[PATCH 1/2] regulator: rk808: add dvs support
Chris Zhong
zyw at rock-chips.com
Tue Dec 9 05:51:45 PST 2014
rk808 has a dvs function, there are 3 pins for dvs, dvs1 & dvs2 & dvsok.
Normally, the voltage of DCDC1/DCDC2 are controlled by BUCKn_ON_VSEL, when
we pull dvs1/dvs2 pin to active, they would be controlled by BUCKn_DVS_VSEL.
And the dvsok pin is used to indicate whether regulating has been completed.
When dvs1/dvs2 pin change, dvsok would be pull down, and it would be pull up
once the regulating is complete.
Signed-off-by: Chris Zhong <zyw at rock-chips.com>
---
drivers/regulator/rk808-regulator.c | 192 +++++++++++++++++++++++++++++++++---
1 file changed, 180 insertions(+), 12 deletions(-)
diff --git a/drivers/regulator/rk808-regulator.c b/drivers/regulator/rk808-regulator.c
index c94a3e0..f415188 100644
--- a/drivers/regulator/rk808-regulator.c
+++ b/drivers/regulator/rk808-regulator.c
@@ -16,10 +16,13 @@
* more details.
*/
-#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
#include <linux/i2c.h>
-#include <linux/mfd/rk808.h>
+#include <linux/module.h>
#include <linux/of_device.h>
+#include <linux/of_gpio.h>
+#include <linux/mfd/rk808.h>
#include <linux/regulator/driver.h>
#include <linux/regulator/of_regulator.h>
@@ -36,12 +39,23 @@
#define RK808_RAMP_RATE_6MV_PER_US (2 << RK808_RAMP_RATE_OFFSET)
#define RK808_RAMP_RATE_10MV_PER_US (3 << RK808_RAMP_RATE_OFFSET)
+#define RK808_DVS2_POL BIT(2)
+#define RK808_DVS1_POL BIT(1)
+
/* Offset from XXX_ON_VSEL to XXX_SLP_VSEL */
#define RK808_SLP_REG_OFFSET 1
+/* Offset from XXX_ON_VSEL to XXX_DVS_VSEL */
+#define RK808_DVS_REG_OFFSET 2
+
/* Offset from XXX_EN_REG to SLEEP_SET_OFF_XXX */
#define RK808_SLP_SET_OFF_REG_OFFSET 2
+struct rk808_regulator_data {
+ struct gpio_desc *dvsok_gpio;
+ struct gpio_desc *dvs_gpio[2];
+};
+
static const int rk808_buck_config_regs[] = {
RK808_BUCK1_CONFIG_REG,
RK808_BUCK2_CONFIG_REG,
@@ -70,6 +84,96 @@ static const struct regulator_linear_range rk808_ldo6_voltage_ranges[] = {
REGULATOR_LINEAR_RANGE(800000, 0, 17, 100000),
};
+int rk808_buck1_2_get_voltage_sel_regmap(struct regulator_dev *rdev)
+{
+ struct rk808_regulator_data *pdata = rdev_get_drvdata(rdev);
+ int id = rdev->desc->id - RK808_ID_DCDC1;
+ struct gpio_desc *gpio = pdata->dvs_gpio[id];
+ unsigned int val;
+ int ret;
+
+ if (IS_ERR(gpio) || gpiod_get_value(gpio) == 0)
+ return regulator_get_voltage_sel_regmap(rdev);
+
+ ret = regmap_read(rdev->regmap,
+ rdev->desc->vsel_reg + RK808_DVS_REG_OFFSET,
+ &val);
+ if (ret != 0)
+ return ret;
+
+ val &= rdev->desc->vsel_mask;
+ val >>= ffs(rdev->desc->vsel_mask) - 1;
+
+ return val;
+}
+
+int rk808_buck1_2_set_voltage_sel(struct regulator_dev *rdev, unsigned sel)
+{
+ struct rk808_regulator_data *pdata = rdev_get_drvdata(rdev);
+ int id = rdev->desc->id - RK808_ID_DCDC1;
+ struct gpio_desc *gpio = pdata->dvs_gpio[id];
+ unsigned int reg = rdev->desc->vsel_reg;
+ unsigned long timeout;
+ unsigned old_sel;
+ int ret, gpio_level;
+
+ if (IS_ERR(gpio))
+ return regulator_set_voltage_sel_regmap(rdev, sel);
+
+ gpio_level = gpiod_get_value(gpio);
+ if (gpio_level == 0) {
+ reg += RK808_DVS_REG_OFFSET;
+ ret = regmap_read(rdev->regmap, rdev->desc->vsel_reg, &old_sel);
+ } else {
+ ret = regmap_read(rdev->regmap,
+ reg + RK808_DVS_REG_OFFSET,
+ &old_sel);
+ }
+
+ if (ret != 0)
+ return ret;
+
+ sel <<= ffs(rdev->desc->vsel_mask) - 1;
+ sel |= old_sel & ~rdev->desc->vsel_mask;
+
+ ret = regmap_write(rdev->regmap, reg, sel);
+ if (ret)
+ return ret;
+
+ gpiod_set_value(gpio, !gpio_level);
+
+ /* dvsok pin would be pull down when dvs1/2 pin changed, and
+ * it would be pull up once the voltage regulate complete.
+ * No need to wait dvsok signal when voltage falling.
+ */
+ if (old_sel < sel && !IS_ERR(pdata->dvsok_gpio)) {
+ timeout = jiffies + msecs_to_jiffies(1);
+ while (!time_after(jiffies, timeout)) {
+ udelay(1);
+ if (gpiod_get_value(pdata->dvsok_gpio))
+ return 0;
+ }
+ gpiod_set_value(gpio, gpio_level);
+ pr_err("%s wait dvsok timeout\n", rdev->desc->name);
+ ret = -EBUSY;
+ }
+
+ return ret;
+}
+
+int rk808_buck1_2_set_voltage_time_sel(struct regulator_dev *rdev,
+ unsigned int old_selector,
+ unsigned int new_selector)
+{
+ struct rk808_regulator_data *pdata = rdev_get_drvdata(rdev);
+
+ /* if there is a dvsok pin, we don't need wait extra time here */
+ if (!IS_ERR(pdata->dvsok_gpio))
+ return 0;
+
+ return regulator_set_voltage_time_sel(rdev, old_selector, new_selector);
+}
+
static int rk808_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay)
{
unsigned int ramp_value = RK808_RAMP_RATE_10MV_PER_US;
@@ -137,8 +241,9 @@ int rk808_set_suspend_disable(struct regulator_dev *rdev)
static struct regulator_ops rk808_buck1_2_ops = {
.list_voltage = regulator_list_voltage_linear_range,
.map_voltage = regulator_map_voltage_linear_range,
- .get_voltage_sel = regulator_get_voltage_sel_regmap,
- .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = rk808_buck1_2_get_voltage_sel_regmap,
+ .set_voltage_sel = rk808_buck1_2_set_voltage_sel,
+ .set_voltage_time_sel = rk808_buck1_2_set_voltage_time_sel,
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
.is_enabled = regulator_is_enabled_regmap,
@@ -372,25 +477,71 @@ static struct of_regulator_match rk808_reg_matches[] = {
[RK808_ID_SWITCH2] = { .name = "SWITCH_REG2" },
};
+int rk808_regulator_dt_parse_pdata(struct device *dev,
+ struct device *client_dev,
+ struct regmap *map,
+ struct rk808_regulator_data *pdata)
+{
+ struct device_node *np;
+ int tmp, ret, i;
+
+ np = of_get_child_by_name(client_dev->of_node, "regulators");
+ if (!np)
+ return -ENXIO;
+
+ ret = of_regulator_match(dev, np, rk808_reg_matches,
+ RK808_NUM_REGULATORS);
+ if (ret < 0)
+ goto dt_parse_end;
+
+ for (i = 0; i < ARRAY_SIZE(pdata->dvs_gpio); i++) {
+ pdata->dvs_gpio[i] = gpiod_get_index(client_dev, "dvs", i);
+ if (IS_ERR(pdata->dvs_gpio[i])) {
+ dev_warn(dev, "there is no dvs%d gpio\n", i);
+ continue;
+ }
+
+ gpiod_direction_output(pdata->dvs_gpio[i], 0);
+
+ tmp = i ? RK808_DVS2_POL : RK808_DVS1_POL;
+ ret = regmap_update_bits(map, RK808_IO_POL_REG, tmp,
+ gpiod_is_active_low(pdata->dvs_gpio[i]) ?
+ 0 : tmp);
+ }
+
+ pdata->dvsok_gpio = gpiod_get_index(client_dev, "dvsok", 0);
+ if (IS_ERR(pdata->dvsok_gpio)) {
+ dev_warn(dev, "there is no dvs ok gpio\n");
+ goto dt_parse_end;
+ }
+
+ gpiod_direction_input(pdata->dvsok_gpio);
+
+dt_parse_end:
+ of_node_put(np);
+ return ret;
+}
+
static int rk808_regulator_probe(struct platform_device *pdev)
{
struct rk808 *rk808 = dev_get_drvdata(pdev->dev.parent);
struct i2c_client *client = rk808->i2c;
- struct device_node *reg_np;
struct regulator_config config = {};
struct regulator_dev *rk808_rdev;
+ struct rk808_regulator_data *pdata;
int ret, i;
- reg_np = of_get_child_by_name(client->dev.of_node, "regulators");
- if (!reg_np)
- return -ENXIO;
+ pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+ if (!pdata)
+ return -ENOMEM;
- ret = of_regulator_match(&pdev->dev, reg_np, rk808_reg_matches,
- RK808_NUM_REGULATORS);
- of_node_put(reg_np);
+ ret = rk808_regulator_dt_parse_pdata(&pdev->dev, &client->dev,
+ rk808->regmap, pdata);
if (ret < 0)
return ret;
+ platform_set_drvdata(pdev, pdata);
+
/* Instantiate the regulators */
for (i = 0; i < RK808_NUM_REGULATORS; i++) {
if (!rk808_reg_matches[i].init_data ||
@@ -398,7 +549,7 @@ static int rk808_regulator_probe(struct platform_device *pdev)
continue;
config.dev = &client->dev;
- config.driver_data = rk808;
+ config.driver_data = pdata;
config.regmap = rk808->regmap;
config.of_node = rk808_reg_matches[i].of_node;
config.init_data = rk808_reg_matches[i].init_data;
@@ -415,10 +566,27 @@ static int rk808_regulator_probe(struct platform_device *pdev)
return 0;
}
+static int rk808_regulator_remove(struct platform_device *pdev)
+{
+ struct rk808_regulator_data *pdata = platform_get_drvdata(pdev);
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(pdata->dvs_gpio); i++) {
+ if (!IS_ERR(pdata->dvs_gpio[i]))
+ gpiod_put(pdata->dvs_gpio[i]);
+ }
+
+ if (!IS_ERR(pdata->dvsok_gpio))
+ gpiod_put(pdata->dvsok_gpio);
+ return 0;
+}
+
static struct platform_driver rk808_regulator_driver = {
.probe = rk808_regulator_probe,
+ .remove = rk808_regulator_remove,
.driver = {
.name = "rk808-regulator",
+ .owner = THIS_MODULE,
},
};
--
1.9.1
More information about the Linux-rockchip
mailing list