[PATCH 06/16] i.MX: vf610: Ramp CPU clock to maximum frequency
Andrey Smirnov
andrew.smirnov at gmail.com
Mon Dec 5 06:54:34 PST 2016
Mask ROM leaves the CPU running at 264Mhz, so configure the clock tree
to such that CPU runs at maximum supported frequency, based on speed
grading burned into OCOTP fusebox.
Signed-off-by: Andrey Smirnov <andrew.smirnov at gmail.com>
---
arch/arm/mach-imx/Kconfig | 13 +++
drivers/clk/imx/clk-vf610.c | 187 +++++++++++++++++++++++++++++++++++++++++++-
2 files changed, 198 insertions(+), 2 deletions(-)
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index af533ea..1752335 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -750,6 +750,19 @@ config HABV3_IMG_CRT_DER
endif
+config ADJUST_CPU_CLOCK
+ bool "Adjust CPU clock based on its speed grading"
+ select IMX_OCOTP
+ depends on ARCH_VF610
+ default y
+ help
+ Some i.MX SoCs (e. g. Vybrid) are manufactured to have
+ several variants of the same chip different only in maxumum
+ CPU frequency supported. MaskROM on such chips plays it safe
+ and uses the lowest possible frequency. This option
+ configures Barebox to read chip's speed grade information
+ and increase CPU clock to it's highest possible value.
+
endmenu
endif
diff --git a/drivers/clk/imx/clk-vf610.c b/drivers/clk/imx/clk-vf610.c
index 04cb02f..1cf2b65 100644
--- a/drivers/clk/imx/clk-vf610.c
+++ b/drivers/clk/imx/clk-vf610.c
@@ -16,7 +16,9 @@
#include <of_address.h>
#include <linux/clkdev.h>
#include <linux/clk.h>
+#include <notifier.h>
#include <dt-bindings/clock/vf610-clock.h>
+#include <mach/vf610-regs.h>
#include "clk.h"
@@ -76,6 +78,7 @@
#define PLL6_CTRL (anatop_base + 0xa0)
#define PLL7_CTRL (anatop_base + 0x20)
#define ANA_MISC1 (anatop_base + 0x160)
+#define PLL_LOCK (anatop_base + 0x2c0)
static void __iomem *anatop_base;
static void __iomem *ccm_base;
@@ -188,8 +191,9 @@ static void __init vf610_clocks_init(struct device_node *ccm_node)
clk[VF610_CLK_PLL6_BYPASS_SRC] = imx_clk_mux("pll6_bypass_src", PLL6_CTRL, 14, 1, pll_bypass_src_sels, ARRAY_SIZE(pll_bypass_src_sels));
clk[VF610_CLK_PLL7_BYPASS_SRC] = imx_clk_mux("pll7_bypass_src", PLL7_CTRL, 14, 1, pll_bypass_src_sels, ARRAY_SIZE(pll_bypass_src_sels));
- clk[VF610_CLK_PLL1] = imx_clk_pllv3(IMX_PLLV3_GENERIC, "pll1", "pll1_bypass_src", PLL1_CTRL, 0x1);
- clk[VF610_CLK_PLL2] = imx_clk_pllv3(IMX_PLLV3_GENERIC, "pll2", "pll2_bypass_src", PLL2_CTRL, 0x1);
+ clk[VF610_CLK_PLL1] = imx_clk_pllv3_locked(IMX_PLLV3_SYS_VF610, "pll1", "pll1_bypass_src", PLL1_CTRL, 0x1, PLL_LOCK, BIT(6));
+ clk[VF610_CLK_PLL2] = imx_clk_pllv3_locked(IMX_PLLV3_SYS_VF610, "pll2", "pll2_bypass_src", PLL2_CTRL, 0x1, PLL_LOCK, BIT(5));
+
clk[VF610_CLK_PLL3] = imx_clk_pllv3(IMX_PLLV3_USB_VF610, "pll3", "pll3_bypass_src", PLL3_CTRL, 0x2);
clk[VF610_CLK_PLL4] = imx_clk_pllv3(IMX_PLLV3_AV, "pll4", "pll4_bypass_src", PLL4_CTRL, 0x7f);
clk[VF610_CLK_PLL5] = imx_clk_pllv3(IMX_PLLV3_ENET, "pll5", "pll5_bypass_src", PLL5_CTRL, 0x3);
@@ -441,3 +445,182 @@ static void __init vf610_clocks_init(struct device_node *ccm_node)
of_clk_add_provider(np, of_clk_src_onecell_get, &clk_data);
}
CLK_OF_DECLARE(vf610, "fsl,vf610-ccm", vf610_clocks_init);
+
+#ifdef CONFIG_ADJUST_CPU_CLOCK
+
+enum {
+ OCOTP_SPEED_GRADING_OFFSET = (0x4 * sizeof(uint32_t)),
+ OCOTP_SPEED_GRADING_SHIFT = 18,
+ OCOTP_SPEED_GRADING_MASK = 0b1111,
+
+ VF610_SPEED_500 = 0b1110,
+ VF610_SPEED_400 = 0b1001,
+ VF610_SPEED_266 = 0b0001,
+
+ DDRMC_CR117 = 0x01d4,
+ DDRMC_CR117_AXI0_FITYPEREG_SYNC = 0b01 << 16,
+};
+
+static int vf610_switch_cpu_clock_to_500mhz(void)
+{
+ int ret;
+
+ /*
+ * When switching A5 CPU to 500Mhz we expect DDRC to be
+ * clocked by PLL2_PFD2 and the system to be configured in
+ * asynchronous mode.
+ *
+ * We also can't just use default PFD1 output of PLL1 due to
+ * Errata e6235, so we have to re-clock the PLL itself and use
+ * its output to clock the CPU directly.
+ */
+
+ if (clk_get_parent(clk[VF610_CLK_DDR_SEL]) != clk[VF610_CLK_PLL2_PFD2]) {
+ pr_warn("DDRC is clocked by PLL1, can't switch CPU clock");
+ return -EINVAL;
+ }
+
+ ret = clk_set_parent(clk[VF610_CLK_SYS_SEL], clk[VF610_CLK_PLL2_BUS]);
+ if (ret < 0) {
+ pr_crit("Unable to re-parent '%s'\n",
+ clk[VF610_CLK_SYS_SEL]->name);
+ return ret;
+ }
+
+ ret = clk_set_rate(clk[VF610_CLK_PLL1], 500000000);
+ if (ret < 0) {
+ pr_crit("Unable to set %s to 500Mhz %d\n",
+ clk[VF610_CLK_PLL1]->name, ret);
+ return ret;
+ }
+
+ ret = clk_set_parent(clk[VF610_CLK_PLL1_PFD_SEL], clk[VF610_CLK_PLL1_SYS]);
+ if (ret < 0) {
+ pr_crit("Unable to re-parent '%s'\n",
+ clk[VF610_CLK_PLL1_PFD_SEL]->name);
+ return ret;
+ }
+
+ ret = clk_set_parent(clk[VF610_CLK_SYS_SEL], clk[VF610_CLK_PLL1_PFD_SEL]);
+ if (ret < 0) {
+ pr_crit("Unable to re-parent '%s'\n",
+ clk[VF610_CLK_SYS_SEL]->name);
+ return ret;
+ }
+
+ /*
+ * imx_clk_divider has no error path in its set_rate hook
+ */
+ clk_set_rate(clk[VF610_CLK_SYS_BUS], clk_get_rate(clk[VF610_CLK_SYS_SEL]));
+ clk_set_rate(clk[VF610_CLK_PLATFORM_BUS], clk_get_rate(clk[VF610_CLK_SYS_BUS]) / 3);
+
+ return ret;
+}
+
+static int vf610_switch_cpu_clock_to_400mhz(void)
+{
+ int ret;
+ uint32_t cr117;
+ void * __iomem ddrmc = IOMEM(VF610_DDR_BASE_ADDR);
+
+ if (clk_get_parent(clk[VF610_CLK_DDR_SEL]) != clk[VF610_CLK_PLL2_PFD2]) {
+ pr_warn("DDRC is clocked by PLL1, can't switch CPU clock");
+ return -EINVAL;
+ }
+
+ ret = clk_set_parent(clk[VF610_CLK_PLL2_PFD_SEL], clk[VF610_CLK_PLL2_PFD2]);
+ if (ret < 0) {
+ pr_crit("Unable to re-parent '%s'\n",
+ clk[VF610_CLK_PLL2_PFD_SEL]->name);
+ return ret;
+ }
+
+ ret = clk_set_parent(clk[VF610_CLK_SYS_SEL], clk[VF610_CLK_PLL2_PFD_SEL]);
+ if (ret < 0) {
+ pr_crit("Unable to re-parent '%s'\n",
+ clk[VF610_CLK_SYS_SEL]->name);
+ return ret;
+ }
+
+ /*
+ * imx_clk_divider has no error path in its set_rate hook
+ */
+ clk_set_rate(clk[VF610_CLK_SYS_BUS], clk_get_rate(clk[VF610_CLK_SYS_SEL]));
+ clk_set_rate(clk[VF610_CLK_PLATFORM_BUS], clk_get_rate(clk[VF610_CLK_SYS_BUS]) / 3);
+
+ /*
+ * Now that we are running off of the same clock as DDRMC we
+ * shouldn't need to use clock domain corssing FIFO and
+ * asynchronous mode and instead can swithch to sychronous
+ * mode for AXI0 accesses
+ */
+ cr117 = readl(ddrmc + DDRMC_CR117);
+ cr117 |= DDRMC_CR117_AXI0_FITYPEREG_SYNC;
+ writel(cr117, ddrmc + DDRMC_CR117);
+
+ return 0;
+}
+
+static int vf610_switch_cpu_clock(void)
+{
+ int ret;
+ struct device_node *ocotp_node;
+ struct cdev *ocotp;
+ uint32_t speed_grading;
+
+ if (!of_machine_is_compatible("fsl,vf610"))
+ return 0;
+
+ ocotp_node = of_find_compatible_node(NULL, NULL, "fsl,vf610-ocotp");
+ if (!ocotp_node) {
+ pr_err("Unable to find OCOTP DT node\n");
+ return -ENODEV;
+ }
+
+ ocotp = cdev_by_device_node(ocotp_node);
+ if (!ocotp) {
+ pr_err("No OCOTP character device\n");
+ return -ENODEV;
+ }
+
+ ret = cdev_read(ocotp, &speed_grading, sizeof(speed_grading),
+ OCOTP_SPEED_GRADING_OFFSET, 0);
+ if (ret != sizeof(speed_grading)) {
+ pr_err("Failed to read speed grading data\n");
+ return ret < 0 ? ret : -EIO;
+ }
+
+ speed_grading >>= OCOTP_SPEED_GRADING_SHIFT;
+ speed_grading &= OCOTP_SPEED_GRADING_MASK;
+
+ switch (speed_grading) {
+ default:
+ pr_err("Unknown CPU speed grading %x\n", speed_grading);
+ return -EINVAL;
+
+ case VF610_SPEED_266:
+ return 0;
+
+ case VF610_SPEED_500:
+ ret = vf610_switch_cpu_clock_to_500mhz();
+ break;
+
+ case VF610_SPEED_400:
+ ret = vf610_switch_cpu_clock_to_400mhz();
+ break;
+ }
+
+ clock_notifier_call_chain();
+ return ret;
+}
+/*
+ * We can probably gain a bit of a boot speed if we switch CPU clock
+ * earlier, but if we do this we'd need to figure out a way how to
+ * re-adjust the baud rate settings of the UART for DEBUG_LL
+ * functionality, or, accept the fact that it will be unavailbe after
+ * this hook is executed. Both are far from ideal, so a bit slower
+ * boot it is.
+ */
+postconsole_initcall(vf610_switch_cpu_clock);
+
+#endif
--
2.5.5
More information about the barebox
mailing list