[PATCH v3 4/4] ARM: novena: Use DDR3 information from SPD EEPROM

[John Watts]

The Novena supports swappable memory which means we must query the memory
for configuration details. This patch uses values stored in the SPD EEPROM
to configure the i.MX6 memory controller.

If the SPD can't be read, the default configuration for a 4GB stick is used.

Calibration for the installed stick is run unconditionally.

Verification that this works was done by comparing MMDC registers before and
after and carefully reading other people's source code.

Signed-off-by: John Watts <contact at jookia.org>
---
 arch/arm/boards/novena/lowlevel.c | 108 ++++++++++++++++++++++++++++++
 arch/arm/mach-imx/Kconfig         |   2 +
 2 files changed, 110 insertions(+)

diff --git a/arch/arm/boards/novena/lowlevel.c b/arch/arm/boards/novena/lowlevel.c
index 3acf983ee0..54980bda4e 100644
--- a/arch/arm/boards/novena/lowlevel.c
+++ b/arch/arm/boards/novena/lowlevel.c
@@ -3,6 +3,8 @@
 
 #include <asm/barebox-arm.h>
 #include <common.h>
+#include <ddr_dimms.h>
+#include <ddr_spd.h>
 #include <debug_ll.h>
 #include <mach/esdctl.h>
 #include <mach/generic.h>
@@ -10,6 +12,7 @@
 #include <mach/imx6-mmdc.h>
 #include <mach/iomux-mx6.h>
 #include <mach/xload.h>
+#include <pbl/i2c.h>
 #include <soc/fsl/fsl_udc.h>
 #include "ddr_regs.h"
 
@@ -17,6 +20,106 @@
 
 extern char __dtb_imx6q_novena_start[];
 
+static struct spd_eeprom spd_eeprom;
+static struct dimm_params dimm_params;
+
+static struct pbl_i2c *setup_spd_i2c(void)
+{
+	void __iomem *iomuxbase = IOMEM(MX6_IOMUXC_BASE_ADDR);
+
+	imx_setup_pad(iomuxbase, MX6Q_PAD_CSI0_DAT8__I2C1_SDA);
+	imx_setup_pad(iomuxbase, MX6Q_PAD_CSI0_DAT9__I2C1_SCL);
+
+	return imx6_i2c_early_init(IOMEM(MX6_I2C1_BASE_ADDR));
+}
+
+static struct spd_eeprom *read_spd(void)
+{
+	struct spd_eeprom *eeprom = &spd_eeprom;
+	struct pbl_i2c *i2c = setup_spd_i2c();
+	int rc;
+
+	rc = spd_read_eeprom(i2c, 0x50, eeprom, SPD_MEMTYPE_DDR3);
+	if (rc < 0) {
+		pr_err("Couldn't read SPD EEPROM: %i\n", rc);
+		return NULL;
+	}
+
+	rc = ddr3_spd_check(&eeprom->ddr3);
+	if (rc < 0) {
+		pr_err("Couldn't verify SPD data: %i\n", rc);
+		return NULL;
+	}
+
+	return eeprom;
+}
+
+static bool check_spd_compatible(struct spd_eeprom *eeprom)
+{
+	if (eeprom->ddr3.mem_type != 0x0b) {
+		pr_err("SPD data is not DDR3\n");
+		return false;
+	}
+
+	if ((eeprom->ddr3.bus_width & 0x1f) != 0x03) {
+		pr_err("SPD data is for a 64-bit bus\n");
+		return false;
+	}
+
+	return true;
+}
+
+static void setup_dimm_settings(struct dimm_params *params,
+				struct mx6_ddr_sysinfo *info,
+				struct mx6_ddr3_cfg *cfg)
+{
+	int capacity_gbit = params->capacity / 0x8000000;
+	int density_rank = capacity_gbit / params->n_ranks;
+
+	info->ncs = params->n_ranks;
+	info->cs_density = density_rank;
+	cfg->mem_speed = params->tckmin_x_ps;
+	cfg->density = density_rank / params->n_banks_per_sdram_device;
+	cfg->width = params->data_width;
+	cfg->banks = params->n_banks_per_sdram_device;
+	cfg->rowaddr = params->n_row_addr;
+	cfg->coladdr = params->n_col_addr;
+	cfg->trcd = params->trcd_ps / 10;
+	cfg->trcmin = params->trc_ps / 10;
+	cfg->trasmin = params->tras_ps / 10;
+	cfg->SRT = params->extended_op_srt;
+
+	if (params->device_width >= 16)
+		cfg->pagesz = 2;
+}
+
+static void read_dimm_settings(void)
+{
+	struct spd_eeprom *eeprom = read_spd();
+	struct dimm_params *params = &dimm_params;
+	int rc;
+
+	if (!eeprom) {
+		pr_err("Couldn't read SPD EEPROM, using default settings\n");
+		return;
+	}
+
+	if (!check_spd_compatible(eeprom)) {
+		pr_err("DIMM stick incompatible\n");
+		hang();
+	}
+
+	rc = ddr3_compute_dimm_parameters(&eeprom->ddr3, params);
+	if (rc < 0) {
+		pr_err("Couldn't compute DIMM params: %i\n", rc);
+		return;
+	}
+
+	setup_dimm_settings(params, &novena_ddr_info, &novena_ddr_cfg);
+
+	pr_info("Found DIMM: %s\n", params->mpart);
+}
+
 static bool running_from_ram(void)
 {
 	return (get_pc() >= MX6_MMDC_PORT01_BASE_ADDR);
@@ -36,8 +139,13 @@ static void setup_uart(void)
 
 static void setup_ram(void)
 {
+	read_dimm_settings();
+
 	mx6dq_dram_iocfg(64, &novena_ddr_regs, &novena_grp_regs);
 	mx6_dram_cfg(&novena_ddr_info, &novena_mmdc_calib, &novena_ddr_cfg);
+
+	mmdc_do_write_level_calibration();
+	mmdc_do_dqs_calibration();
 }
 
 static void load_barebox(void)
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index 7993835be7..aa7a86da66 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -437,6 +437,8 @@ config MACH_NITROGEN6
 config MACH_NOVENA
 	bool "Kosagi Novena board"
 	select ARCH_IMX6
+	select DDR_SPD
+	select I2C_IMX_EARLY
 	select MCI_IMX_ESDHC_PBL
 	select USB_GADGET_DRIVER_ARC_PBL
 
-- 
2.39.1