[PATCH v4 4/4] arm64: dts: rk3399-pinephone-pro: Add internal display support
Ondřej Jirman
megi at xff.cz
Fri Dec 30 07:37:45 PST 2022
Hi Javier,
On Fri, Dec 30, 2022 at 12:31:54PM +0100, Javier Martinez Canillas wrote:
> From: Ondrej Jirman <megi at xff.cz>
>
> The phone's display is using Hannstar LCD panel, and Goodix based
> touchscreen. Support it.
>
> Signed-off-by: Ondrej Jirman <megi at xff.cz>
> Co-developed-by: Martijn Braam <martijn at brixit.nl>
> Signed-off-by: Martijn Braam <martijn at brixit.nl>
> Co-developed-by: Kamil Trzciński <ayufan at ayufan.eu>
> Signed-off-by: Kamil Trzciński <ayufan at ayufan.eu>
> Signed-off-by: Javier Martinez Canillas <javierm at redhat.com>
> Tested-by: Tom Fitzhenry <tom at tom-fitzhenry.me.uk>
> ---
>
> Changes in v4:
> - Add Tom Fitzhenry's Tested-by tag.
> - Keep the DTS nodes sorted alphabetically (Tom Fitzhenry).
>
> Changes in v2:
> - Fix regulator node names (Maya Matuszczyk).
> - Drop non-existent "poweroff-in-suspend" property (Maya Matuszczyk).
> - Remove unnecessary comments in panel node (Maya Matuszczyk).
>
> .../dts/rockchip/rk3399-pinephone-pro.dts | 123 ++++++++++++++++++
> 1 file changed, 123 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
> index 04403a76238b..0d48fbc5dbe4 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
> @@ -25,6 +25,12 @@ aliases {
> mmc2 = &sdhci;
> };
>
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm0 0 1000000 0>;
> + pwm-delay-us = <10000>;
> + };
> +
> chosen {
> stdout-path = "serial2:115200n8";
> };
> @@ -82,6 +88,32 @@ vcc1v8_codec: vcc1v8-codec-regulator {
> vin-supply = <&vcc3v3_sys>;
> };
>
> + /* MIPI DSI panel 1.8v supply */
> + vcc1v8_lcd: vcc1v8-lcd-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + regulator-name = "vcc1v8_lcd";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc3v3_sys>;
> + gpio = <&gpio3 RK_PA5 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&display_pwren1>;
> + };
> +
> + /* MIPI DSI panel 2.8v supply */
> + vcc2v8_lcd: vcc2v8-lcd-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + regulator-name = "vcc2v8_lcd";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + vin-supply = <&vcc3v3_sys>;
> + gpio = <&gpio3 RK_PA1 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&display_pwren>;
> + };
> +
> wifi_pwrseq: sdio-wifi-pwrseq {
> compatible = "mmc-pwrseq-simple";
> clocks = <&rk818 1>;
> @@ -132,6 +164,11 @@ &emmc_phy {
> status = "okay";
> };
>
> +&gpu {
> + mali-supply = <&vdd_gpu>;
> + status = "okay";
> +};
> +
> &i2c0 {
> clock-frequency = <400000>;
> i2c-scl-rising-time-ns = <168>;
> @@ -214,6 +251,9 @@ vcc3v0_touch: LDO_REG2 {
> regulator-name = "vcc3v0_touch";
> regulator-min-microvolt = <3000000>;
> regulator-max-microvolt = <3000000>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
You're instructing RK818 to shut down the regulator for touch controller during
suspend, but I think Goodix driver expects touch controller to be kept powered on
during suspend. Am I missing something?
https://elixir.bootlin.com/linux/latest/source/drivers/input/touchscreen/goodix.c#L1405
> };
>
> vcca1v8_codec: LDO_REG3 {
> @@ -347,6 +387,25 @@ opp07 {
> };
> };
>
> +&i2c3 {
> + i2c-scl-rising-time-ns = <450>;
> + i2c-scl-falling-time-ns = <15>;
> + status = "okay";
> +
> + touchscreen at 14 {
> + compatible = "goodix,gt917s";
This is not the correct compatible. Pinephone Pro uses Goodix GT1158:
Goodix-TS 3-0014: ID 1158, version: 0100
Goodix-TS 3-0014: Direct firmware load for goodix_1158_cfg.bin failed with error -2
> + reg = <0x14>;
> + interrupt-parent = <&gpio3>;
> + interrupts = <RK_PB5 IRQ_TYPE_EDGE_RISING>;
> + irq-gpios = <&gpio3 RK_PB5 GPIO_ACTIVE_HIGH>;
> + reset-gpios = <&gpio3 RK_PB4 GPIO_ACTIVE_HIGH>;
> + AVDD28-supply = <&vcc3v0_touch>;
> + VDDIO-supply = <&vcc3v0_touch>;
> + touchscreen-size-x = <720>;
> + touchscreen-size-y = <1440>;
> + };
> +};
> +
> &io_domains {
> bt656-supply = <&vcc1v8_dvp>;
> audio-supply = <&vcca1v8_codec>;
> @@ -355,6 +414,40 @@ &io_domains {
> status = "okay";
> };
>
> +&mipi_dsi {
> + status = "okay";
> + clock-master;
> +
> + ports {
> + mipi_out: port at 1 {
> + #address-cells = <0>;
> + #size-cells = <0>;
> + reg = <1>;
> +
> + mipi_out_panel: endpoint {
> + remote-endpoint = <&mipi_in_panel>;
> + };
> + };
> + };
> +
> + panel at 0 {
> + compatible = "hannstar,hsd060bhw4", "himax,hx8394";
> + reg = <0>;
> + backlight = <&backlight>;
> + reset-gpios = <&gpio4 RK_PD1 GPIO_ACTIVE_LOW>;
> + vcc-supply = <&vcc2v8_lcd>;
> + iovcc-supply = <&vcc1v8_lcd>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&display_rst_l>;
> +
> + port {
> + mipi_in_panel: endpoint {
> + remote-endpoint = <&mipi_out_panel>;
> + };
> + };
> + };
> +};
> +
> &pmu_io_domains {
> pmu1830-supply = <&vcc_1v8>;
> status = "okay";
> @@ -367,6 +460,20 @@ pwrbtn_pin: pwrbtn-pin {
> };
> };
>
> + dsi {
> + display_rst_l: display-rst-l {
> + rockchip,pins = <4 RK_PD1 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> +
> + display_pwren: display-pwren {
> + rockchip,pins = <3 RK_PA1 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> +
> + display_pwren1: display-pwren1 {
> + rockchip,pins = <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +
> pmic {
> pmic_int_l: pmic-int-l {
> rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
> @@ -408,6 +515,10 @@ bt_reset_pin: bt-reset-pin {
> };
> };
>
> +&pwm0 {
> + status = "okay";
> +};
> +
> &sdio0 {
> bus-width = <4>;
> cap-sd-highspeed;
> @@ -472,3 +583,15 @@ bluetooth {
> &uart2 {
> status = "okay";
> };
> +
> +&vopb {
> + status = "okay";
> + assigned-clocks = <&cru DCLK_VOP0_DIV>, <&cru DCLK_VOP0>,
> + <&cru ACLK_VOP0>, <&cru HCLK_VOP0>;
> + assigned-clock-rates = <0>, <0>, <400000000>, <100000000>;
> + assigned-clock-parents = <&cru PLL_CPLL>, <&cru DCLK_VOP0_FRAC>;
> +};
So here you're putting a fractional clock into path between CPLL -> VOP0_DIV
-> DCLK_VOP0_FRAC -> DCLK_VOP0.
Fractional clocks require 20x difference between input and output rates, and
CPLL is 800Mhz IIRC, while you require 74.25MHz DCLK, so this will not work
correctly.
Even if this somehow works by fractional clock being bypassed, I did not design
the panel mode to be used with CPLL's 800 MHz, but with GPLL frequecy of 594 MHz.
GPLL 594/74.25 = 8 (integral divider without the need for fractional clock)
CPLL 800/74.25 = ~10.77441077441077441077
If you really want to use fractional clock, you'd need to parent it to VPLL
and set VPLL really high, like close to 2GHz.
kind regards,
o.
> +&vopb_mmu {
> + status = "okay";
> +};
> --
> 2.38.1
>
More information about the Linux-rockchip
mailing list