[PATCH] usb: chipidea: imx: add vbus regulator support

[Sebastian Hesselbarth]

On 06/30/2014 09:52 AM, Steffen Trumtrar wrote:
> The chipidea binding describes the optional property of a regulator
> for vbus named "vbus-supply".
> 
> Add support for this property to the driver so it can be used on boards
> with a gpio-controlled regulator.
> 
> Signed-off-by: Steffen Trumtrar <s.trumtrar at pengutronix.de>
> ---
>  drivers/usb/imx/chipidea-imx.c | 15 ++++++++++++++-
>  1 file changed, 14 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/usb/imx/chipidea-imx.c b/drivers/usb/imx/chipidea-imx.c
> index 9b6829b..84522dc 100644
> --- a/drivers/usb/imx/chipidea-imx.c
> +++ b/drivers/usb/imx/chipidea-imx.c
> @@ -18,6 +18,7 @@
>  #include <of.h>
>  #include <errno.h>
>  #include <driver.h>
> +#include <regulator.h>
>  #include <usb/usb.h>
>  #include <usb/ehci.h>
>  #include <usb/chipidea-imx.h>
> @@ -32,6 +33,7 @@ struct imx_chipidea {
>  	struct ehci_data data;
>  	unsigned long flags;
>  	enum imx_usb_mode mode;
> +	struct regulator *reg_vbus;
>  	int portno;
>  	enum usb_phy_interface phymode;
>  };
> @@ -41,6 +43,12 @@ static int imx_chipidea_port_init(void *drvdata)
>  	struct imx_chipidea *ci = drvdata;
>  	int ret;
>  
> +	if (ci->reg_vbus) {
> +		ret = regulator_enable(ci->reg_vbus);
> +		if (ret < 0)
> +			return ret;
> +	}

Isn't barebox's regulator support using the dummy regulator, too?
A NULL regulator is interpreted as dummy regulator and can be used
with regulator API without checking each time.

>  	if ((ci->flags & MXC_EHCI_PORTSC_MASK) == MXC_EHCI_MODE_ULPI) {
>  		dev_dbg(ci->dev, "using ULPI phy\n");
>  		if (IS_ENABLED(CONFIG_USB_ULPI)) {
> @@ -54,8 +62,11 @@ static int imx_chipidea_port_init(void *drvdata)
>  			ret = -ENODEV;
>  		}
>  
> -		if (ret)
> +		if (ret) {
> +			if (ci->reg_vbus)
> +				regulator_disable(ci->reg_vbus);
>  			return ret;
> +		}
>  	}
>  
>  	ret = imx_usbmisc_port_init(ci->portno, ci->flags);
> @@ -126,6 +137,8 @@ static int imx_chipidea_probe_dt(struct imx_chipidea *ci)
>  				"disable-over-current", NULL))
>  		ci->flags |= MXC_EHCI_DISABLE_OVERCURRENT;
>  
> +	ci->reg_vbus = regulator_get(ci->dev, "vbus");
> +

Here, you should check for IS_ERR(ci->reg_vbus) and bail out if there is
an error. No property found should return NULL and therefore the dummy
regulator.

Sebastian

>  	return 0;
>  }
>  
>