[PATCH v3 2/5] dt-bindings: pinctrl: Add StarFive JH7110 sys pinctrl
Rob Herring
robh at kernel.org
Tue Dec 20 12:19:20 PST 2022
On Tue, Dec 20, 2022 at 08:55:26AM +0800, Hal Feng wrote:
> From: Jianlong Huang <jianlong.huang at starfivetech.com>
>
> Add pinctrl bindings for StarFive JH7110 SoC sys pinctrl controller.
>
> Signed-off-by: Jianlong Huang <jianlong.huang at starfivetech.com>
> Co-developed-by: Emil Renner Berthing <kernel at esmil.dk>
> Signed-off-by: Emil Renner Berthing <kernel at esmil.dk>
> Signed-off-by: Hal Feng <hal.feng at starfivetech.com>
> ---
> .../pinctrl/starfive,jh7110-sys-pinctrl.yaml | 142 ++++++++++++++++++
> MAINTAINERS | 3 +-
> .../pinctrl/starfive,jh7110-pinctrl.h | 115 ++++++++++++++
> 3 files changed, 259 insertions(+), 1 deletion(-)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
> create mode 100644 include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
> new file mode 100644
> index 000000000000..60e616af2201
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
> @@ -0,0 +1,142 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/starfive,jh7110-sys-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: StarFive JH7110 Sys Pin Controller
> +
> +description: |
> + Bindings for the JH7110 RISC-V SoC from StarFive Technology Ltd.
> +
> + Out of the SoC's many pins only the ones named PAD_GPIO0 to PAD_GPIO63
> + can be multiplexed and have configurable bias, drive strength,
> + schmitt trigger etc.
> + Some peripherals have their I/O go through the 64 "GPIOs". This also
> + includes a number of other UARTs, I2Cs, SPIs, PWMs etc.
> + All these peripherals are connected to all 64 GPIOs such that
> + any GPIO can be set up to be controlled by any of the peripherals.
> +
> +maintainers:
> + - Jianlong Huang <jianlong.huang at starfivetech.com>
> +
> +properties:
> + compatible:
> + const: starfive,jh7110-sys-pinctrl
> +
> + reg:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 1
> +
> + resets:
> + maxItems: 1
> +
> + interrupts:
> + maxItems: 1
> +
> + interrupt-controller: true
> +
> + '#interrupt-cells':
> + const: 2
> +
> + gpio-controller: true
> +
> + '#gpio-cells':
> + const: 2
> +
> +patternProperties:
> + '-[0-9]+$':
> + type: object
> + patternProperties:
> + '-pins$':
> + type: object
> + description: |
> + A pinctrl node should contain at least one subnode representing the
> + pinctrl groups available on the machine. Each subnode will list the
> + pins it needs, and how they should be configured, with regard to
> + muxer configuration, system signal configuration, pin groups for
> + vin/vout module, pin voltage, mux functions for output, mux functions
> + for output enable, mux functions for input.
> +
> + properties:
> + pinmux:
> + description: |
> + The list of GPIOs and their mux settings that properties in the
> + node apply to. This should be set using the GPIOMUX macro.
> + $ref: /schemas/pinctrl/pinmux-node.yaml#/properties/pinmux
Generally, don't reference individual properties. Instead, '-pins$'
needs a $ref to pinmux-node.yaml.
> +
> + bias-disable: true
> +
> + bias-pull-up:
> + type: boolean
> +
> + bias-pull-down:
> + type: boolean
> +
> + drive-strength:
> + enum: [ 2, 4, 8, 12 ]
> +
> + input-enable: true
> +
> + input-disable: true
> +
> + input-schmitt-enable: true
> +
> + input-schmitt-disable: true
> +
> + slew-rate:
> + maximum: 1
> +
> + additionalProperties: false
> +
> + additionalProperties: false
It's easier to read if you put these at the beginning before a long
properties section.
> +
> +required:
> + - compatible
> + - reg
> + - clocks
> + - interrupts
> + - interrupt-controller
> + - '#interrupt-cells'
> + - gpio-controller
> + - '#gpio-cells'
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + gpio at 13040000 {
> + compatible = "starfive,jh7110-sys-pinctrl";
> + reg = <0x13040000 0x10000>;
> + clocks = <&syscrg 112>;
> + resets = <&syscrg 2>;
> + interrupts = <86>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + uart0-0 {
> + tx-pins {
> + pinmux = <0xff140005>;
> + bias-disable;
> + drive-strength = <12>;
> + input-disable;
> + input-schmitt-disable;
> + slew-rate = <0>;
> + };
> +
> + rx-pins {
> + pinmux = <0x0E000406>;
> + bias-pull-up;
> + drive-strength = <2>;
> + input-enable;
> + input-schmitt-enable;
> + slew-rate = <0>;
> + };
> + };
> + };
> +
> +...
> diff --git a/MAINTAINERS b/MAINTAINERS
> index e0ffe584030b..57fd051ff4e8 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -19645,10 +19645,11 @@ M: Emil Renner Berthing <kernel at esmil.dk>
> M: Jianlong Huang <jianlong.huang at starfivetech.com>
> L: linux-gpio at vger.kernel.org
> S: Maintained
> -F: Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml
> +F: Documentation/devicetree/bindings/pinctrl/starfive,jh71*.yaml
> F: arch/riscv/boot/dts/starfive/jh7110-pinfunc.h
> F: drivers/pinctrl/starfive/
> F: include/dt-bindings/pinctrl/pinctrl-starfive-jh7100.h
> +F: include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h
>
> STARFIVE JH71X0 RESET CONTROLLER DRIVERS
> M: Emil Renner Berthing <kernel at esmil.dk>
> diff --git a/include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h b/include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h
> new file mode 100644
> index 000000000000..c97dde8e864c
> --- /dev/null
> +++ b/include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h
> @@ -0,0 +1,115 @@
> +/* SPDX-License-Identifier: GPL-2.0 OR MIT */
> +/*
> + * Copyright (C) 2022 Emil Renner Berthing <kernel at esmil.dk>
> + * Copyright (C) 2022 StarFive Technology Co., Ltd.
> + */
> +
> +#ifndef __DT_BINDINGS_PINCTRL_STARFIVE_JH7110_H__
> +#define __DT_BINDINGS_PINCTRL_STARFIVE_JH7110_H__
> +
> +/* sys_iomux pin */
> +#define PAD_GPIO0 0
> +#define PAD_GPIO1 1
> +#define PAD_GPIO2 2
> +#define PAD_GPIO3 3
> +#define PAD_GPIO4 4
> +#define PAD_GPIO5 5
> +#define PAD_GPIO6 6
> +#define PAD_GPIO7 7
> +#define PAD_GPIO8 8
> +#define PAD_GPIO9 9
> +#define PAD_GPIO10 10
> +#define PAD_GPIO11 11
> +#define PAD_GPIO12 12
> +#define PAD_GPIO13 13
> +#define PAD_GPIO14 14
> +#define PAD_GPIO15 15
> +#define PAD_GPIO16 16
> +#define PAD_GPIO17 17
> +#define PAD_GPIO18 18
> +#define PAD_GPIO19 19
> +#define PAD_GPIO20 20
> +#define PAD_GPIO21 21
> +#define PAD_GPIO22 22
> +#define PAD_GPIO23 23
> +#define PAD_GPIO24 24
> +#define PAD_GPIO25 25
> +#define PAD_GPIO26 26
> +#define PAD_GPIO27 27
> +#define PAD_GPIO28 28
> +#define PAD_GPIO29 29
> +#define PAD_GPIO30 30
> +#define PAD_GPIO31 31
> +#define PAD_GPIO32 32
> +#define PAD_GPIO33 33
> +#define PAD_GPIO34 34
> +#define PAD_GPIO35 35
> +#define PAD_GPIO36 36
> +#define PAD_GPIO37 37
> +#define PAD_GPIO38 38
> +#define PAD_GPIO39 39
> +#define PAD_GPIO40 40
> +#define PAD_GPIO41 41
> +#define PAD_GPIO42 42
> +#define PAD_GPIO43 43
> +#define PAD_GPIO44 44
> +#define PAD_GPIO45 45
> +#define PAD_GPIO46 46
> +#define PAD_GPIO47 47
> +#define PAD_GPIO48 48
> +#define PAD_GPIO49 49
> +#define PAD_GPIO50 50
> +#define PAD_GPIO51 51
> +#define PAD_GPIO52 52
> +#define PAD_GPIO53 53
> +#define PAD_GPIO54 54
> +#define PAD_GPIO55 55
> +#define PAD_GPIO56 56
> +#define PAD_GPIO57 57
> +#define PAD_GPIO58 58
> +#define PAD_GPIO59 59
> +#define PAD_GPIO60 60
> +#define PAD_GPIO61 61
> +#define PAD_GPIO62 62
> +#define PAD_GPIO63 63
> +#define PAD_SD0_CLK 64
> +#define PAD_SD0_CMD 65
> +#define PAD_SD0_DATA0 66
> +#define PAD_SD0_DATA1 67
> +#define PAD_SD0_DATA2 68
> +#define PAD_SD0_DATA3 69
> +#define PAD_SD0_DATA4 70
> +#define PAD_SD0_DATA5 71
> +#define PAD_SD0_DATA6 72
> +#define PAD_SD0_DATA7 73
> +#define PAD_SD0_STRB 74
> +#define PAD_GMAC1_MDC 75
> +#define PAD_GMAC1_MDIO 76
> +#define PAD_GMAC1_RXD0 77
> +#define PAD_GMAC1_RXD1 78
> +#define PAD_GMAC1_RXD2 79
> +#define PAD_GMAC1_RXD3 80
> +#define PAD_GMAC1_RXDV 81
> +#define PAD_GMAC1_RXC 82
> +#define PAD_GMAC1_TXD0 83
> +#define PAD_GMAC1_TXD1 84
> +#define PAD_GMAC1_TXD2 85
> +#define PAD_GMAC1_TXD3 86
> +#define PAD_GMAC1_TXEN 87
> +#define PAD_GMAC1_TXC 88
> +#define PAD_QSPI_SCLK 89
> +#define PAD_QSPI_CS0 90
> +#define PAD_QSPI_DATA0 91
> +#define PAD_QSPI_DATA1 92
> +#define PAD_QSPI_DATA2 93
> +#define PAD_QSPI_DATA3 94
> +
> +#define GPOUT_LOW 0
> +#define GPOUT_HIGH 1
> +
> +#define GPOEN_ENABLE 0
> +#define GPOEN_DISABLE 1
> +
> +#define GPI_NONE 255
> +
> +#endif
> --
> 2.38.1
>
>
More information about the linux-riscv
mailing list