[PATCH 1/3] arm64: dts: rockchip: Change gmac phy-mode to rgmii-id for rk3576 evb1

[Chaoyi Chen]

From: Chaoyi Chen <chaoyi.chen at rock-chips.com>

According to the description in the net documentation, PHY modes
"rgmii", "rgmii-rxid" and "rgmii-txid" modes require the clock signal
to be delayed on the PCB.

The Rockchip platform has long used the above mentioned PHY modes and
private delay prop to describe the internal IO delay settings of the
chip, which is inconsistent with what is described in the documentation.

Let's describe this part of the delay in the PHY and use the more
reasonable "rgmii-id" mode.

Signed-off-by: Chaoyi Chen <chaoyi.chen at rock-chips.com>
---
 arch/arm64/boot/dts/rockchip/rk3576-evb1-v10.dts | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3576-evb1-v10.dts b/arch/arm64/boot/dts/rockchip/rk3576-evb1-v10.dts
index c5584c26db52..3ee76bafafb5 100644
--- a/arch/arm64/boot/dts/rockchip/rk3576-evb1-v10.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3576-evb1-v10.dts
@@ -266,7 +266,7 @@ &combphy1_psu {
 
 &gmac0 {
 	clock_in_out = "output";
-	phy-mode = "rgmii-rxid";
+	phy-mode = "rgmii-id";
 	phy-handle = <&rgmii_phy0>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&eth0m0_miim
@@ -275,14 +275,13 @@ &eth0m0_rx_bus2
 		     &eth0m0_rgmii_clk
 		     &eth0m0_rgmii_bus
 		     &ethm0_clk0_25m_out>;
-	tx_delay = <0x21>;
 	status = "okay";
 };
 
 &gmac1 {
 	clock_in_out = "output";
 	phy-handle = <&rgmii_phy1>;
-	phy-mode = "rgmii-rxid";
+	phy-mode = "rgmii-id";
 	pinctrl-names = "default";
 	pinctrl-0 = <&eth1m0_miim
 		     &eth1m0_tx_bus2
@@ -290,7 +289,6 @@ &eth1m0_rx_bus2
 		     &eth1m0_rgmii_clk
 		     &eth1m0_rgmii_bus
 		     &ethm0_clk1_25m_out>;
-	tx_delay = <0x20>;
 	status = "okay";
 };
 
@@ -721,6 +719,7 @@ rgmii_phy0: ethernet-phy at 1 {
 		reset-assert-us = <20000>;
 		reset-deassert-us = <100000>;
 		reset-gpios = <&gpio2 RK_PB5 GPIO_ACTIVE_LOW>;
+		tx-internal-delay-ps = <1950>;
 	};
 };
 
@@ -737,6 +736,7 @@ rgmii_phy1: ethernet-phy at 1 {
 		reset-assert-us = <20000>;
 		reset-deassert-us = <100000>;
 		reset-gpios = <&gpio3 RK_PA3 GPIO_ACTIVE_LOW>;
+		tx-internal-delay-ps = <1950>;
 	};
 };
 
-- 
2.51.1