[PATCH] mxs: add support for mx28-evk
Wolfram Sang
w.sang at pengutronix.de
Fri Dec 23 14:13:31 EST 2011
This patch adds basic support for the mx28-evk board. Debug UART, MMC and FEC
have been successfully used.
Signed-off-by: Marc Kleine-Budde <mkl at pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang at pengutronix.de>
---
arch/arm/Makefile | 1 +
arch/arm/boards/freescale-mx28-evk/Makefile | 1 +
arch/arm/boards/freescale-mx28-evk/config.h | 16 +++
arch/arm/boards/freescale-mx28-evk/env/config | 67 ++++++++++++
arch/arm/boards/freescale-mx28-evk/mx28-evk.c | 141 +++++++++++++++++++++++++
arch/arm/configs/imx28evk_defconfig | 48 +++++++++
arch/arm/mach-mxs/Kconfig | 7 ++
arch/arm/mach-mxs/include/mach/iomux-imx28.h | 1 +
8 files changed, 282 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/boards/freescale-mx28-evk/Makefile
create mode 100644 arch/arm/boards/freescale-mx28-evk/config.h
create mode 100644 arch/arm/boards/freescale-mx28-evk/env/config
create mode 100644 arch/arm/boards/freescale-mx28-evk/mx28-evk.c
create mode 100644 arch/arm/configs/imx28evk_defconfig
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 0c42f3d..c981041 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -101,6 +101,7 @@ board-$(CONFIG_MACH_NESO) := guf-neso
board-$(CONFIG_MACH_MX23EVK) := freescale-mx23-evk
board-$(CONFIG_MACH_CHUMBY) := chumby_falconwing
board-$(CONFIG_MACH_TX28) := karo-tx28
+board-$(CONFIG_MACH_MX28EVK) := freescale-mx28-evk
board-$(CONFIG_MACH_FREESCALE_MX51_PDK) := freescale-mx51-pdk
board-$(CONFIG_MACH_FREESCALE_MX53_LOCO) := freescale-mx53-loco
board-$(CONFIG_MACH_GUF_CUPID) := guf-cupid
diff --git a/arch/arm/boards/freescale-mx28-evk/Makefile b/arch/arm/boards/freescale-mx28-evk/Makefile
new file mode 100644
index 0000000..3e1f53b
--- /dev/null
+++ b/arch/arm/boards/freescale-mx28-evk/Makefile
@@ -0,0 +1 @@
+obj-y += mx28-evk.o
diff --git a/arch/arm/boards/freescale-mx28-evk/config.h b/arch/arm/boards/freescale-mx28-evk/config.h
new file mode 100644
index 0000000..8f18fda
--- /dev/null
+++ b/arch/arm/boards/freescale-mx28-evk/config.h
@@ -0,0 +1,16 @@
+/*
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _CONFIG_H_
+# define _CONFIG_H_
+
+#endif /* _CONFIG_H_ */
diff --git a/arch/arm/boards/freescale-mx28-evk/env/config b/arch/arm/boards/freescale-mx28-evk/env/config
new file mode 100644
index 0000000..667641d
--- /dev/null
+++ b/arch/arm/boards/freescale-mx28-evk/env/config
@@ -0,0 +1,67 @@
+#!/bin/sh
+
+machine=mx28-evk
+#user=
+
+# use 'dhcp' to do dhcp in barebox and in kernel
+# use 'none' if you want to skip kernel ip autoconfiguration
+ip=dhcp
+
+# or set your networking parameters here
+#eth0.ipaddr=a.b.c.d
+#eth0.netmask=a.b.c.d
+#eth0.serverip=a.b.c.d
+#eth0.gateway=a.b.c.d
+#eth0.ethaddr=de:ad:be:ef:00:00
+
+# can be either 'tftp', 'nfs', 'nand', 'nor' or 'disk'
+kernel_loc=tftp
+# can be either 'net', 'nand', 'nor', 'disk' or 'initrd'
+rootfs_loc=net
+
+# for flash based rootfs: 'jffs2' or 'ubifs'
+# in case of disk any regular filesystem like 'ext2', 'ext3', 'reiserfs'
+rootfs_type=ext2
+# where is the rootfs in case of 'rootfs_loc=disk' (linux name)
+rootfs_part_linux_dev=mmcblk0p4
+rootfsimage=rootfs-${machine}.$rootfs_type
+
+# where is the kernel image in case of 'kernel_loc=disk'
+kernel_part=disk0.2
+
+# The image type of the kernel. Can be uimage, zimage, raw, or raw_lzo
+kernelimage_type=zimage
+kernelimage=zImage-$machine
+#kernelimage_type=uimage
+#kernelimage=uImage-$machine
+#kernelimage_type=raw
+#kernelimage=Image-$machine
+#kernelimage_type=raw_lzo
+#kernelimage=Image-$machine.lzo
+
+bareboximage=barebox-${machine}.bin
+bareboxenvimage=barebox-${machine}.bin
+
+if [ -n $user ]; then
+ bareboximage="$user"-"$bareboximage"
+ bareboxenvimage="$user"-"$bareboxenvimage"
+ kernelimage="$user"-"$kernelimage"
+ rootfsimage="$user"-"$rootfsimage"
+ nfsroot="/home/$user/nfsroot/$machine"
+else
+ nfsroot="/path/to/nfs/root"
+fi
+
+autoboot_timeout=3
+
+bootargs="console=ttyAMA0,115200"
+
+#nor_parts="256k(barebox)ro,128k(bareboxenv),3M(kernel),-(root)"
+#rootfs_mtdblock_nor=3
+
+#nand_parts="256k(barebox)ro,128k(bareboxenv),3M(kernel),-(root)"
+#nand_device="FIXME"
+#rootfs_mtdblock_nand=7
+
+# set a fancy prompt (if support is compiled in)
+PS1="\e[1;32mbarebox@\e[1;31m\h:\w\e[0m "
diff --git a/arch/arm/boards/freescale-mx28-evk/mx28-evk.c b/arch/arm/boards/freescale-mx28-evk/mx28-evk.c
new file mode 100644
index 0000000..b80b910
--- /dev/null
+++ b/arch/arm/boards/freescale-mx28-evk/mx28-evk.c
@@ -0,0 +1,141 @@
+/*
+ * Copyright (C) 2010 Juergen Beisert, Pengutronix <kernel at pengutronix.de>
+ * Copyright (C) 2011 Marc Kleine-Budde, Pengutronix <mkl at pengutronix.de>
+ * Copyright (C) 2011 Wolfram Sang, Pengutronix <w.sang at pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <environment.h>
+#include <errno.h>
+#include <fec.h>
+#include <gpio.h>
+#include <init.h>
+#include <mci.h>
+#include <io.h>
+
+#include <mach/clock.h>
+#include <mach/imx-regs.h>
+#include <mach/iomux-imx28.h>
+#include <mach/mci.h>
+
+#include <asm/armlinux.h>
+#include <asm/mmu.h>
+
+#include <generated/mach-types.h>
+
+#define MX28EVK_FEC_PHY_RESET_GPIO 141
+
+/* setup the CPU card internal signals */
+static const uint32_t mx28evk_pads[] = {
+ /* duart */
+ PWM0_DUART_RX | VE_3_3V,
+ PWM1_DUART_TX | VE_3_3V,
+
+ /* fec0 */
+ ENET_CLK | VE_3_3V | BITKEEPER(0),
+ ENET0_MDC | VE_3_3V | PULLUP(1),
+ ENET0_MDIO | VE_3_3V | PULLUP(1),
+ ENET0_TXD0 | VE_3_3V | PULLUP(1),
+ ENET0_TXD1 | VE_3_3V | PULLUP(1),
+ ENET0_TX_EN | VE_3_3V | PULLUP(1),
+ ENET0_TX_CLK | VE_3_3V | BITKEEPER(0),
+ ENET0_RXD0 | VE_3_3V | PULLUP(1),
+ ENET0_RXD1 | VE_3_3V | PULLUP(1),
+ ENET0_RX_EN | VE_3_3V | PULLUP(1),
+ /* send a "good morning" to the ext. phy 0 = reset */
+ ENET0_RX_CLK_GPIO | VE_3_3V | PULLUP(0) | GPIO_OUT | GPIO_VALUE(0),
+ /* phy power control 1 = on */
+ SSP1_D3_GPIO | VE_3_3V | PULLUP(0) | GPIO_OUT | GPIO_VALUE(0),
+
+ /* mmc0 */
+ SSP0_D0 | VE_3_3V | PULLUP(1),
+ SSP0_D1 | VE_3_3V | PULLUP(1),
+ SSP0_D2 | VE_3_3V | PULLUP(1),
+ SSP0_D3 | VE_3_3V | PULLUP(1),
+ SSP0_D4 | VE_3_3V | PULLUP(1),
+ SSP0_D5 | VE_3_3V | PULLUP(1),
+ SSP0_D6 | VE_3_3V | PULLUP(1),
+ SSP0_D7 | VE_3_3V | PULLUP(1),
+ SSP0_CMD | VE_3_3V | PULLUP(1),
+ SSP0_CD | VE_3_3V | PULLUP(1),
+ SSP0_SCK | VE_3_3V | BITKEEPER(0),
+ /* MCI slot power control 1 = off */
+ PWM3_GPIO | VE_3_3V | GPIO_OUT | GPIO_VALUE(0),
+ /* MCI write protect 1 = not protected */
+ SSP1_SCK_GPIO | VE_3_3V | GPIO_IN,
+};
+
+static struct mxs_mci_platform_data mci_pdata = {
+ .caps = MMC_MODE_8BIT,
+ .voltages = MMC_VDD_32_33 | MMC_VDD_33_34, /* fixed to 3.3 V */
+ .f_min = 400 * 1000,
+ .f_max = 25000000,
+};
+
+/* fec */
+static void __init mx28_evk_fec_reset(void)
+{
+ mdelay(1);
+ gpio_set_value(MX28EVK_FEC_PHY_RESET_GPIO, 1);
+}
+
+/* PhyAD[0..2]=0, RMIISEL=1 */
+static struct fec_platform_data fec_info = {
+ .xcv_type = RMII,
+ .phy_addr = 0,
+};
+
+static int mx28_evk_mem_init(void)
+{
+ arm_add_mem_device("ram0", IMX_MEMORY_BASE, 128 * 1024 * 1024);
+
+ return 0;
+}
+mem_initcall(mx28_evk_mem_init);
+
+static int mx28_evk_devices_init(void)
+{
+ int i;
+
+ /* initizalize muxing */
+ for (i = 0; i < ARRAY_SIZE(mx28evk_pads); i++)
+ imx_gpio_mode(mx28evk_pads[i]);
+
+ /* enable IOCLK0 to run at the PLL frequency */
+ imx_set_ioclk(0, 480000000);
+ /* run the SSP unit clock at 100 MHz */
+ imx_set_sspclk(0, 100000000, 1);
+
+ armlinux_set_bootparams((void *)IMX_MEMORY_BASE + 0x100);
+ armlinux_set_architecture(MACH_TYPE_MX28EVK);
+
+ add_generic_device("mxs_mci", 0, NULL, IMX_SSP0_BASE, 0,
+ IORESOURCE_MEM, &mci_pdata);
+
+ imx_enable_enetclk();
+ mx28_evk_fec_reset();
+ add_generic_device("fec_imx", 0, NULL, IMX_FEC0_BASE, 0,
+ IORESOURCE_MEM, &fec_info);
+
+ return 0;
+}
+device_initcall(mx28_evk_devices_init);
+
+static int mx28_evk_console_init(void)
+{
+ add_generic_device("stm_serial", 0, NULL, IMX_DBGUART_BASE, 8192,
+ IORESOURCE_MEM, NULL);
+
+ return 0;
+}
+console_initcall(mx28_evk_console_init);
diff --git a/arch/arm/configs/imx28evk_defconfig b/arch/arm/configs/imx28evk_defconfig
new file mode 100644
index 0000000..1860aef
--- /dev/null
+++ b/arch/arm/configs/imx28evk_defconfig
@@ -0,0 +1,48 @@
+CONFIG_ARCH_MXS=y
+CONFIG_ARCH_IMX28=y
+CONFIG_MACH_MX28EVK=y
+CONFIG_AEABI=y
+CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
+CONFIG_MMU=y
+CONFIG_TEXT_BASE=0x43000000
+CONFIG_MALLOC_SIZE=0x800000
+CONFIG_BROKEN=y
+CONFIG_LONGHELP=y
+CONFIG_GLOB=y
+CONFIG_HUSH_FANCY_PROMPT=y
+CONFIG_CMDLINE_EDITING=y
+CONFIG_AUTO_COMPLETE=y
+CONFIG_PARTITION=y
+CONFIG_DEFAULT_ENVIRONMENT_GENERIC=y
+CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/freescale-mx28-evk/env"
+CONFIG_DEBUG_INFO=y
+CONFIG_CMD_EDIT=y
+CONFIG_CMD_SLEEP=y
+CONFIG_CMD_SAVEENV=y
+CONFIG_CMD_LOADENV=y
+CONFIG_CMD_EXPORT=y
+CONFIG_CMD_PRINTENV=y
+CONFIG_CMD_READLINE=y
+CONFIG_CMD_ECHO_E=y
+CONFIG_CMD_MTEST=y
+CONFIG_CMD_MTEST_ALTERNATIVE=y
+CONFIG_CMD_BOOTM_ZLIB=y
+CONFIG_CMD_BOOTM_BZLIB=y
+CONFIG_CMD_BOOTM_SHOW_TYPE=y
+CONFIG_CMD_RESET=y
+CONFIG_CMD_GO=y
+CONFIG_CMD_TIMEOUT=y
+CONFIG_CMD_PARTITION=y
+CONFIG_CMD_GPIO=y
+CONFIG_NET=y
+CONFIG_NET_DHCP=y
+CONFIG_NET_PING=y
+CONFIG_NET_TFTP=y
+CONFIG_NET_RESOLV=y
+CONFIG_DRIVER_NET_FEC_IMX=y
+# CONFIG_SPI is not set
+CONFIG_MCI=y
+CONFIG_MCI_STARTUP=y
+CONFIG_MCI_MXS=y
+CONFIG_FS_FAT=y
+CONFIG_FS_FAT_LFN=y
diff --git a/arch/arm/mach-mxs/Kconfig b/arch/arm/mach-mxs/Kconfig
index caef7e0..15f7c74 100644
--- a/arch/arm/mach-mxs/Kconfig
+++ b/arch/arm/mach-mxs/Kconfig
@@ -5,11 +5,13 @@ config ARCH_TEXT_BASE
default 0x41000000 if MACH_MX23EVK
default 0x42000000 if MACH_CHUMBY
default 0x47000000 if MACH_TX28
+ default 0x47000000 if MACH_MX28EVK
config BOARDINFO
default "Freescale i.MX23-EVK" if MACH_MX23EVK
default "Chumby Falconwing" if MACH_CHUMBY
default "Karo TX28" if MACH_TX28
+ default "Freescale i.MX28-EVK" if MACH_MX28EVK
comment "Freescale i.MX System-on-Chip"
@@ -57,6 +59,11 @@ config MACH_TX28
help
Say Y here if you are using the KARO TX28 CPU module.
+config MACH_MX28EVK
+ bool "mx28-evk"
+ help
+ Say Y here if you are using the Freescale i.MX28-EVK board
+
endchoice
endif
diff --git a/arch/arm/mach-mxs/include/mach/iomux-imx28.h b/arch/arm/mach-mxs/include/mach/iomux-imx28.h
index 1e6d421..1557126 100644
--- a/arch/arm/mach-mxs/include/mach/iomux-imx28.h
+++ b/arch/arm/mach-mxs/include/mach/iomux-imx28.h
@@ -302,6 +302,7 @@
#define PWM2 (FUNC(0) | PORTF(3, 18))
#define PWM1 (FUNC(0) | PORTF(3, 17))
+#define PWM1_DUART_TX (FUNC(2) | PORTF(3, 17))
#define PWM0 (FUNC(0) | PORTF(3, 16))
#define PWM0_I2C1_SCL (FUNC(1) | PORTF(3, 16))
--
1.7.7.3
More information about the barebox
mailing list