[v4,1/3] net: stmmac: s32: use a syscon for S32_PHY_INTF_SEL_RGMII

[Simon Horman]

On Mon, Jan 26, 2026 at 03:33:54PM +0000, Russell King (Oracle) wrote:
> On Mon, Jan 26, 2026 at 03:24:30PM +0000, Simon Horman wrote:
> > This is an AI-generated review of your patch. The human sending this
> > email has considered the AI review valid, or at least plausible.
> > 
> > For local reproduction steps see https://netdev-ai.bots.linux.dev/ai-local.html
> > ---
> >     net: stmmac: s32: use a syscon for S32_PHY_INTF_SEL_RGMII
> > 
> > This commit adds syscon/regmap support for accessing the GMAC_0_CTRL_STS
> > register on s32 chipsets, while maintaining backwards compatibility with
> > the existing direct MMIO approach for older device trees.
> > 
> > > diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-s32.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-s32.c
> > > index 5a485ee98fa7..2e6bb41f49e1 100644
> > > --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-s32.c
> > > +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-s32.c
> > 
> > [ ... ]
> > 
> > > @@ -40,7 +44,10 @@ struct s32_priv_data {
> > >
> > >  static int s32_gmac_write_phy_intf_select(struct s32_priv_data *gmac)
> > >  {
> > > -	writel(S32_PHY_INTF_SEL_RGMII, gmac->ctrl_sts);
> > > +	if (gmac->ctrl_sts)
> > > +		writel(S32_PHY_INTF_SEL_RGMII, gmac->ctrl_sts);
> > > +	else
> > > +		regmap_write(gmac->sts_regmap, gmac->sts_offset, S32_PHY_INTF_SEL_RGMII);
> > 
> > Should the regmap_write() return value be checked here? The function
> > returns int and the caller s32_gmac_init() checks the return value
> > expecting errors to be propagated. For comparison, dwmac-sun55i.c in
> > sun55i_gmac200_set_syscon() does check regmap_write() return value:
> > 
> >     ret = regmap_write(regmap, SYSCON_REG, reg);
> >     if (ret < 0)
> >         return dev_err_probe(dev, ret, "Failed to write to syscon\n");
> 
> AI is wrong on this last line - s32_gmac_write_phy_intf_select() is
> called from s32_gmac_init(), which is called from plat_dat->init.
> 
> plat_dat->init is called from two paths:
> 
> 1. stmmac_pltfr_probe() -> stmmac_dvr_probe() -> plat_dat->init()
> 
> 2. stmmac_resume() -> plat_dat->resume() -> stmmac_plat_resume() ->
>    stmmac_pltfr_init() -> plat_dat->init()
> 
> In the resume path, it is not appropriate to use dev_err_probe()
> because we're not in the probe path.

Hi Russell,

I agree that using dev_err_probe() is not appropriate here.
And, FWIIW, I took that part to be an illustration that
sun55i_gmac200_set_syscon() handles a similar case,
rather than a suggestion of how to handle it here.

But at any rate, I think the key question is should the case
where regmap_write() returns an error be handled in
s32_gmac_write_phy_intf_select() (by some means)?