[PATCH 18/21] net: update network docs
Sascha Hauer
s.hauer at pengutronix.de
Fri Nov 24 00:12:34 PST 2017
The network configuration has changed in the previous patches. Update
the documentation accordingly.
Signed-off-by: Sascha Hauer <s.hauer at pengutronix.de>
---
Documentation/user/networking.rst | 99 +++++++++++++++++++++++++++++++++++++--
1 file changed, 94 insertions(+), 5 deletions(-)
diff --git a/Documentation/user/networking.rst b/Documentation/user/networking.rst
index 8afb433837..53fa5b3c40 100644
--- a/Documentation/user/networking.rst
+++ b/Documentation/user/networking.rst
@@ -7,6 +7,49 @@ barebox has IPv4 networking support. Several protocols such as :ref:`DHCP
Network configuration
---------------------
+Lowlevel network device configuration
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+Network devices are configured with a set of device specific variables:
+
++-------------------+--------------+----------------------------------------------------+
+| name | type | |
++===================+==============+====================================================+
+| <devname>.mode | enum | "dhcp": DHCP is used to get IP address and netmask |
+| | | "static": Static IP setup described by variables |
+| | | below |
+| | | "disabled": Interface unused |
++===================+==============+====================================================+
+| <devname>.ipaddr | ipv4 address | The IP address when using static configuration |
++-------------------+--------------+----------------------------------------------------+
+| <devname>.netmask | ipv4 address | The netmask when using static configuration |
++-------------------+--------------+----------------------------------------------------+
+| <devname>.gateway | ipv4 address | Alias for global.net.gateway. For |
+| | | compatibility, do not use. |
++-------------------+--------------+----------------------------------------------------+
+| <devname>.serverip| ipv4 address | Alias for global.net.server. For |
+| | | compatibility, do not use. |
++-------------------+--------------+----------------------------------------------------+
+| <devname>.ethaddr | MAC address | The MAC address of this device |
++-------------------+--------------+----------------------------------------------------+
+
+Additionally there are some more variables that are not specific to a
+device:
+
++------------------------------+--------------+------------------------------------------------+
+| name | type | |
++==============================+==============+================================================+
+| global.net.gateway | ipv4 host | The network gateway used when a host is not in |
+| | | any directly visible subnet. May be set |
+| | | automatically by DHCP. |
++------------------------------+--------------+------------------------------------------------+
+| global.net.server | ipv4 host | The default server address. If unspecified, may|
+| | | be set by DHCP |
++------------------------------+--------------+------------------------------------------------+
+| global.net.nameserver | ipv4 address | The DNS server used for resolving host names. |
+| | | May be set by DHCP |
++------------------------------+--------------+------------------------------------------------+
+
The first step for networking is configuring the network device. The network
device is usually ``eth0``. The current configuration can be viewed with the
:ref:`devinfo <command_devinfo>` command:
@@ -16,10 +59,9 @@ device is usually ``eth0``. The current configuration can be viewed with the
barebox:/ devinfo eth0
Parameters:
ethaddr: 00:1c:49:01:03:4b
- gateway: 192.168.23.1
ipaddr: 192.168.23.197
netmask: 255.255.0.0
- serverip: 192.168.23.1
+ [...]
The configuration can be changed on the command line with:
@@ -30,9 +72,56 @@ The configuration can be changed on the command line with:
The :ref:`dhcp command <command_dhcp>` will change the settings based on the answer
from the DHCP server.
-This low-level configuration of the network interface is often not necessary. Normally
-the network settings should be edited in ``/env/network/eth0``, then the network interface
-can be brought up using the :ref:`ifup command <command_ifup>`.
+To make the network device settings persistent across reboots there is a nonvolatile
+variable (nvvar) for each of the varariables above. The network device specific variables
+are:
+
+.. code-block:: sh
+
+ nv.dev.<devname>.mode
+ nv.dev.<devname>.ipaddr
+ nv.dev.<devname>.netmask
+ nv.dev.<devname>.ethaddr
+
+The others are:
+
+.. code-block:: sh
+
+ nv.net.gateway
+ nv.net.server
+ nv.net.nameserver
+
+A typical simple network setting is to use DHCP. Provided the network interface is eth0
+then this would configure the network device for DHCP:
+
+.. code-block:: sh
+
+ nv dev.eth0.mode=dhcp
+
+(In fact DHCP is the default, so the above is not necessary)
+
+A static setup would look like:
+
+.. code-block:: sh
+
+ nv dev.eth0.mode=static
+ nv dev.eth0.ipaddr=192.168.0.17
+ nv dev.eth0.netmask=255.255.0.0
+ nv net.server=192.168.0.1
+
+The settings can be activated with the :ref:`ifup command <command_ifup>`:
+
+.. code-block:: sh
+
+ ifup eth0
+
+or:
+
+.. code-block:: sh
+
+ ifup -a
+
+'ifup -a' will activate all ethernet interfaces, also the ones on USB.
Network filesystems
-------------------
--
2.11.0
More information about the barebox
mailing list