[PATCH v1 0/2] Add ethernet nodes for StarFive JH7110 SoC

[Guo Samin]

-------- 原始信息 --------
主题: Re: [PATCH v1 0/2] Add ethernet nodes for StarFive JH7110 SoC
From: Conor Dooley <conor at kernel.org>
收件人: Guo Samin <samin.guo at starfivetech.com>, Rob Herring <robh+dt at kernel.org>, Krzysztof Kozlowski <krzysztof.kozlowski+dt at linaro.org>, Paul Walmsley <paul.walmsley at sifive.com>, Palmer Dabbelt <palmer at dabbelt.com>, Albert Ou <aou at eecs.berkeley.edu>, Hal Feng <hal.feng at starfivetech.com>, linux-kernel at vger.kernel.org, linux-riscv at lists.infradead.org, devicetree at vger.kernel.org, netdev at vger.kernel.org
日期: 2023/7/21

> 
> 
> On 21 July 2023 03:09:19 IST, Guo Samin <samin.guo at starfivetech.com> wrote:
>>
>>
>> -------- 原始信息 --------
>> 主题: Re: [PATCH v1 0/2] Add ethernet nodes for StarFive JH7110 SoC
>> From: Conor Dooley <conor at kernel.org>
>> 收件人: Conor Dooley <conor at kernel.org>, Rob Herring <robh+dt at kernel.org>, Krzysztof Kozlowski <krzysztof.kozlowski+dt at linaro.org>, Paul Walmsley <paul.walmsley at sifive.com>, Palmer Dabbelt <palmer at dabbelt.com>, Albert Ou <aou at eecs.berkeley.edu>, Hal Feng <hal.feng at starfivetech.com>, linux-kernel at vger.kernel.org, linux-riscv at lists.infradead.org, devicetree at vger.kernel.org, netdev at vger.kernel.org, Samin Guo <samin.guo at starfivetech.com>
>> 日期: 2023/7/21
>>
>>> From: Conor Dooley <conor.dooley at microchip.com>
>>>
>>> On Fri, 14 Jul 2023 18:45:19 +0800, Samin Guo wrote:
>>>> This series adds ethernet nodes for StarFive JH7110 RISC-V SoC,
>>>> and has been tested on StarFive VisionFive-2 v1.2A and v1.3B SBC boards.
>>>>
>>>> The first patch adds ethernet nodes for jh7110 SoC, the second patch
>>>> adds ethernet nodes for visionfive 2 SBCs.
>>>>
>>>> This series relies on xingyu's syscon patch[1].
>>>> For more information and support, you can visit RVspace wiki[2].
>>>>
>>>> [...]
>>>
>>> Applied to riscv-dt-for-next, thanks!
>>>
>>> [1/2] riscv: dts: starfive: jh7110: Add ethernet device nodes
>>>       https://git.kernel.org/conor/c/1ff166c97972
>>> [2/2] riscv: dts: starfive: visionfive 2: Add configuration of gmac and phy
>>>       https://git.kernel.org/conor/c/b15a73c358d1
>>>
>>> Thanks,
>>> Conor.
>>
>>
>> Hi Conor，
>>
>> Thank you so much！ 
>>
>> There is a question about the configuration of phy that I would like to consult you.
>>
>> Latest on motorcomm PHY V5[1]: Follow Rob Herring's advice
>> motorcomm,rx-xxx-driver-strength Changed to motorcomm,rx-xxx-drv-microamp .
>> V5 has already received a reviewed-by from Andrew Lunn, and it should not change again.
>>
>> Should I submit another pacthes based on riscv-dt-for-next? 
> 
> Huh, dtbs_check passed for these patches,
> I didn't realise changes to the motorcomm stuff
> were a dep. for this. I'll take a look later.
>
Hi Conor,

Thanks for taking the time to follow this.

After discussing with HAL, I have prepared the code and considered adding the following patch to 
Motorcomm's patchsetes v6. (To fix some spelling errors in v5[1])
which will then send patches based on linux-next. What do you think? @Andrew @Conor

[1] https://patchwork.kernel.org/project/netdevbpf/cover/20230720111509.21843-1-samin.guo@starfivetech.com



--- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.3b.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.3b.dts
@@ -28,8 +28,8 @@
        motorcomm,tx-clk-adj-enabled;
        motorcomm,tx-clk-100-inverted;
        motorcomm,tx-clk-1000-inverted;
-       motorcomm,rx-clk-driver-strength = <3970>;
-       motorcomm,rx-data-driver-strength = <2910>;
+       motorcomm,rx-clk-drv-microamp = <3970>;
+       motorcomm,rx-data-drv-microamp = <2910>;
        rx-internal-delay-ps = <1500>;
        tx-internal-delay-ps = <1500>;
 };
@@ -37,8 +37,8 @@
 &phy1 {
        motorcomm,tx-clk-adj-enabled;
        motorcomm,tx-clk-100-inverted;
-       motorcomm,rx-clk-driver-strength = <3970>;
-       motorcomm,rx-data-driver-strength = <2910>;
+       motorcomm,rx-clk-drv-microamp = <3970>;
+       motorcomm,rx-data-drv-microamp = <2910>;
        rx-internal-delay-ps = <300>;
        tx-internal-delay-ps = <0>;
 };


Best regards,
Samin

>>
>> [1] https://patchwork.kernel.org/project/netdevbpf/cover/20230720111509.21843-1-samin.guo@starfivetech.com
>>
>>
>> Best regards,
>> Samin