[PATCH v3 2/5] dt-bindings: pinctrl: Add StarFive JH7110 sys pinctrl
Hal Feng
hal.feng at starfivetech.com
Mon Dec 19 16:55:26 PST 2022
From: Jianlong Huang <jianlong.huang at starfivetech.com>
Add pinctrl bindings for StarFive JH7110 SoC sys pinctrl controller.
Signed-off-by: Jianlong Huang <jianlong.huang at starfivetech.com>
Co-developed-by: Emil Renner Berthing <kernel at esmil.dk>
Signed-off-by: Emil Renner Berthing <kernel at esmil.dk>
Signed-off-by: Hal Feng <hal.feng at starfivetech.com>
---
.../pinctrl/starfive,jh7110-sys-pinctrl.yaml | 142 ++++++++++++++++++
MAINTAINERS | 3 +-
.../pinctrl/starfive,jh7110-pinctrl.h | 115 ++++++++++++++
3 files changed, 259 insertions(+), 1 deletion(-)
create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
create mode 100644 include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h
diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
new file mode 100644
index 000000000000..60e616af2201
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
@@ -0,0 +1,142 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jh7110-sys-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH7110 Sys Pin Controller
+
+description: |
+ Bindings for the JH7110 RISC-V SoC from StarFive Technology Ltd.
+
+ Out of the SoC's many pins only the ones named PAD_GPIO0 to PAD_GPIO63
+ can be multiplexed and have configurable bias, drive strength,
+ schmitt trigger etc.
+ Some peripherals have their I/O go through the 64 "GPIOs". This also
+ includes a number of other UARTs, I2Cs, SPIs, PWMs etc.
+ All these peripherals are connected to all 64 GPIOs such that
+ any GPIO can be set up to be controlled by any of the peripherals.
+
+maintainers:
+ - Jianlong Huang <jianlong.huang at starfivetech.com>
+
+properties:
+ compatible:
+ const: starfive,jh7110-sys-pinctrl
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ const: 2
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 2
+
+patternProperties:
+ '-[0-9]+$':
+ type: object
+ patternProperties:
+ '-pins$':
+ type: object
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available on the machine. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to
+ muxer configuration, system signal configuration, pin groups for
+ vin/vout module, pin voltage, mux functions for output, mux functions
+ for output enable, mux functions for input.
+
+ properties:
+ pinmux:
+ description: |
+ The list of GPIOs and their mux settings that properties in the
+ node apply to. This should be set using the GPIOMUX macro.
+ $ref: /schemas/pinctrl/pinmux-node.yaml#/properties/pinmux
+
+ bias-disable: true
+
+ bias-pull-up:
+ type: boolean
+
+ bias-pull-down:
+ type: boolean
+
+ drive-strength:
+ enum: [ 2, 4, 8, 12 ]
+
+ input-enable: true
+
+ input-disable: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ slew-rate:
+ maximum: 1
+
+ additionalProperties: false
+
+ additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - interrupts
+ - interrupt-controller
+ - '#interrupt-cells'
+ - gpio-controller
+ - '#gpio-cells'
+
+additionalProperties: false
+
+examples:
+ - |
+ gpio at 13040000 {
+ compatible = "starfive,jh7110-sys-pinctrl";
+ reg = <0x13040000 0x10000>;
+ clocks = <&syscrg 112>;
+ resets = <&syscrg 2>;
+ interrupts = <86>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ uart0-0 {
+ tx-pins {
+ pinmux = <0xff140005>;
+ bias-disable;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+
+ rx-pins {
+ pinmux = <0x0E000406>;
+ bias-pull-up;
+ drive-strength = <2>;
+ input-enable;
+ input-schmitt-enable;
+ slew-rate = <0>;
+ };
+ };
+ };
+
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index e0ffe584030b..57fd051ff4e8 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -19645,10 +19645,11 @@ M: Emil Renner Berthing <kernel at esmil.dk>
M: Jianlong Huang <jianlong.huang at starfivetech.com>
L: linux-gpio at vger.kernel.org
S: Maintained
-F: Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml
+F: Documentation/devicetree/bindings/pinctrl/starfive,jh71*.yaml
F: arch/riscv/boot/dts/starfive/jh7110-pinfunc.h
F: drivers/pinctrl/starfive/
F: include/dt-bindings/pinctrl/pinctrl-starfive-jh7100.h
+F: include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h
STARFIVE JH71X0 RESET CONTROLLER DRIVERS
M: Emil Renner Berthing <kernel at esmil.dk>
diff --git a/include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h b/include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h
new file mode 100644
index 000000000000..c97dde8e864c
--- /dev/null
+++ b/include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h
@@ -0,0 +1,115 @@
+/* SPDX-License-Identifier: GPL-2.0 OR MIT */
+/*
+ * Copyright (C) 2022 Emil Renner Berthing <kernel at esmil.dk>
+ * Copyright (C) 2022 StarFive Technology Co., Ltd.
+ */
+
+#ifndef __DT_BINDINGS_PINCTRL_STARFIVE_JH7110_H__
+#define __DT_BINDINGS_PINCTRL_STARFIVE_JH7110_H__
+
+/* sys_iomux pin */
+#define PAD_GPIO0 0
+#define PAD_GPIO1 1
+#define PAD_GPIO2 2
+#define PAD_GPIO3 3
+#define PAD_GPIO4 4
+#define PAD_GPIO5 5
+#define PAD_GPIO6 6
+#define PAD_GPIO7 7
+#define PAD_GPIO8 8
+#define PAD_GPIO9 9
+#define PAD_GPIO10 10
+#define PAD_GPIO11 11
+#define PAD_GPIO12 12
+#define PAD_GPIO13 13
+#define PAD_GPIO14 14
+#define PAD_GPIO15 15
+#define PAD_GPIO16 16
+#define PAD_GPIO17 17
+#define PAD_GPIO18 18
+#define PAD_GPIO19 19
+#define PAD_GPIO20 20
+#define PAD_GPIO21 21
+#define PAD_GPIO22 22
+#define PAD_GPIO23 23
+#define PAD_GPIO24 24
+#define PAD_GPIO25 25
+#define PAD_GPIO26 26
+#define PAD_GPIO27 27
+#define PAD_GPIO28 28
+#define PAD_GPIO29 29
+#define PAD_GPIO30 30
+#define PAD_GPIO31 31
+#define PAD_GPIO32 32
+#define PAD_GPIO33 33
+#define PAD_GPIO34 34
+#define PAD_GPIO35 35
+#define PAD_GPIO36 36
+#define PAD_GPIO37 37
+#define PAD_GPIO38 38
+#define PAD_GPIO39 39
+#define PAD_GPIO40 40
+#define PAD_GPIO41 41
+#define PAD_GPIO42 42
+#define PAD_GPIO43 43
+#define PAD_GPIO44 44
+#define PAD_GPIO45 45
+#define PAD_GPIO46 46
+#define PAD_GPIO47 47
+#define PAD_GPIO48 48
+#define PAD_GPIO49 49
+#define PAD_GPIO50 50
+#define PAD_GPIO51 51
+#define PAD_GPIO52 52
+#define PAD_GPIO53 53
+#define PAD_GPIO54 54
+#define PAD_GPIO55 55
+#define PAD_GPIO56 56
+#define PAD_GPIO57 57
+#define PAD_GPIO58 58
+#define PAD_GPIO59 59
+#define PAD_GPIO60 60
+#define PAD_GPIO61 61
+#define PAD_GPIO62 62
+#define PAD_GPIO63 63
+#define PAD_SD0_CLK 64
+#define PAD_SD0_CMD 65
+#define PAD_SD0_DATA0 66
+#define PAD_SD0_DATA1 67
+#define PAD_SD0_DATA2 68
+#define PAD_SD0_DATA3 69
+#define PAD_SD0_DATA4 70
+#define PAD_SD0_DATA5 71
+#define PAD_SD0_DATA6 72
+#define PAD_SD0_DATA7 73
+#define PAD_SD0_STRB 74
+#define PAD_GMAC1_MDC 75
+#define PAD_GMAC1_MDIO 76
+#define PAD_GMAC1_RXD0 77
+#define PAD_GMAC1_RXD1 78
+#define PAD_GMAC1_RXD2 79
+#define PAD_GMAC1_RXD3 80
+#define PAD_GMAC1_RXDV 81
+#define PAD_GMAC1_RXC 82
+#define PAD_GMAC1_TXD0 83
+#define PAD_GMAC1_TXD1 84
+#define PAD_GMAC1_TXD2 85
+#define PAD_GMAC1_TXD3 86
+#define PAD_GMAC1_TXEN 87
+#define PAD_GMAC1_TXC 88
+#define PAD_QSPI_SCLK 89
+#define PAD_QSPI_CS0 90
+#define PAD_QSPI_DATA0 91
+#define PAD_QSPI_DATA1 92
+#define PAD_QSPI_DATA2 93
+#define PAD_QSPI_DATA3 94
+
+#define GPOUT_LOW 0
+#define GPOUT_HIGH 1
+
+#define GPOEN_ENABLE 0
+#define GPOEN_DISABLE 1
+
+#define GPI_NONE 255
+
+#endif
--
2.38.1
More information about the linux-riscv
mailing list