_prtt1c_start[];
extern char __dtb_z_stm32mp151_prtt1s_start[];
+extern char __dtb_z_stm32mp151_mecio1_start[];
static void setup_uart(void)
{
@@ -56,3 +57,17 @@ ENTRY_FUNCTION(start_prtt1s, r0, r1, r2)
stm32mp1_barebox_entry(fdt);
}
+
+ENTRY_FUNCTION(start_mecio1, r0, r1, r2)
+{
+ void *fdt;
+
+ stm32mp_cpu_lowlevel_init();
+
+ if (IS_ENABLED(CONFIG_DEBUG_LL))
+ setup_uart();
+
+ fdt = __dtb_z_stm32mp151_mecio1_start + get_runtime_offset();
+
+ stm32mp1_barebox_entry(fdt);
+}
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 40d61ce8db..37158ce0df 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -111,7 +111,8 @@ lwl-$(CONFIG_MACH_PROTONIC_MECSBC) += rk3568-mecsbc.dtb.o
lwl-$(CONFIG_MACH_PROTONIC_STM32MP1) += \
stm32mp151-prtt1a.dtb.o \
stm32mp151-prtt1c.dtb.o \
- stm32mp151-prtt1s.dtb.o
+ stm32mp151-prtt1s.dtb.o \
+ stm32mp151-mecio1.dtb.o
lwl-$(CONFIG_MACH_RADXA_ROCK) += rk3188-radxarock.dtb.o
lwl-$(CONFIG_MACH_RADXA_ROCK3) += rk3568-rock-3a.dtb.o
lwl-$(CONFIG_MACH_RADXA_ROCK5) += rk3588-rock-5b.dtb.o
diff --git a/arch/arm/dts/stm32mp151-mecio1.dts b/arch/arm/dts/stm32mp151-mecio1.dts
new file mode 100644
index 0000000000..6b50bdd4ef
--- /dev/null
+++ b/arch/arm/dts/stm32mp151-mecio1.dts
@@ -0,0 +1,214 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Protonic Holland
+ * Author: David Jander <david at protonic.nl>
+ */
+/dts-v1/;
+
+#include "arm/st/stm32mp151.dtsi"
+#include "arm/st/stm32mp15xc.dtsi"
+#include "arm/st/stm32mp15-pinctrl.dtsi"
+#include "arm/st/stm32mp15xxaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Protonic MECIO1";
+ compatible = "prt,mecio1", "st,stm32mp151";
+
+ chosen {
+ stdout-path = "serial0:1500000n8";
+ };
+
+ aliases {
+ serial0 = &uart4;
+ ethernet0 = ðernet0;
+ };
+
+ v3v3: fixed-regulator-v3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "v3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ v5v: fixed-regulator-v5v {
+ compatible = "regulator-fixed";
+ regulator-name = "v5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ led {
+ compatible = "gpio-leds";
+
+ led-0 {
+ label = "debug:red";
+ gpios = <&gpioa 13 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-1 {
+ label = "debug:green";
+ gpios = <&gpioa 14 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&clk_hse {
+ clock-frequency = <25000000>;
+};
+
+&clk_lse {
+ status = "disabled";
+};
+
+&qspi {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qspi_clk_pins_a
+ &qspi_bk1_pins_a
+ &qspi_cs1_pins_a>;
+ pinctrl-1 = <&qspi_clk_sleep_pins_a
+ &qspi_bk1_sleep_pins_a
+ &qspi_cs1_sleep_pins_a>;
+ status = "okay";
+
+ flash at 0 {
+ compatible = "spi-nor";
+ reg = <0>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <104000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
+&qspi_bk1_pins_a {
+ pins1 {
+ bias-pull-up;
+ drive-push-pull;
+ slew-rate = <1>;
+ };
+};
+
+ðernet0 {
+ status = "okay";
+ pinctrl-0 = <ðernet0_rgmii_pins_x>;
+ pinctrl-1 = <ðernet0_rgmii_sleep_pins_x>;
+ pinctrl-names = "default", "sleep";
+ phy-mode = "rgmii-id";
+ phy-handle = <&phy0>;
+ assigned-clocks = <&rcc ETHCK_K>, <&rcc PLL3_Q>;
+ assigned-clock-parents = <&rcc PLL3_Q>;
+ assigned-clock-rates = <125000000>; /* Clock PLL4 to 750Mhz in ATF/U-Boot */
+ st,eth-clk-sel;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+
+ phy0: ethernet-phy at 8 {
+ reg = <8>;
+ interrupts-extended = <&gpiog 7 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpiog 10 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10>;
+ reset-deassert-us = <35>;
+ };
+ };
+};
+
+&usbotg_hs {
+ dr_mode = "host";
+ pinctrl-0 = <&usbotg_hs_pins_a>;
+ pinctrl-names = "default";
+ phys = <&usbphyc_port1 0>;
+ phy-names = "usb2-phy";
+ vbus-supply = <&v5v>;
+ status = "okay";
+};
+
+&usbphyc {
+ status = "okay";
+};
+
+&usbphyc_port1 {
+ phy-supply = <&v3v3>;
+};
+
+&uart4 {
+ pinctrl-names = "default", "sleep", "idle";
+ pinctrl-0 = <&uart4_pins_a>;
+ pinctrl-1 = <&uart4_sleep_pins_a>;
+ pinctrl-2 = <&uart4_idle_pins_a>;
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ status = "okay";
+};
+
+&uart4_pins_a {
+ pins1 {
+ pinmux = <STM32_PINMUX('B', 9, AF8)>; /* UART4_TX */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+ bias-pull-up;
+ };
+};
+
+&pinctrl {
+ ethernet0_rgmii_pins_x: rgmii-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */
+ <STM32_PINMUX('G', 4, AF11)>, /* ETH_RGMII_GTX_CLK */
+ <STM32_PINMUX('B', 12, AF11)>, /* ETH_RGMII_TXD0 */
+ <STM32_PINMUX('B', 13, AF11)>, /* ETH_RGMII_TXD1 */
+ <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */
+ <STM32_PINMUX('B', 8, AF11)>, /* ETH_RGMII_TXD3 */
+ <STM32_PINMUX('B', 11, AF11)>, /* ETH_RGMII_TX_CTL */
+ <STM32_PINMUX('C', 1, AF11)>; /* ETH_MDC */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('A', 2, AF11)>; /* ETH_MDIO */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins3 {
+ pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */
+ <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */
+ <STM32_PINMUX('H', 6, AF11)>, /* ETH_RGMII_RXD2 */
+ <STM32_PINMUX('H', 7, AF11)>, /* ETH_RGMII_RXD3 */
+ <STM32_PINMUX('A', 1, AF11)>, /* ETH_RGMII_RX_CLK */
+ <STM32_PINMUX('A', 7, AF11)>; /* ETH_RGMII_RX_CTL */
+ bias-disable;
+ };
+ };
+
+ ethernet0_rgmii_sleep_pins_x: rgmii-sleep-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('G', 5, ANALOG)>, /* ETH_RGMII_CLK125 */
+ <STM32_PINMUX('G', 4, ANALOG)>, /* ETH_RGMII_GTX_CLK */
+ <STM32_PINMUX('B', 12, ANALOG)>, /* ETH_RGMII_TXD0 */
+ <STM32_PINMUX('B', 13, ANALOG)>, /* ETH_RGMII_TXD1 */
+ <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_TXD2 */
+ <STM32_PINMUX('B', 8, ANALOG)>, /* ETH_RGMII_TXD3 */
+ <STM32_PINMUX('B', 11, ANALOG)>, /* ETH_RGMII_TX_CTL */
+ <STM32_PINMUX('A', 2, ANALOG)>, /* ETH_MDIO */
+ <STM32_PINMUX('C', 1, ANALOG)>, /* ETH_MDC */
+ <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_RXD0 */
+ <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RGMII_RXD1 */
+ <STM32_PINMUX('H', 6, ANALOG)>, /* ETH_RGMII_RXD2 */
+ <STM32_PINMUX('H', 7, ANALOG)>, /* ETH_RGMII_RXD3 */
+ <STM32_PINMUX('A', 1, ANALOG)>, /* ETH_RGMII_RX_CLK */
+ <STM32_PINMUX('A', 7, ANALOG)>; /* ETH_RGMII_RX_CTL */
+ };
+ };
+};
diff --git a/arch/arm/mach-stm32mp/Kconfig b/arch/arm/mach-stm32mp/Kconfig
index 524d282a1d..d9db74a576 100644
--- a/arch/arm/mach-stm32mp/Kconfig
+++ b/arch/arm/mach-stm32mp/Kconfig
@@ -43,10 +43,10 @@ config MACH_STM32MP15X_EV1
config MACH_PROTONIC_STM32MP1
select ARCH_STM32MP157
- bool "Protonic PRTT1L family of boards"
+ bool "Protonic PRTT1L/MECIOx family of boards"
help
- Builds all barebox-prtt1*.stm32 that can be deployed as SSBL
- on the respective PRTT1L family board
+ Builds all barebox-*.stm32 that can be deployed as SSBL
+ on the respective PRTT1L/MECIOx family board
config MACH_PHYTEC_PHYCORE_STM32MP1
select ARCH_STM32MP157
diff --git a/images/Makefile.stm32mp b/images/Makefile.stm32mp
index cc70aee923..663c08a741 100644
--- a/images/Makefile.stm32mp
+++ b/images/Makefile.stm32mp
@@ -38,6 +38,7 @@ $(call build_stm32mp_image, CONFIG_MACH_LXA_MC1, start_stm32mp157c_lxa_mc1, stm3
$(call build_stm32mp_image, CONFIG_MACH_PROTONIC_STM32MP1, start_prtt1a, prtt1a)
$(call build_stm32mp_image, CONFIG_MACH_PROTONIC_STM32MP1, start_prtt1s, prtt1s)
$(call build_stm32mp_image, CONFIG_MACH_PROTONIC_STM32MP1, start_prtt1c, prtt1c)
+$(call build_stm32mp_image, CONFIG_MACH_PROTONIC_STM32MP1, start_mecio1, mecio1)
$(call build_stm32mp_image, CONFIG_MACH_SEEED_ODYSSEY, start_stm32mp157c_seeed_odyssey, stm32mp157c-seeed-odyssey)
--
2.39.2
More information about the barebox
mailing list