pccard hang.
Chris Ball
cjb at mrao.cam.ac.uk
Wed May 31 12:49:29 EDT 2006
Thanks for the reply, Dominik.
> Either the memory ranges are broken, or the IRQ. Do you know, by
> chance, which does cause this failure? You could test whether it is
> the memory range by adding reserved=0xff490000,0x00aff000 to the
> kenrel boot line, and check whether it works.
Adding reserve=0xff490000,0x00aff000 fixed the crash, thanks.
> On very most systems there is no such crash; in fact, your notebook
> seems to be the first on where the autoconfiguration fails.
> Could you send me a complete dmesg, please?
Sure. I can't easily get a dmesg of the crashing case, but here's one
for the working case, where the card is inserted after udev is up. I've
tried pci=routeirq and pci=assign-busses in case either was relevant, as
suggested by dmesg, but they didn't change anything.
-------------- next part --------------
Linux version 2.6.16-1.2230_FC6 (bhcompile at hs20-bc1-5.build.redhat.com) (gcc version 4.1.1 20060525 (Red Hat 4.1.1-1)) #1 SMP Mon May 29 23:25:36 EDT 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001f7d0000 (usable)
BIOS-e820: 000000001f7d0000 - 000000001f7de000 (ACPI data)
BIOS-e820: 000000001f7de000 - 000000001f800000 (ACPI NVS)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fed13000 - 00000000fed1a000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
503MB LOWMEM available.
found SMP MP-table at 000ff780
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 128976
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 124880 pages, LIFO batch:31
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP (v000 ACPIAM ) @ 0x000f8870
ACPI: RSDT (v001 A M I OEMRSDT 0x11000524 MSFT 0x00000097) @ 0x1f7d0000
ACPI: FADT (v002 A M I OEMFACP 0x11000524 MSFT 0x00000097) @ 0x1f7d0200
ACPI: MADT (v001 A M I OEMAPIC 0x11000524 MSFT 0x00000097) @ 0x1f7d0390
ACPI: MCFG (v001 A M I OEMMCFG 0x11000524 MSFT 0x00000097) @ 0x1f7d03f0
ACPI: OEMB (v001 A M I AMI_OEM 0x11000524 MSFT 0x00000097) @ 0x1f7de040
ACPI: MCFG (v001 A M I OEMMCFG 0x11000524 MSFT 0x00000097) @ 0x1f7d4b60
ACPI: SSDT (v001 AMI0 CPU1PM 0x00000001 INTL 0x02002026) @ 0x1f7d4ba0
ACPI: DSDT (v001 255EI 255EI008 0x00000008 INTL 0x02002026) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 20000000 (gap: 1f800000:c0800000)
Built 1 zonelists
Kernel command line: ro root=/dev/group0/slash rhgb quiet
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c079e000 soft=c077e000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 1733.655 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 503648k/515904k available (2113k kernel code, 11620k reserved, 1181k data, 240k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3470.71 BogoMIPS (lpj=6941430)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
CPU: After vendor identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9f3ff 00100000 00000000 00000040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
CPU0: Intel(R) Pentium(R) M processor 1.73GHz stepping 08
Total of 1 processors activated (3470.71 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
checking if image is initramfs... it is
Freeing initrd memory: 1809k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
ACPI: 2 duplicate MCFG table ignored.
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #02 (-#05) is hidden behind transparent bridge #01 (-#02) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: Embedded Controller [EC0] (gpe 24) interrupt mode.
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bus 2, cardbus bridge: 0000:01:03.0
IO window: 0000c000-0000c0ff
IO window: 0000c400-0000c4ff
PREFETCH window: 22000000-23ffffff
MEM window: 24000000-25ffffff
PCI: Bridge: 0000:00:1e.0
IO window: c000-dfff
MEM window: ff400000-ffcfffff
PREFETCH window: bdf00000-bfefffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:01:03.0[A] -> GSI 17 (level, low) -> IRQ 169
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 6, 327680 bytes)
TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1149092652.372:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key F7020D0232336C93
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: Thermal Zone [THRM] (59 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 915GM Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xd0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
Probing IDE interface ide1...
hdc: _NEC DVD_RW ND-6750A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ide-floppy driver 0.99.newide
ACPI: PCI Interrupt 0000:01:03.0[A] -> GSI 17 (level, low) -> IRQ 169
Yenta: CardBus bridge found at 0000:01:03.0 [1584:3200]
Yenta: adjusting diagnostic: 40 -> 60
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:01:03.0, mfunc 0x000c1002, devctl 0x44
Yenta: ISA IRQ mask 0x0cf8, PCI irq 169
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0xc000 - 0xdfff
cs: IO port probe 0xc000-0xdfff: clean.
pcmcia: parent PCI bridge Memory window: 0xff400000 - 0xffcfffff
pcmcia: parent PCI bridge Memory window: 0xbdf00000 - 0xbfefffff
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.0.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
ACPI wakeup devices:
P0P2 P0P1 LAN CBUS MC97 AZC P0P4 P0P5 P0P6 P0P7
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 240k freed
Write protecting the kernel read-only data: 707k
input: AT Translated Set 2 keyboard as /class/input/input0
SCSI subsystem initialized
libata version 1.20 loaded.
ata_piix 0000:00:1f.2: version 1.05
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 177
ata: 0x170 IDE port busy
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xFFA0 irq 14
ata1: dev 0 cfg 49:2f00 82:346b 83:7f09 84:6003 85:3c69 86:3c01 87:6003 88:203f
ata1: dev 0 ATA-7, max UDMA/100, 78242976 sectors: LBA48
ata1(0): applying bridge limits
ata1: dev 0 configured for UDMA/100
scsi0 : ata_piix
Vendor: ATA Model: SAMSUNG MP0402H Rev: UC10
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 78242976 512-byte hdwr sectors (40060 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 78242976 512-byte hdwr sectors (40060 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda:<6>Synaptics Touchpad, model: 1, fw: 6.2, id: 0xa0b1, caps: 0xa04713/0x20040a
input: SynPS/2 Synaptics TouchPad as /class/input/input1
sda1 sda2
sd 0:0:0:0: Attached scsi disk sda
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel at redhat.com
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1149092656.508:2): selinux=0 auid=4294967295
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt 0000:01:0c.0[A] -> GSI 19 (level, low) -> IRQ 177
eth0: Identified chip type is 'RTL8169s/8110s'.
eth0: RTL8169 at 0xe0078c00, 00:03:0d:39:f8:ed, IRQ 177
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 185, io base 0x0000e400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 177, io base 0x0000e480
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ieee80211_crypt: registered algorithm 'NULL'
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 185, io mem 0xffe3fc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
ieee1394: Initialized config rom entry `ip1394'
ieee80211: 802.11 data/management/control stack, git-1.1.7
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno at linux.intel.com>
ACPI: PCI Interrupt 0000:01:0a.0[A] -> GSI 18 (level, low) -> IRQ 193
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[193] MMIO=[ffcff000-ffcff7ff] Max Packet=[2048] IR/IT contexts=[4/8]
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 193, io base 0x0000e800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 201, io base 0x0000e880
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, git-1.1.1
ipw2200: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt 0000:01:07.0[A] -> GSI 19 (level, low) -> IRQ 177
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
sd 0:0:0:0: Attached scsi generic sg0 type 0
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
ipw2200: Radio Frequency Kill Switch is On:
Kill switch must be turned off for wireless networking to work.
ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
cs: IO port probe 0xfc00-0xfcff: clean.
cs: IO port probe 0xfd00-0xfdff: clean.
hw_random hardware driver 1.0.0 loaded
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00030d49255fff40]
floppy0: no floppy controllers found
lp: driver loaded but no devices found
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ACPI: AC Adapter [AC0] (off-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
ACPI: Video Device [PEG] (multi-head: yes rom: no post: no)
ACPI: Video Device [IGD] (multi-head: yes rom: no post: no)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: dm-multipath version 1.0.4 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2097144k swap on /dev/group0/swap. Priority:-1 extents:1 across:2097144k
r8169: eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
audit(1149092689.835:3): audit_pid=1779 old=0 by auid=4294967295
Bluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.7
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
ADDRCONF(NETDEV_UP): eth1: link is not ready
r8169: eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 201
[drm] Initialized i915 1.4.0 20060119 on minor 0
pccard: PCMCIA card inserted into slot 0
cs: memory probe 0xffeff000-0xffefffff: excluding 0xffeff000-0xfff00fff
pcmcia: registering new device pcmcia0.0
orinoco 0.15rc3 (David Gibson <hermes at gibson.dropbear.id.au>, Pavel Roskin <proski at gnu.org>, et al)
orinoco_cs 0.15rc3 (David Gibson <hermes at gibson.dropbear.id.au>, Pavel Roskin <proski at gnu.org>, et al)
eth2: Hardware identity 0001:0001:0004:0000
eth2: Station identity 001f:0001:0007:001c
eth2: Firmware determined as Lucent/Agere 7.28
eth2: Ad-hoc demo mode supported
eth2: IEEE standard IBSS ad-hoc mode supported
eth2: WEP supported, 104-bit key
eth2: MAC address 00:02:2D:0D:5A:C8
eth2: Station name "HERMES I"
eth2: ready
eth2: index 0x01: , irq 7, io 0xc100-0xc13f
ADDRCONF(NETDEV_UP): eth2: link is not ready
eth2: New link status: Disconnected (0002)
eth2: New link status: Connected (0001)
ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
eth2: New link status: Disconnected (0002)
eth2: New link status: Connected (0001)
ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
eth2: no IPv6 routers present
-------------- next part --------------
- Chris.
--
Chris Ball <cjb at mrao.cam.ac.uk> <http://blog.printf.net/>
More information about the linux-pcmcia
mailing list