[RFC V2 2/4] firmware: arm_scmi: vendors: Add QCOM vendor protocol
Sibi Sankar
quic_sibis at quicinc.com
Wed Jun 12 11:30:29 PDT 2024
The SCMI QCOM vendor protocol provides a generic way of exposing a
number of Qualcomm SoC specific features (like memory bus scaling)
through a mixture of pre-determined algorithm strings and param_id
pairs hosted on the SCMI controller.
Co-developed-by: Shivnandan Kumar <quic_kshivnan at quicinc.com>
Signed-off-by: Shivnandan Kumar <quic_kshivnan at quicinc.com>
Co-developed-by: Ramakrishna Gottimukkula <quic_rgottimu at quicinc.com>
Signed-off-by: Ramakrishna Gottimukkula <quic_rgottimu at quicinc.com>
Co-developed-by: Amir Vajid <avajid at quicinc.com>
Signed-off-by: Amir Vajid <avajid at quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis at quicinc.com>
---
v1:
* Rebase on top of Cristian's "SCMI multiple vendor protocol support" series. [Cristian]
* Add more documentation wherever possible. [Sudeep]
drivers/firmware/arm_scmi/vendors/Kconfig | 12 ++
drivers/firmware/arm_scmi/vendors/Makefile | 2 +-
.../arm_scmi/vendors/qcom_scmi_vendor.c | 184 ++++++++++++++++++
include/linux/qcom_scmi_vendor.h | 39 ++++
4 files changed, 236 insertions(+), 1 deletion(-)
create mode 100644 drivers/firmware/arm_scmi/vendors/qcom_scmi_vendor.c
create mode 100644 include/linux/qcom_scmi_vendor.h
diff --git a/drivers/firmware/arm_scmi/vendors/Kconfig b/drivers/firmware/arm_scmi/vendors/Kconfig
index 7c1ca7a12603..6bff4550fa25 100644
--- a/drivers/firmware/arm_scmi/vendors/Kconfig
+++ b/drivers/firmware/arm_scmi/vendors/Kconfig
@@ -1,4 +1,16 @@
# SPDX-License-Identifier: GPL-2.0-only
menu "ARM SCMI Vendor Protocols"
+config ARM_SCMI_PROTOCOL_VENDOR_QCOM
+ tristate "Qualcomm Technologies, Inc. Qcom SCMI vendor Protocol"
+ depends on ARM_SCMI_PROTOCOL || COMPILE_TEST
+ help
+ The SCMI QCOM vendor protocol provides a generic way of exposing a
+ number of Qualcomm SoC specific features (like memory bus scaling)
+ through a mixture of pre-determined algorithm strings and param_id
+ pairs hosted on the SCMI controller.
+
+ This driver defines/documents the message ID's used for this
+ communication and also exposes the ops used by the clients.
+
endmenu
diff --git a/drivers/firmware/arm_scmi/vendors/Makefile b/drivers/firmware/arm_scmi/vendors/Makefile
index c6c214158dd8..c1d6a355f579 100644
--- a/drivers/firmware/arm_scmi/vendors/Makefile
+++ b/drivers/firmware/arm_scmi/vendors/Makefile
@@ -1,2 +1,2 @@
# SPDX-License-Identifier: GPL-2.0-only
-# obj-$(CONFIG_ARM_SCMI_PROTOCOL_<your_vendor_proto>) += <your_vendor_proto>.o
+obj-$(CONFIG_ARM_SCMI_PROTOCOL_VENDOR_QCOM) += qcom_scmi_vendor.o
diff --git a/drivers/firmware/arm_scmi/vendors/qcom_scmi_vendor.c b/drivers/firmware/arm_scmi/vendors/qcom_scmi_vendor.c
new file mode 100644
index 000000000000..e02163381d4b
--- /dev/null
+++ b/drivers/firmware/arm_scmi/vendors/qcom_scmi_vendor.c
@@ -0,0 +1,184 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2024, Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <linux/qcom_scmi_vendor.h>
+
+#include "../common.h"
+
+/**
+ * qcom_scmi_vendor_protocol_cmd - vendor specific commands supported by Qualcomm SCMI
+ * vendor protocol.
+ *
+ * This protocol is intended as a generic way of exposing a number of Qualcomm SoC
+ * specific features through a mixture of pre-determined algorithm string and param_id
+ * pairs hosted on the SCMI controller.
+ *
+ * The QCOM SCMI Vendor Protocol has the protocol id as 0x80 and vendor id set to
+ * Qualcomm and the implementation version set to 0x20000. The PROTOCOL_VERSION command
+ * returns version 1.0.
+ *
+ * @QCOM_SCMI_SET_PARAM: message_id: 0x10 is used to set the parameter of a specific algo_str
+ * hosted on QCOM SCMI Vendor Protocol. The tx len depends on the
+ * algo_str used.
+ * @QCOM_SCMI_GET_PARAM: message_id: 0x11 is used to get parameter information of a specific
+ * algo_str hosted on QCOM SCMI Vendor Protocol. The tx and rx len
+ * depends on the algo_str used.
+ * @QCOM_SCMI_START_ACTIVITY: message_id: 0x12 is used to start the activity performed by
+ * the algo_str.
+ * @QCOM_SCMI_STOP_ACTIVITY: message_id: 0x13 is used to stop a pre-existing activity
+ * performed by the algo_str.
+ */
+enum qcom_scmi_vendor_protocol_cmd {
+ QCOM_SCMI_SET_PARAM = 0x10,
+ QCOM_SCMI_GET_PARAM = 0x11,
+ QCOM_SCMI_START_ACTIVITY = 0x12,
+ QCOM_SCMI_STOP_ACTIVITY = 0x13,
+};
+
+/**
+ * struct qcom_scmi_msg - represents the various parameters to be populated
+ * for using the QCOM SCMI Vendor Protocol
+ *
+ * @ext_id: reserved, must be zero
+ * @algo_low: lower 32 bits of the algo_str
+ * @algo_high: upper 32 bits of the algo_str
+ * @param_id: serves as token message id to the specific algo_str
+ * @buf: serves as the payload to the specified param_id and algo_str pair
+ */
+struct qcom_scmi_msg {
+ __le32 ext_id;
+ __le32 algo_low;
+ __le32 algo_high;
+ __le32 param_id;
+ __le32 buf[];
+};
+
+static int qcom_scmi_set_param(const struct scmi_protocol_handle *ph, void *buf, u64 algo_str,
+ u32 param_id, size_t size)
+{
+ struct scmi_xfer *t;
+ struct qcom_scmi_msg *msg;
+ int ret;
+
+ ret = ph->xops->xfer_get_init(ph, QCOM_SCMI_SET_PARAM, size + sizeof(*msg), 0, &t);
+ if (ret)
+ return ret;
+
+ msg = t->tx.buf;
+ msg->algo_low = cpu_to_le32(lower_32_bits(algo_str));
+ msg->algo_high = cpu_to_le32(upper_32_bits(algo_str));
+ msg->param_id = cpu_to_le32(param_id);
+
+ memcpy(msg->buf, buf, t->tx.len - sizeof(*msg));
+
+ ret = ph->xops->do_xfer(ph, t);
+ ph->xops->xfer_put(ph, t);
+
+ return ret;
+}
+
+static int qcom_scmi_get_param(const struct scmi_protocol_handle *ph, void *buf, u64 algo_str,
+ u32 param_id, size_t tx_size, size_t rx_size)
+{
+ struct scmi_xfer *t;
+ struct qcom_scmi_msg *msg;
+ int ret;
+
+ ret = ph->xops->xfer_get_init(ph, QCOM_SCMI_GET_PARAM, tx_size + sizeof(*msg), rx_size, &t);
+ if (ret)
+ return ret;
+
+ msg = t->tx.buf;
+ msg->algo_low = cpu_to_le32(lower_32_bits(algo_str));
+ msg->algo_high = cpu_to_le32(upper_32_bits(algo_str));
+ msg->param_id = cpu_to_le32(param_id);
+ memcpy(msg->buf, buf, t->tx.len - sizeof(*msg));
+
+ ret = ph->xops->do_xfer(ph, t);
+ memcpy(buf, t->rx.buf, t->rx.len);
+ ph->xops->xfer_put(ph, t);
+
+ return ret;
+}
+
+static int qcom_scmi_start_activity(const struct scmi_protocol_handle *ph,
+ void *buf, u64 algo_str, u32 param_id, size_t size)
+{
+ struct scmi_xfer *t;
+ struct qcom_scmi_msg *msg;
+ int ret;
+
+ ret = ph->xops->xfer_get_init(ph, QCOM_SCMI_START_ACTIVITY, size + sizeof(*msg), 0, &t);
+ if (ret)
+ return ret;
+
+ msg = t->tx.buf;
+ msg->algo_low = cpu_to_le32(lower_32_bits(algo_str));
+ msg->algo_high = cpu_to_le32(upper_32_bits(algo_str));
+ msg->param_id = cpu_to_le32(param_id);
+
+ memcpy(msg->buf, buf, t->tx.len - sizeof(*msg));
+
+ ret = ph->xops->do_xfer(ph, t);
+ ph->xops->xfer_put(ph, t);
+
+ return ret;
+}
+
+static int qcom_scmi_stop_activity(const struct scmi_protocol_handle *ph, void *buf, u64 algo_str,
+ u32 param_id, size_t size)
+{
+ struct scmi_xfer *t;
+ struct qcom_scmi_msg *msg;
+ int ret;
+
+ ret = ph->xops->xfer_get_init(ph, QCOM_SCMI_STOP_ACTIVITY, size + sizeof(*msg), 0, &t);
+ if (ret)
+ return ret;
+
+ msg = t->tx.buf;
+ msg->algo_low = cpu_to_le32(lower_32_bits(algo_str));
+ msg->algo_high = cpu_to_le32(upper_32_bits(algo_str));
+ msg->param_id = cpu_to_le32(param_id);
+
+ memcpy(msg->buf, buf, t->tx.len - sizeof(*msg));
+
+ ret = ph->xops->do_xfer(ph, t);
+ ph->xops->xfer_put(ph, t);
+
+ return ret;
+}
+
+static struct qcom_scmi_vendor_ops qcom_proto_ops = {
+ .set_param = qcom_scmi_set_param,
+ .get_param = qcom_scmi_get_param,
+ .start_activity = qcom_scmi_start_activity,
+ .stop_activity = qcom_scmi_stop_activity,
+};
+
+static int qcom_scmi_vendor_protocol_init(const struct scmi_protocol_handle *ph)
+{
+ u32 version;
+
+ ph->xops->version_get(ph, &version);
+
+ dev_dbg(ph->dev, "SCMI QCOM Vendor Version %d.%d\n",
+ PROTOCOL_REV_MAJOR(version), PROTOCOL_REV_MINOR(version));
+
+ return 0;
+}
+
+static const struct scmi_protocol qcom_scmi_vendor = {
+ .id = QCOM_SCMI_VENDOR_PROTOCOL,
+ .owner = THIS_MODULE,
+ .instance_init = &qcom_scmi_vendor_protocol_init,
+ .ops = &qcom_proto_ops,
+ .vendor_id = "Qualcomm",
+ .impl_ver = 0x20000,
+};
+module_scmi_protocol(qcom_scmi_vendor);
+
+MODULE_DESCRIPTION("QTI SCMI vendor protocol");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/qcom_scmi_vendor.h b/include/linux/qcom_scmi_vendor.h
new file mode 100644
index 000000000000..60f85fedee80
--- /dev/null
+++ b/include/linux/qcom_scmi_vendor.h
@@ -0,0 +1,39 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * QTI SCMI vendor protocol's header
+ *
+ * Copyright (c) 2024, Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#ifndef _QCOM_SCMI_VENDOR_H
+#define _QCOM_SCMI_VENDOR_H
+
+#include <linux/bitfield.h>
+#include <linux/device.h>
+#include <linux/types.h>
+
+#define QCOM_SCMI_VENDOR_PROTOCOL 0x80
+
+struct scmi_protocol_handle;
+
+/**
+ * struct qcom_scmi_vendor_ops - represents the various operations provided
+ * by QCOM SCMI Vendor Protocol
+ *
+ * @set_param: set parameter specified by param_id and algo_str pair.
+ * @get_param: retrieve parameter specified by param_id and algo_str pair.
+ * @start_activity: initiate a specific activity defined by algo_str.
+ * @stop_activity: halt previously initiated activity defined by algo_str.
+ */
+struct qcom_scmi_vendor_ops {
+ int (*set_param)(const struct scmi_protocol_handle *ph, void *buf, u64 algo_str,
+ u32 param_id, size_t size);
+ int (*get_param)(const struct scmi_protocol_handle *ph, void *buf, u64 algo_str,
+ u32 param_id, size_t tx_size, size_t rx_size);
+ int (*start_activity)(const struct scmi_protocol_handle *ph, void *buf, u64 algo_str,
+ u32 param_id, size_t size);
+ int (*stop_activity)(const struct scmi_protocol_handle *ph, void *buf, u64 algo_str,
+ u32 param_id, size_t size);
+};
+
+#endif /* _QCOM_SCMI_VENDOR_H */
--
2.34.1
More information about the linux-arm-kernel
mailing list