[PATCH v1 1/2] arm64: dts: ti: k3-am62: Add MCU MCAN nodes

[Judith Mendez]

Hi Francesco,

On 7/24/23 8:36 AM, Francesco Dolcini wrote:
> From: Judith Mendez <jm at ti.com>
> 
> On AM62x there are no hardware interrupts routed to A53 GIC
> interrupt controller for MCU MCAN IPs, so MCU MCAN nodes were
> omitted from MCU dtsi.
> 
> Timer polling was introduced in commits [1][2] so now add MCU MCAN nodes
> to the MCU dtsi for the Cortex A53.
> 
> [1] b382380c0d2d ("can: m_can: Add hrtimer to generate software interrupt")
> [2] bb410c03b999 ("dt-bindings: net: can: Remove interrupt properties for MCAN")
> 
> Signed-off-by: Judith Mendez <jm at ti.com>
> [fd: fixed labels to match datasheet numbering, revised commit message,
>       fixed reg/reg-names order]
> Signed-off-by: Francesco Dolcini <francesco.dolcini at toradex.com>
> ---
>   arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi | 24 ++++++++++++++++++++++++
>   1 file changed, 24 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi
> index 19fc38157d94..fed50666d95b 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi
> @@ -147,4 +147,28 @@ mcu_rti0: watchdog at 4880000 {
>   		/* Tightly coupled to M4F */
>   		status = "reserved";
>   	};
> +
> +	mcu_mcan0: can at 4e00000 {
> +		compatible = "bosch,m_can";
> +		reg = <0x00 0x4e08000 0x00 0x200>,
> +		      <0x00 0x4e00000 0x00 0x8000>;
> +		reg-names = "m_can", "message_ram";
> +		power-domains = <&k3_pds 188 TI_SCI_PD_EXCLUSIVE>;
> +		clocks = <&k3_clks 188 6>, <&k3_clks 188 1>;
> +		clock-names = "hclk", "cclk";
> +		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
> +		status = "disabled";
> +	};
> +
> +	mcu_mcan1: can at 4e10000 {
> +		compatible = "bosch,m_can";
> +		reg = <0x00 0x4e18000 0x00 0x200>,
> +		      <0x00 0x4e10000 0x00 0x8000>;
> +		reg-names = "m_can", "message_ram";
> +		power-domains = <&k3_pds 189 TI_SCI_PD_EXCLUSIVE>;
> +		clocks = <&k3_clks 189 6>, <&k3_clks 189 1>;
> +		clock-names = "hclk", "cclk";
> +		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
> +		status = "disabled";
> +	};
>   };

Thanks for sending this patch, will also send for AM62ax.

~ Judith