[PATCH 12/15] mci: replace pr_debug with dev_dbg
Sascha Hauer
s.hauer at pengutronix.de
Thu Feb 9 06:53:55 EST 2012
The mci layer uses pr_debug throughout. Use dev_dbg instead
which is very useful when multiple cards are involved.
Signed-off-by: Sascha Hauer <s.hauer at pengutronix.de>
---
drivers/mci/mci-core.c | 118 ++++++++++++++++++++++++------------------------
1 files changed, 59 insertions(+), 59 deletions(-)
diff --git a/drivers/mci/mci-core.c b/drivers/mci/mci-core.c
index 49e1c42..799c5cb 100644
--- a/drivers/mci/mci-core.c
+++ b/drivers/mci/mci-core.c
@@ -215,7 +215,7 @@ static int mci_go_idle(struct mci *mci)
err = mci_send_cmd(mci, &cmd, NULL);
if (err) {
- pr_debug("Activating IDLE state failed: %d\n", err);
+ dev_dbg(mci->mci_dev, "Activating IDLE state failed: %d\n", err);
return err;
}
@@ -251,7 +251,7 @@ static int sd_send_op_cond(struct mci *mci)
mci_setup_cmd(&cmd, MMC_CMD_APP_CMD, 0, MMC_RSP_R1);
err = mci_send_cmd(mci, &cmd, NULL);
if (err) {
- pr_debug("Preparing SD for operating conditions failed: %d\n", err);
+ dev_dbg(mci->mci_dev, "Preparing SD for operating conditions failed: %d\n", err);
return err;
}
@@ -260,7 +260,7 @@ static int sd_send_op_cond(struct mci *mci)
MMC_RSP_R3);
err = mci_send_cmd(mci, &cmd, NULL);
if (err) {
- pr_debug("SD operation condition set failed: %d\n", err);
+ dev_dbg(mci->mci_dev, "SD operation condition set failed: %d\n", err);
return err;
}
udelay(1000);
@@ -273,7 +273,7 @@ static int sd_send_op_cond(struct mci *mci)
} while (busy && timeout--);
if (timeout <= 0) {
- pr_debug("SD operation condition set timed out\n");
+ dev_dbg(mci->mci_dev, "SD operation condition set timed out\n");
return -ENODEV;
}
@@ -316,7 +316,7 @@ static int mmc_send_op_cond(struct mci *mci)
err = mci_send_cmd(mci, &cmd, NULL);
if (err) {
- pr_debug("Preparing MMC for operating conditions failed: %d\n", err);
+ dev_dbg(mci->mci_dev, "Preparing MMC for operating conditions failed: %d\n", err);
return err;
}
@@ -324,7 +324,7 @@ static int mmc_send_op_cond(struct mci *mci)
} while (!(cmd.response[0] & OCR_BUSY) && timeout--);
if (timeout <= 0) {
- pr_debug("SD operation condition set timed out\n");
+ dev_dbg(mci->mci_dev, "SD operation condition set timed out\n");
return -ENODEV;
}
@@ -405,7 +405,7 @@ static int mmc_change_freq(struct mci *mci)
err = mci_send_ext_csd(mci, ext_csd);
if (err) {
- pr_debug("Preparing for frequency setup failed: %d\n", err);
+ dev_dbg(mci->mci_dev, "Preparing for frequency setup failed: %d\n", err);
return err;
}
@@ -414,7 +414,7 @@ static int mmc_change_freq(struct mci *mci)
err = mci_switch(mci, EXT_CSD_CMD_SET_NORMAL, EXT_CSD_HS_TIMING, 1);
if (err) {
- pr_debug("MMC frequency changing failed: %d\n", err);
+ dev_dbg(mci->mci_dev, "MMC frequency changing failed: %d\n", err);
return err;
}
@@ -422,7 +422,7 @@ static int mmc_change_freq(struct mci *mci)
err = mci_send_ext_csd(mci, ext_csd);
if (err) {
- pr_debug("Verifying frequency change failed: %d\n", err);
+ dev_dbg(mci->mci_dev, "Verifying frequency change failed: %d\n", err);
return err;
}
@@ -490,14 +490,14 @@ static int sd_change_freq(struct mci *mci)
if (mmc_host_is_spi(host))
return 0;
- pr_debug("Changing transfer frequency\n");
+ dev_dbg(mci->mci_dev, "Changing transfer frequency\n");
mci->card_caps = 0;
/* Read the SCR to find out if this card supports higher speeds */
mci_setup_cmd(&cmd, MMC_CMD_APP_CMD, mci->rca << 16, MMC_RSP_R1);
err = mci_send_cmd(mci, &cmd, NULL);
if (err) {
- pr_debug("Query SD card capabilities failed: %d\n", err);
+ dev_dbg(mci->mci_dev, "Query SD card capabilities failed: %d\n", err);
return err;
}
@@ -506,7 +506,7 @@ static int sd_change_freq(struct mci *mci)
timeout = 3;
retry_scr:
- pr_debug("Trying to read the SCR (try %d of %d)\n", 4 - timeout, 3);
+ dev_dbg(mci->mci_dev, "Trying to read the SCR (try %d of %d)\n", 4 - timeout, 3);
data.dest = (char *)scr;
data.blocksize = 8;
data.blocks = 1;
@@ -514,12 +514,12 @@ retry_scr:
err = mci_send_cmd(mci, &cmd, &data);
if (err) {
- pr_debug(" Catch error (%d)", err);
+ dev_dbg(mci->mci_dev, " Catch error (%d)", err);
if (timeout--) {
- pr_debug("-- retrying\n");
+ dev_dbg(mci->mci_dev, "-- retrying\n");
goto retry_scr;
}
- pr_debug("-- giving up\n");
+ dev_dbg(mci->mci_dev, "-- giving up\n");
return err;
}
@@ -550,7 +550,7 @@ retry_scr:
err = sd_switch(mci, SD_SWITCH_CHECK, 0, 1,
(uint8_t*)switch_status);
if (err) {
- pr_debug("Checking SD transfer switch frequency feature failed: %d\n", err);
+ dev_dbg(mci->mci_dev, "Checking SD transfer switch frequency feature failed: %d\n", err);
return err;
}
@@ -568,7 +568,7 @@ retry_scr:
err = sd_switch(mci, SD_SWITCH_SWITCH, 0, 1, (uint8_t*)switch_status);
if (err) {
- pr_debug("Switching SD transfer frequency failed: %d\n", err);
+ dev_dbg(mci->mci_dev, "Switching SD transfer frequency failed: %d\n", err);
return err;
}
@@ -718,13 +718,13 @@ static void mci_extract_max_tran_speed_from_csd(struct mci *mci)
unit = tran_speed_unit[(mci->csd[0] & 0x7)];
time = tran_speed_time[((mci->csd[0] >> 3) & 0xf)];
if ((unit == 0) || (time == 0)) {
- pr_debug("Unsupported 'TRAN_SPEED' unit/time value."
+ dev_dbg(mci->mci_dev, "Unsupported 'TRAN_SPEED' unit/time value."
" Can't calculate card's max. transfer speed\n");
return;
}
mci->tran_speed = time * unit;
- pr_debug("Transfer speed: %u\n", mci->tran_speed);
+ dev_dbg(mci->mci_dev, "Transfer speed: %u\n", mci->tran_speed);
}
/**
@@ -742,7 +742,7 @@ static void mci_extract_block_lengths_from_csd(struct mci *mci)
else
mci->write_bl_len = 1 << ((mci->csd[3] >> 22) & 0xf);
- pr_debug("Max. block length are: Write=%u, Read=%u Bytes\n",
+ dev_dbg(mci->mci_dev, "Max. block length are: Write=%u, Read=%u Bytes\n",
mci->write_bl_len, mci->read_bl_len);
}
@@ -764,7 +764,7 @@ static void mci_extract_card_capacity_from_csd(struct mci *mci)
mci->capacity = (csize + 1) << (cmult + 2);
mci->capacity *= mci->read_bl_len;
- pr_debug("Capacity: %u MiB\n", (unsigned)mci->capacity >> 20);
+ dev_dbg(mci->mci_dev, "Capacity: %u MiB\n", (unsigned)mci->capacity >> 20);
}
/**
@@ -785,25 +785,25 @@ static int mci_startup(struct mci *mci)
err = mci_send_cmd(mci, &cmd, NULL);
if (err) {
- pr_debug("Can't enable CRC check : %d\n", err);
+ dev_dbg(mci->mci_dev, "Can't enable CRC check : %d\n", err);
return err;
}
}
#endif
- pr_debug("Put the Card in Identify Mode\n");
+ dev_dbg(mci->mci_dev, "Put the Card in Identify Mode\n");
/* Put the Card in Identify Mode */
mci_setup_cmd(&cmd, mmc_host_is_spi(host) ? MMC_CMD_SEND_CID : MMC_CMD_ALL_SEND_CID, 0, MMC_RSP_R2);
err = mci_send_cmd(mci, &cmd, NULL);
if (err) {
- pr_debug("Can't bring card into identify mode: %d\n", err);
+ dev_dbg(mci->mci_dev, "Can't bring card into identify mode: %d\n", err);
return err;
}
memcpy(mci->cid, cmd.response, 16);
- pr_debug("Card's identification data is: %08X-%08X-%08X-%08X\n",
+ dev_dbg(mci->mci_dev, "Card's identification data is: %08X-%08X-%08X-%08X\n",
mci->cid[0], mci->cid[1], mci->cid[2], mci->cid[3]);
/*
@@ -812,11 +812,11 @@ static int mci_startup(struct mci *mci)
* This also puts the cards into Standby State
*/
if (!mmc_host_is_spi(host)) { /* cmd not supported in spi */
- pr_debug("Get/Set relative address\n");
+ dev_dbg(mci->mci_dev, "Get/Set relative address\n");
mci_setup_cmd(&cmd, SD_CMD_SEND_RELATIVE_ADDR, mci->rca << 16, MMC_RSP_R6);
err = mci_send_cmd(mci, &cmd, NULL);
if (err) {
- pr_debug("Get/Set relative address failed: %d\n", err);
+ dev_dbg(mci->mci_dev, "Get/Set relative address failed: %d\n", err);
return err;
}
}
@@ -824,19 +824,19 @@ static int mci_startup(struct mci *mci)
if (IS_SD(mci))
mci->rca = (cmd.response[0] >> 16) & 0xffff;
- pr_debug("Get card's specific data\n");
+ dev_dbg(mci->mci_dev, "Get card's specific data\n");
/* Get the Card-Specific Data */
mci_setup_cmd(&cmd, MMC_CMD_SEND_CSD, mci->rca << 16, MMC_RSP_R2);
err = mci_send_cmd(mci, &cmd, NULL);
if (err) {
- pr_debug("Getting card's specific data failed: %d\n", err);
+ dev_dbg(mci->mci_dev, "Getting card's specific data failed: %d\n", err);
return err;
}
/* CSD is of 128 bit */
memcpy(mci->csd, cmd.response, 16);
- pr_debug("Card's specific data is: %08X-%08X-%08X-%08X\n",
+ dev_dbg(mci->mci_dev, "Card's specific data is: %08X-%08X-%08X-%08X\n",
mci->csd[0], mci->csd[1], mci->csd[2], mci->csd[3]);
mci_detect_version_from_csd(mci);
@@ -847,25 +847,25 @@ static int mci_startup(struct mci *mci)
/* sanitiy? */
if (mci->read_bl_len > SECTOR_SIZE) {
mci->read_bl_len = SECTOR_SIZE;
- pr_debug("Limiting max. read block size down to %u\n",
+ dev_dbg(mci->mci_dev, "Limiting max. read block size down to %u\n",
mci->read_bl_len);
}
if (mci->write_bl_len > SECTOR_SIZE) {
mci->write_bl_len = SECTOR_SIZE;
- pr_debug("Limiting max. write block size down to %u\n",
+ dev_dbg(mci->mci_dev, "Limiting max. write block size down to %u\n",
mci->read_bl_len);
}
- pr_debug("Read block length: %u, Write block length: %u\n",
+ dev_dbg(mci->mci_dev, "Read block length: %u, Write block length: %u\n",
mci->read_bl_len, mci->write_bl_len);
if (!mmc_host_is_spi(host)) { /* cmd not supported in spi */
- pr_debug("Select the card, and put it into Transfer Mode\n");
+ dev_dbg(mci->mci_dev, "Select the card, and put it into Transfer Mode\n");
/* Select the card, and put it into Transfer Mode */
mci_setup_cmd(&cmd, MMC_CMD_SELECT_CARD, mci->rca << 16, MMC_RSP_R1b);
err = mci_send_cmd(mci, &cmd, NULL);
if (err) {
- pr_debug("Putting in transfer mode failed: %d\n", err);
+ dev_dbg(mci->mci_dev, "Putting in transfer mode failed: %d\n", err);
return err;
}
}
@@ -883,19 +883,19 @@ static int mci_startup(struct mci *mci)
if (IS_SD(mci)) {
if (mci->card_caps & MMC_MODE_4BIT) {
- pr_debug("Prepare for bus width change\n");
+ dev_dbg(mci->mci_dev, "Prepare for bus width change\n");
mci_setup_cmd(&cmd, MMC_CMD_APP_CMD, mci->rca << 16, MMC_RSP_R1);
err = mci_send_cmd(mci, &cmd, NULL);
if (err) {
- pr_debug("Preparing SD for bus width change failed: %d\n", err);
+ dev_dbg(mci->mci_dev, "Preparing SD for bus width change failed: %d\n", err);
return err;
}
- pr_debug("Set SD bus width to 4 bit\n");
+ dev_dbg(mci->mci_dev, "Set SD bus width to 4 bit\n");
mci_setup_cmd(&cmd, SD_CMD_APP_SET_BUS_WIDTH, 2, MMC_RSP_R1);
err = mci_send_cmd(mci, &cmd, NULL);
if (err) {
- pr_debug("Changing SD bus width failed: %d\n", err);
+ dev_dbg(mci->mci_dev, "Changing SD bus width failed: %d\n", err);
/* TODO continue with 1 bit? */
return err;
}
@@ -908,22 +908,22 @@ static int mci_startup(struct mci *mci)
mci_set_clock(mci, 25000000);
} else {
if (mci->card_caps & MMC_MODE_4BIT) {
- pr_debug("Set MMC bus width to 4 bit\n");
+ dev_dbg(mci->mci_dev, "Set MMC bus width to 4 bit\n");
/* Set the card to use 4 bit*/
err = mci_switch(mci, EXT_CSD_CMD_SET_NORMAL,
EXT_CSD_BUS_WIDTH, EXT_CSD_BUS_WIDTH_4);
if (err) {
- pr_debug("Changing MMC bus width failed: %d\n", err);
+ dev_dbg(mci->mci_dev, "Changing MMC bus width failed: %d\n", err);
return err;
}
mci_set_bus_width(mci, MMC_BUS_WIDTH_4);
} else if (mci->card_caps & MMC_MODE_8BIT) {
- pr_debug("Set MMC bus width to 8 bit\n");
+ dev_dbg(mci->mci_dev, "Set MMC bus width to 8 bit\n");
/* Set the card to use 8 bit*/
err = mci_switch(mci, EXT_CSD_CMD_SET_NORMAL,
EXT_CSD_BUS_WIDTH, EXT_CSD_BUS_WIDTH_8);
if (err) {
- pr_debug("Changing MMC bus width failed: %d\n", err);
+ dev_dbg(mci->mci_dev, "Changing MMC bus width failed: %d\n", err);
return err;
}
mci_set_bus_width(mci, MMC_BUS_WIDTH_8);
@@ -967,15 +967,15 @@ static int sd_send_if_cond(struct mci *mci)
MMC_RSP_R7);
err = mci_send_cmd(mci, &cmd, NULL);
if (err) {
- pr_debug("Query interface conditions failed: %d\n", err);
+ dev_dbg(mci->mci_dev, "Query interface conditions failed: %d\n", err);
return err;
}
if ((cmd.response[0] & 0xff) != 0xaa) {
- pr_debug("Card cannot work with hosts supply voltages\n");
+ dev_dbg(mci->mci_dev, "Card cannot work with hosts supply voltages\n");
return -EINVAL;
} else {
- pr_debug("SD Card Rev. 2.00 or later detected\n");
+ dev_dbg(mci->mci_dev, "SD Card Rev. 2.00 or later detected\n");
mci->version = SD_VERSION_2;
}
@@ -1000,24 +1000,24 @@ static int __maybe_unused mci_sd_write(struct block_device *blk,
struct mci *mci = container_of(blk, struct mci, blk);
int rc;
- pr_debug("%s: Write %d block(s), starting at %d\n",
+ dev_dbg(mci->mci_dev, "%s: Write %d block(s), starting at %d\n",
__func__, num_blocks, block);
if (mci->write_bl_len != SECTOR_SIZE) {
- pr_debug("MMC/SD block size is not %d bytes (its %u bytes instead)\n",
+ dev_dbg(mci->mci_dev, "MMC/SD block size is not %d bytes (its %u bytes instead)\n",
SECTOR_SIZE, mci->read_bl_len);
return -EINVAL;
}
/* size of the block number field in the MMC/SD command is 32 bit only */
if (block > MAX_BUFFER_NUMBER) {
- pr_debug("Cannot handle block number %d. Too large!\n", block);
+ dev_dbg(mci->mci_dev, "Cannot handle block number %d. Too large!\n", block);
return -EINVAL;
}
rc = mci_block_write(mci, buffer, block, num_blocks);
if (rc != 0) {
- pr_debug("Writing block %d failed with %d\n", block, rc);
+ dev_dbg(mci->mci_dev, "Writing block %d failed with %d\n", block, rc);
return rc;
}
@@ -1040,11 +1040,11 @@ static int mci_sd_read(struct block_device *blk, void *buffer, int block,
struct mci *mci = container_of(blk, struct mci, blk);
int rc;
- pr_debug("%s: Read %d block(s), starting at %d\n",
+ dev_dbg(mci->mci_dev, "%s: Read %d block(s), starting at %d\n",
__func__, num_blocks, block);
if (mci->read_bl_len != 512) {
- pr_debug("MMC/SD block size is not 512 bytes (its %u bytes instead)\n",
+ dev_dbg(mci->mci_dev, "MMC/SD block size is not 512 bytes (its %u bytes instead)\n",
mci->read_bl_len);
return -EINVAL;
}
@@ -1056,7 +1056,7 @@ static int mci_sd_read(struct block_device *blk, void *buffer, int block,
rc = mci_read_block(mci, buffer, block, num_blocks);
if (rc != 0) {
- pr_debug("Reading block %d failed with %d\n", block, rc);
+ dev_dbg(mci->mci_dev, "Reading block %d failed with %d\n", block, rc);
return rc;
}
@@ -1244,7 +1244,7 @@ static int mci_card_probe(struct mci *mci)
rc = sd_send_op_cond(mci);
if (rc && rc == -ETIMEDOUT) {
/* If the command timed out, we check for an MMC card */
- pr_debug("Card seems to be a MultiMediaCard\n");
+ dev_dbg(mci->mci_dev, "Card seems to be a MultiMediaCard\n");
rc = mmc_send_op_cond(mci);
}
@@ -1253,11 +1253,11 @@ static int mci_card_probe(struct mci *mci)
rc = mci_startup(mci);
if (rc) {
- pr_debug("Card's startup fails with %d\n", rc);
+ dev_dbg(mci->mci_dev, "Card's startup fails with %d\n", rc);
goto on_error;
}
- pr_debug("Card is up and running now, registering as a disk\n");
+ dev_dbg(mci->mci_dev, "Card is up and running now, registering as a disk\n");
mci->ready_for_use = 1; /* TODO now or later? */
/*
@@ -1288,7 +1288,7 @@ static int mci_card_probe(struct mci *mci)
rc = 0; /* it's not a failure */
}
- pr_debug("SD Card successfully added\n");
+ dev_dbg(mci->mci_dev, "SD Card successfully added\n");
on_error:
if (rc != 0) {
@@ -1375,7 +1375,7 @@ static int mci_probe(struct device_d *mci_dev)
*/
rc = add_mci_parameter(mci_dev);
if (rc != 0) {
- pr_debug("Failed to add 'probe' parameter to the MCI device\n");
+ dev_dbg(mci->mci_dev, "Failed to add 'probe' parameter to the MCI device\n");
goto on_error;
}
}
@@ -1385,7 +1385,7 @@ static int mci_probe(struct device_d *mci_dev)
/* add params on demand */
rc = add_mci_parameter(mci_dev);
if (rc != 0) {
- pr_debug("Failed to add 'probe' parameter to the MCI device\n");
+ dev_dbg(mci->mci_dev, "Failed to add 'probe' parameter to the MCI device\n");
goto on_error;
}
#endif
--
1.7.9
More information about the barebox
mailing list