*** PROBABLY SPAM *** [PATCH v2 6/7] platform: add support for aizo dSS11
Jean-Christophe PLAGNIOL-VILLARD
plagnioj at jcrosoft.com
Fri Dec 9 10:01:31 EST 2011
On 12:29 Fri 09 Dec , Michael Grzeschik wrote:
> Signed-off-by: Michael Grzeschik <m.grzeschik at pengutronix.de>
> ---
> arch/arm/Makefile | 1 +
> arch/arm/boards/dss11/Makefile | 1 +
> arch/arm/boards/dss11/config.h | 6 ++
> arch/arm/boards/dss11/env/config | 42 ++++++++++
> arch/arm/boards/dss11/init.c | 156 ++++++++++++++++++++++++++++++++++++++
> arch/arm/mach-at91/Kconfig | 8 ++
> 6 files changed, 214 insertions(+), 0 deletions(-)
> create mode 100644 arch/arm/boards/dss11/Makefile
> create mode 100644 arch/arm/boards/dss11/config.h
> create mode 100644 arch/arm/boards/dss11/env/config
> create mode 100644 arch/arm/boards/dss11/init.c
>
> diff --git a/arch/arm/Makefile b/arch/arm/Makefile
> index 6f5f343..e5e951c 100644
> - removed GPL address
> - increased barebox and env partition size
> - changed boot partition on nand
> - removed lowlevel.S
> - fixed nand bus_width to 16
> - moved ethernet pin handling to another patch
> - touch mach-types from another patch
> - removed kernel and rootfs partitions
> --- a/arch/arm/Makefile
> +++ b/arch/arm/Makefile
> @@ -66,6 +66,7 @@ board-$(CONFIG_MACH_AT91SAM9263EK) := at91sam9263ek
> board-$(CONFIG_MACH_AT91SAM9G10EK) := at91sam9261ek
> board-$(CONFIG_MACH_AT91SAM9G20EK) := at91sam9260ek
> board-$(CONFIG_MACH_AT91SAM9M10G45EK) := at91sam9m10g45ek
> +board-$(CONFIG_MACH_DSS11) := dss11
> board-$(CONFIG_MACH_EDB9301) := edb93xx
> board-$(CONFIG_MACH_EDB9302) := edb93xx
> board-$(CONFIG_MACH_EDB9302A) := edb93xx
> diff --git a/arch/arm/boards/dss11/Makefile b/arch/arm/boards/dss11/Makefile
> new file mode 100644
> index 0000000..eb072c0
> --- /dev/null
> +++ b/arch/arm/boards/dss11/Makefile
> @@ -0,0 +1 @@
> +obj-y += init.o
> diff --git a/arch/arm/boards/dss11/config.h b/arch/arm/boards/dss11/config.h
> new file mode 100644
> index 0000000..006820c
> --- /dev/null
> +++ b/arch/arm/boards/dss11/config.h
> @@ -0,0 +1,6 @@
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +#define AT91_MAIN_CLOCK 18432000 /* 18.432 MHz crystal */
> +
> +#endif /* __CONFIG_H */
> diff --git a/arch/arm/boards/dss11/env/config b/arch/arm/boards/dss11/env/config
> new file mode 100644
> index 0000000..5c9be7d
> --- /dev/null
> +++ b/arch/arm/boards/dss11/env/config
> @@ -0,0 +1,42 @@
> +#!/bin/sh
> +
> +# use 'dhcp' to do dhcp in barebox and in kernel
> +# use 'none' if you want to skip kernel ip autoconfiguration
> +ip=dhcp
> +
> +# or set your networking parameters here
> +#eth0.ipaddr=a.b.c.d
> +#eth0.netmask=a.b.c.d
> +#eth0.gateway=a.b.c.d
> +#eth0.serverip=a.b.c.d
> +
> +# can be either 'nfs', 'tftp' or 'nand'
> +kernel_loc=tftp
> +# can be either 'net', 'nand' or 'initrd'
> +rootfs_loc=net
> +
> +# can be either 'jffs2' or 'ubifs'
> +rootfs_type=ubifs
> +rootfsimage=root.$rootfs_type
> +
> +# The image type of the kernel. Can be uimage, zimage, raw, or raw_lzo
> +#kernelimage_type=zimage
> +#kernelimage=zImage
> +kernelimage_type=uimage
> +kernelimage=uImage
> +#kernelimage_type=raw
> +#kernelimage=Image
> +#kernelimage_type=raw_lzo
> +#kernelimage=Image.lzo
> +
> +nand_device=atmel_nand
> +nand_parts="128k(bootstrap),512k(barebox)ro,512k(barebox-env),2M(kernel-rescue),2M(kernel-prod),32M(rootfs-rescue),200M(rootfs-prod),-(config)"
> +rootfs_mtdblock_nand=4
> +
> +autoboot_timeout=3
> +
> +bootargs="console=ttyS0,115200"
> +
> +# set a fancy prompt (if support is compiled in)
> +PS1="\e[1;32mbarebox@\e[1;31m\h:\w\e[0m "
> +
> diff --git a/arch/arm/boards/dss11/init.c b/arch/arm/boards/dss11/init.c
> new file mode 100644
> index 0000000..96c4eef
> --- /dev/null
> +++ b/arch/arm/boards/dss11/init.c
> @@ -0,0 +1,156 @@
> +/*
> + * Copyright (C) 2011 Michael Grzeschik <mgr at pengutronix.de>
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <common.h>
> +#include <net.h>
> +#include <mci.h>
> +#include <init.h>
> +#include <environment.h>
> +#include <fec.h>
> +#include <asm/armlinux.h>
> +#include <generated/mach-types.h>
> +#include <partition.h>
> +#include <fs.h>
> +#include <fcntl.h>
> +#include <asm/io.h>
> +#include <asm/hardware.h>
> +#include <nand.h>
> +#include <linux/mtd/nand.h>
> +#include <mach/board.h>
> +#include <mach/at91sam9_smc.h>
> +#include <mach/sam9_smc.h>
> +#include <gpio.h>
> +#include <mach/io.h>
> +#include <mach/at91_pmc.h>
> +#include <mach/at91_rstc.h>
> +
> +static struct atmel_nand_data nand_pdata = {
> + .ale = 21,
> + .cle = 22,
> +/* .det_pin = ... not connected */
please use -EINVAL
I'm going to apply the same cleanup on barebox that I did on the kernel
> + .ecc_mode = NAND_ECC_HW,
this will not work IIRC
the current implementation is bugged
I've to fix it in the kernel at least
> + .rdy_pin = AT91_PIN_PC13,
> + .enable_pin = AT91_PIN_PC14,
> + .bus_width_16 = 1,
> +};
> +
> +static struct sam9_smc_config dss11_nand_smc_config = {
> + .ncs_read_setup = 0,
> + .nrd_setup = 1,
> + .ncs_write_setup = 0,
> + .nwe_setup = 1,
> +
> + .ncs_read_pulse = 3,
> + .nrd_pulse = 3,
> + .ncs_write_pulse = 3,
> + .nwe_pulse = 3,
> +
> + .read_cycle = 5,
> + .write_cycle = 5,
> +
> + .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
> + .tdf_cycles = 2,
> +};
> +
> +static void dss11_add_device_nand(void)
> +{
> + /* setup bus-width (16) */
> + dss11_nand_smc_config.mode |= AT91_SMC_DBW_16;
put it directly in the struct to reduce the size
> +
> + /* configure chip-select 3 (NAND) */
> + sam9_smc_configure(3, &dss11_nand_smc_config);
> +
> + at91_add_device_nand(&nand_pdata);
> +}
> +
> +static struct at91_ether_platform_data macb_pdata = {
> + .phy_addr = 0,
> + .flags = AT91SAM_ETX2_ETX3_ALTERNATIVE,
> +};
> +
> +static void dss11_phy_reset(void)
> +{
> + unsigned long rstc;
> + at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9260_ID_EMAC);
> +
> + at91_set_gpio_input(AT91_PIN_PA14, 0);
> + at91_set_gpio_input(AT91_PIN_PA15, 0);
> + at91_set_gpio_input(AT91_PIN_PA17, 0);
> + at91_set_gpio_input(AT91_PIN_PA25, 0);
> + at91_set_gpio_input(AT91_PIN_PA26, 0);
> + at91_set_gpio_input(AT91_PIN_PA28, 0);
> +
> + rstc = at91_sys_read(AT91_RSTC_MR) & AT91_RSTC_ERSTL;
> +
> + /* Need to reset PHY -> 500ms reset */
> + at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
> + (AT91_RSTC_ERSTL & (0x0d << 8)) |
> + AT91_RSTC_URSTEN);
> +
> + at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_EXTRST);
> +
> + /* Wait for end hardware reset */
> + while (!(at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_NRSTL));
> +
> + /* Restore NRST value */
> + at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
> + (rstc) |
> + AT91_RSTC_URSTEN);
> +}
> +
> +static struct atmel_mci_platform_data dss11_mci_data = {
> + .bus_width = 4,
> + .host_caps = MMC_MODE_HS,
> +};
> +
> +static struct at91_usbh_data dss11_usbh_data = {
> + .ports = 2,
> +};
> +
> +static int dss11_mem_init(void)
> +{
> + at91_add_device_sdram(64 * 1024 * 1024);
> +
> + return 0;
> +}
> +mem_initcall(dss11_mem_init);
> +
> +static int dss11_devices_init(void)
> +{
> + dss11_add_device_nand();
> + dss11_phy_reset();
> + at91_add_device_eth(&macb_pdata);
> + at91_add_device_mci(1, &dss11_mci_data);
> + at91_add_device_usbh_ohci(&dss11_usbh_data);
> +
> + armlinux_set_bootparams((void *)(AT91_CHIPSELECT_1 + 0x100));
> + armlinux_set_architecture(MACH_TYPE_DSS11);
> +
> + devfs_add_partition("nand0", 0x00000, 0x20000, PARTITION_FIXED, "bootstrap");
> + dev_add_bb_dev("bootstrap", "bootstrap.bb");
> + devfs_add_partition("nand0", 0x20000, 0x40000, PARTITION_FIXED, "barebox");
> + dev_add_bb_dev("barebox", "barebox.bb");
> + devfs_add_partition("nand0", 0x60000, 0x40000, PARTITION_FIXED, "barebox-env");
> + dev_add_bb_dev("barebox-env", "env0");
> +
> + return 0;
> +}
> +device_initcall(dss11_devices_init);
> +
> +static int dss11_console_init(void)
> +{
> + at91_register_uart(0, 0);
> + return 0;
> +}
> +console_initcall(dss11_console_init);
> diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
> index 2ac23b5..e0e17bb 100644
> --- a/arch/arm/mach-at91/Kconfig
> +++ b/arch/arm/mach-at91/Kconfig
> @@ -20,6 +20,7 @@ config BOARDINFO
> default "Ronetix PM9261" if MACH_PM9261
> default "Ronetix PM9263" if MACH_PM9263
> default "Ronetix PM9G45" if MACH_PM9G45
> + default "Aizo dSS11" if MACH_DSS11
please keep it sort
>
> config HAVE_NAND_ATMEL_BUSWIDTH_16
> bool
> @@ -175,6 +176,13 @@ config MACH_USB_A9G20
> Select this if you are using a Calao Systems USB-A9G20.
> <http://www.calao-systems.com>
>
> +config MACH_DSS11
> + bool "aizo dSS11"
> + select HAVE_NAND_ATMEL_BUSWIDTH_16
> + help
> + Select this if you are using aizo dSS11
> + that embeds only one SD/MMC slot.
ditto
Best Regards,
J.
More information about the barebox
mailing list